confirm if "negotiation auto" is supported gigabit port for C3925E router.
Router(config-if)#Interface gi0/2
Router(config-if)#description test link
Router(config-if)# no ip address
Router(config-if)# negotiation auto
^
% Invalid input detected at '^' marker.
Nexus 5500 support auto negotiation on 1gig sfp port? There is an end device that only support auto negotiation and cannot be manually set speed/duplex.
View 0 Replies View RelatedI have already exploited Metro Ethernet, but I don't understand why auto-negotiation does not support for Ten Giga ports?
View 8 Replies View RelatedI've a D-Link DFE-520TX PCI Fast Ethernet card, which is/was excellent until this first problem. 2 nights ago there was some good lightning/thunders activity, resulting in burning of ISP network switches. This morning they replaced the switches and brought up the network, but here's the problem:1) Under the default card setting with Auto-negotiation, PC looks for DCHP Server address resolution and ends up with YELLOW triangle in the system tray.2) Whereas, when I CHANGE the card setting to 10Base in FullDuplex, then PC gets connected to the ISP network.ISP support said that either the card could be damaged due to lightning strike or it could be due to damaged cable running from port box to the PC (RJ-45). I'm wondering, could lightning strike damage a Network card in such a partial manner (just one feature, i.e., Auto-negotiation)? But that person warned, there will be deterioration in ISP speeds when I use 10Base in Full Duplex (for now) compared to Auto-negotiation speeds. Speeds really came down badly, that's understood.
View 9 Replies View RelatedWe are facing to an annoying issue. We have a 6509 running in Catos 8.3(4) with WS-X6548-GE-TX, WS-X6348-RJ-45 and WS-X6148-RJ-45. When we configure the mode in auto negotiation, it comes up in half duplex. We need to configure the speed mode at 100Mbit/Full to make it work. But if the chassis or port restarts (not the server), the link becomes half duplex. This happens only on module in Gigabyte like WS-X6548-GE-TX.
Cable have been replaced but does not work. It is not happened on another chassis running on IOS 12.2(18)SXF17b with WS-X6548-GE-TX.
I have a question about speed negotiation process between interfaces. I have 3650X Sw and 2960S-48port. All ports of two are GigabitEthernet, however the link between them is only 100Mb/s, Full duplex. I try to set the speed 1000 Mb/s manually in the interface then the interface never up. Its status is down/down. I must set back to speed auto. I show interface Gigabit0/24 in Sw 3650-X and figure out that there are many output drop (over 600000). I clear counter then after two days the output drop is over 70000. This link is trunk link between two switches, all ports of access SW are Gigabit and connect to PC. First, I thinks the 3650X is throttled somewhere in output direction of trunk link. But there is another trunk link (Gi0/23) to another 2960S-48port and no output drop number in this interface. This Giga 0/23 speed is 1000 Mb/s (auto speed, auto duplex)
Does any outside things impact the speed negotiation process between 2 interfaces? And output drop number may caused by abnormal speed between two Gigabit interface?
I have a Cisco 2851 router and need an additional gigabit Ethernet port. How to get the part number I need to order?
View 3 Replies View RelatedI have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies View RelatedCan we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies View RelatedWe have Cisco 7609 Router and one 6 Mbps link which is on ethernet . When we are trerminating on Gigaethernet of 7609 router it is not coming up. While same link is showing up and working fine on other routers which is having Ethernet interface.
View 1 Replies View RelatedI am having a problem with my Realtek RTL8168D/8111D PCI-E Gigabit Ethernet NIC. It is not detecting my ethernet cable, and thus leaving me without internet on my desktop, after i updated its driver. The cable is not the problem as I have tested the cable with my laptop. I tried rolling back drivers, doing system restore and removing drivers with driversweeper and letting windows install the drivers again. However, none of these worked for me. I doubt the NIC is faulty as it was working before i updated the drivers. I am using windows 7 home premium 64-bit.
View 9 Replies View RelatedI was unable to telnet in to a SQL server on port 1433 to test the connection from the client PC.the application could connect and this alone verifies it is working on port 1433 for sql.My question is how can a telnet command on a specific port be blocked ?
View 3 Replies View RelatedIs there a way to ask the above switch how much power it's supplying to various ports?I've found some stuff in POWER-ETHERNET-MIB, but it's only the main power supply and the up/down status of the various ports.
It looks like what I want is
[URL]
but my SG500 tells me:
snmpwalk -v2c -cpublic serverswitch 1.3.6.1.4.1.9.9.402
CISCO-SMI::ciscoMgmt.402 = No Such Object available on this agent at this OID
i have a cisco 1921 router and it has ge0/0 (LAN) and ge(0/1) WAN. ge 0/0 is well connected and i can ping it and the LED light is on but ge 0/1 has failed to come up.Ge0/1 is connected to an IDU and has a public IP address. The LED light also does not light on ge 0/1.Where could the problem be?
View 5 Replies View Relatedhow the ASR1000s are being setup.I am looking at ASR1000s as part of network refresh and was looking at RJ-45 based Gigabit Ethernet ports compatible with the ASR1000s SPA-5X1GE-V2 seems to be an option but they are all SFPs. Are there any options for RJ-45 ones on ASR1000s?
There is an option for the 2 port where one can mix and match SFPs and RJ45 but I was looking for something which is RJ45 only.Are there any options for them available.I know I could get something with FastEthernet type but was looking for the GigabitEthernet type.
Is there a PCI Express 2.0 Gigabit ethernet card [NIC] which i can install in this motherboard where usually one installs NVIDIA graphic cards?
View 4 Replies View RelatedI currently have 2 PCs that are directly connected to each other via a 1Gbs Cat6 connection.I don't currently have a 1Gbs router so what I am doing right now is unhooking this connection and reconnecting both machines to my router when I need internet access. I have ordered some USB Wi-Fi adapters so I can have both machines access the internet that way whilst still use FTP between them on the 1Gbs line.If I were to scrap that idea and get a 1Gbs hub, connect both PCs straight into that, and then also connect the hub to my 100mbits router, would the 2 computers be able to communicate with each other at 1Gbs and then talk to the router at 100mbits, or would the whole network run at 100mbits.I don't really want to have to shell out on a 1Gbs router as I don't need anything else on the network to run at that speed.
View 6 Replies View RelatedPurchased and configured 2951 router based on Telco specs that required T3/DS3 card with coax connection for MPLS. When telco showed up to install DS3 they handed me a UTP copper connection.... Can I use one of the Gigabit ethernet connections on the 2951 as my MPLS interface into the provider's cloud?
View 2 Replies View RelatedWe have a Cisco 7206 VXR Router with NPE-G2. As everybody aware that, It has got 3 x Gigabit Ethernet Ports on this. We would like to add Two more Copper Gigabit Ethernet Interfaces. The Configurator does not show any options to add that.Now we have a doubt that, Does this 7206 VXR support how many Copper Gigabit Ethernet Interface ?. There is no clear answer available in the Data Sheets.
View 2 Replies View RelatedWe have a Cisco 7206 VXR Router with NPE-G2. As everybody aware that, It has got 3 x Gigabit Ethernet Ports on this. We would like to add Two more Copper Gigabit Ethernet Interfaces. The Configurator does not show any options to add that...
Now we have a doubt that, Does this 7206 VXR support how many Copper Gigabit Ethernet Interface ?. There is no clear answer available in the Data Sheets.
I'm going to be upgrading my network (router and network cards etc). I was wondering if there will be any performance difference with the Belkin Fastcat 5e I currently have and CAT6 cables?
View 7 Replies View RelatedI have a Dell Studio running windows 7 sp1. yesterday i was on the internet as normal. Today i was able to connect via my schools wifi, but not my ethernet cable. Device manager shows that my ethernet port should be available.
View 3 Replies View RelatedSo my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
View 13 Replies View RelatedI have the following problem. I bought two TP-LINK TG-3269 gigabit cards, placed them in two computers and connected them directly. On my Ubuntu system I used iperf tool and measured only 95 Mbit/s. It wont go any faster, I tried many times with different settings.
The indicator lamp shows 1000 Mbit/s.
But I currently have a Linksys E3200 I bought in a moment of weakness after an evening of being pissed off at bricking my old WRT610N. (soft bricked, but I'm beyond screwing with it)
There's nothing *wrong* with it, but I am interested in something that either comes preinstalled with DD-WRT, or is well supported (ie easy to install on) by DD-WRT. I plan on selling the E3200 once I find something to replace it.
My requirements:
-Gigabit
-5 GHz (I have a file server/HTPC; I don't want to be limited to gigabit ethernet)
-$150 or less (I know $150 is high, but I figure I'll get close to that for the E3200)
I am moving into an apartment thereafter. I have an HTPC in use, a personal computer for gaming/processing, and my fiancee has an Apple Macbook Pro that she uses quite often. I have an HDHomeRun Dual (2 tuners) for streaming OTA/QSM cable over the network (the HDHomeRun plugs into the network, not a computer). I also have a TV and Blu-Ray player that have ethernet ports.
Currently I use Verizon Fios and their Actiontec MI424WR router, which to my knowledge has gigabet ethernet. When I move I will probably be saddled with Comcast Xfinity Internet, which will supply a cable modem if I want, but no router. The only router I currently own is a Zyxel NBG-419N, which has only 100/10 ethernet ports. My current computers all have gigabit ethernet. For the home theatre components and my HTPC, I plan to pick up a network switch with gigabit ethernet. So my questions are:
1. If I use the Zyxel and the Comcast cable modem, would I be throttling my network speed at the router? I would hate to choke my speed just because one component does not have gigabit ethernet.
2. If I were to upgrade to, say, an Asus RT-N56U, would that make a huge difference on network browsing and throughput speeds?
3. Finally, what kind of cable is needed to maximize discernible speed increase? Cat5, Cat5e, or Cat6?
I was wondering if I could use the CISCO3945 Integrated Gigabit Ethernet WAN ports for routing, I need to enable BGP and I was willing to use one of those ports.
View 2 Replies View RelatedWe are looking for a solution to avoid VPNs to encrypt data between HQ and Bldgs (point-to-multipoint) Gigabit fiber(untrusted media).Is there any cisco's product providing layer2 encryption over Giga fiber?The HQ has a 6509s and remote bldgs have mixed of 3750s,4500s in trunks.
View 2 Replies View RelatedI have a two computer network. Here are the network adapter details of the two computers.
-Realtek RTL8111E Gigabit Ethernet Controller
-Broadcom NetXtreme Gigabit Ethernet
I'm using a CAT5e cable. But it gives only a 10 MB/s file sharing speed. What is the reason for this? (In both the computers under "Local Area Connection Status" it shows 100 Mbps for the speed)
I am looking to get a gigabit ethernet adapter for my minecraft server that is quite big now. It used to run off the motherboard but now since its quite big i thought if i should get a good card. It has to be a pci card and compatible with windows 8
View 3 Replies View RelatedI have the possibility of upgrading a DS3 to Metro Ethernet, Gigabit connection. My dilemma is I have two VTP domains in my network. How can I get two VTP domains over one trunk to a remote site ?
View 0 Replies View RelatedMy new computer has a problem with the on-board gigabit ethernet it keeps dropping network connection every few minutes. Nothing has had any effect. It has been such an annoying problem, I really was hoping to find a fix for this sooner as I know other people have had similar issues. Does anyone have any other ideas because I would like to use the only ethernet connection sometime in the near future. Having to run of an WPN11 netgear usb adapter at the moment.
View 8 Replies View RelatedI have setup an Asus RT n16 with 3 computers that support gigabit ethernet and a media server on one floor. On the other floor I have set up a fast ethernet switch (connected to my asus router) which is connected to several fast ethernet enabled computers.
Would the fast ethernet devices slow down the entire gigabit networking to 100mbps connections on my floor - similar to how a wireless n network running at 300mpbs must slow down to 54mbps when a wireless g device is connected to it?