Cisco Switching/Routing :: 1841 / HWIC-AP-AG-A Not Providing IP Address To Clients
Dec 5, 2012
I have not yet completed my CCNA, however I have managed to configure a 1841 router with 1 x HWIC-ADSL1 and it also has 1 x HWIC-AG-AP-A which is the only part I am unable to get working.
The Wi-Fi (Dot11Radio) config has enabled me to see the SSID from wireless devices, but they never get an IP address. I need them to get the same IP range as the DHCP service I have in there 203.35.10.xxx, there is no option for "IP ADDRESS DHCP" only "IP ADDRESS POOL LAN" Lan is of course my DHCP pool name. however I cannot have the same DHCP pool on both Dot11Radio interfaces.
I know I'm missing one very simple command, but as I've never worked with Radio on Cisco equipment, I am unsure how to fix it.
Then once I get that worked out, I need changing the access from OPEN to WPA or WPA2, etc..
IOS Software on Router is C1841-ADVSECURITYK9-M - Version 12.4(9) T
I can upgrade to a better version of software if needed, I only have a 32mb Flash and 128Mb Ram.
The current Radio Config is:
!
interface Dot11Radio0/1/0
no ip address
no ip redirects
[Code]....
View 1 Replies
ADVERTISEMENT
May 14, 2008
I just recently (and very expensively) purchased a HWIC-1ADSL for my 1841 router.
Unfortunately, it doesn't display in the configuration - nor any lights appear on it for power/link.
My first guess is I need to upgrade my IOS. The current version on my 1841 is 12.4(17). Which appears to be pretty current.
View 9 Replies
View Related
Jan 22, 2012
I have a 1841 deployed as my NAT device towards internet. NAT is setup so that internal addresses can access WWW. I also have some NAT translations opening speciic ports from outside to inside in the form: ip nat inside source static tcp A.B.C.D 443 A.B.C.D 443 extendable.
Now have an outside address/port setup with a public DNS reference and using NAT from outside to get access to the corresponding inside address. It works when being outside the LAN.
Now to the problem: From the LAN side of the router - i cannot access the public name. I can ping it - but my browser dont find the webserver behind the name. Someone told me it should be setup as "local firewall domain" - and i should set this up as "source NAT".
View 12 Replies
View Related
Jan 22, 2013
I have a strange behavior between a WLC 5508 (version 7.0.116.0) and NEXUS7010.
WLC
The WLC is configured in DHCP Bridging Mode (it sends DHCP requests without change)
Nexus
The VLAN interface is configured as follows
interface Vlan501
ip access-group acl-int-vlan501-in-1 in
no ip redirects
ip address 10.12.56.4/21
ip ospf network broadcast
ip router ospf 100 area 10.23.0.0
hsrp 51
Clients can not obtain an IP address intermittently. If I deactivates the ACL when the problem appears(when the client can not obtain an IP@) the probleme is resolved
Note: Before the WLC was connected to Catalyst 6500 and worked properly for 2 years (with same configuration)
I saw this note about differences between DHCP relay on the NEXUS7000/NXOS an Ip helper one the 6500/IOS URL. Do you think the problem may come from the DHCP relay or ACL on the NEXUS.
View 2 Replies
View Related
Sep 4, 2012
I am using cisco 1841 LAN router, I need to block MAC address i have applied the command access-list 1102 deny 0000.0000.0000.0000 mac address..... but it does not work.
View 24 Replies
View Related
Mar 8, 2012
Few days ago I faced a issue in which one of ours 4500 stopped providing poe on some ports in one line card. I called TAC and ran some diagnostics. However, there is a command that I found and it is NOT DOCUMENTED on 4500 reference guide! The command is "diagnostic monitor poe". This command actually detects/recover POE hardware failures! After executing this command, poe start to work again?
View 4 Replies
View Related
Mar 17, 2013
i have a simple router on a stick config which is providing dhcp to a customer SSID. however i don't want employees to stay on it and eat the band width since its open. the lease is set to an hour, is there anyway that i could set it so that once your lease expired it can't be renewed for 4 about 8 hours? I am using a cisco 2600 router in this setup.
View 1 Replies
View Related
Jul 3, 2011
I'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point is that I need to track some external IP address on my primary interface, for examle 8.8.8.8. If it is not reacheable, then router brings up backup connection - 3G. This can be done by using dialer-watcher.Simple.But unfortunately my primary WAN interface is an FastEthernet, which is the coonected to a switch, switch to WAN . There is no dialer-watch commands on it. Thats sad .
One more time :
WAN -> SWITCH -> ROUTER(WITH 3G HWIC and Fa 0/0 connected to switch).
View 4 Replies
View Related
Feb 19, 2012
is there any known issue in configuring multilink ppp using an old WIC-1T and a newer HWIC-1T on the same Cisco 1841 router ?
View 2 Replies
View Related
May 10, 2011
I have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies
View Related
Jan 2, 2012
I'm trying to learn a little about Cisco router setup, since I'm fairly well versed in configuration. I have an 1841 w/ K9 that I'd like to set up as a WAN Router to hot swap if one of ours goes down. I installed a VWIC2-1MFT-T1/E1 MultiFlex card in Slot 1 of the router.
Currently, if I run a "show diag", the VWIC2-1MFT-T1/E1 shows up in Slot 1 but in the configuration I can't see it or configure it. Am I missing an enable or something? I thought I had to declare card type but I can only do that on the existing card, the router doesn't seem to recognize that the card is there in any place other than "show diag".
View 7 Replies
View Related
Aug 19, 2012
I've been given an 1841 with a 3G HWIC card installed to test with. I need to set up some sort of VPN to our ASA, the problem is though these 3G cards get a random public IP, so what options do I have to create a VPN tunnel from this router to the ASA without the 1841 getting a static public IP?
View 3 Replies
View Related
Sep 30, 2010
I am trying tu update the firnmware of a HWIC 3G-GSM within an 1841. What is the correct firmware?
I have tried
K2_0_7_35 and K1_0_2_18 from [URL]
[Code]......
View 6 Replies
View Related
Jun 5, 2011
my office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies
View Related
Jun 5, 2012
Am having an issue with my cisco 1841. I recently brought some IP Publics. Now that i need them i just can't use them, I don't know much about routers but till now have successfully manage to do some stuffs with the router after googling ,OK we already have some other ip publics and when i look at the config file i can see something like this:
View 3 Replies
View Related
Dec 28, 2011
I have a 2811 ISR, a lab unit with almost nothing yet configured other than some IP networks on serial and FE interfaces to ping to other lab routers. And I have one HWIC-4ESW installed, and I amrunning IOS 15.2.I want to set the card as a single routable interface and just have the ports act like switch ports, which I imagine is the default design of these cardsI work a lot with Cisco 891 ISRs so figured it's the same here, assign an IP to interface Vlan1 and all is well. That was wrong, obviously more config is required.It seems there are a lot of differing answers out there, so far none what worked for me. The best looking one I could find said to assign an IP to the Vlan 1 interface, then go to each of the four FE interfaces on the switch module.
View 3 Replies
View Related
Oct 31, 2010
[URL]The Cisco 2811 does not support the HWIC-4T1/E1 module. But, I installed HWIC-4T1/E1 on the 2811 running 124-24.T2.
View 3 Replies
View Related
Jan 24, 2013
Just double-confirm that 2811 is compatible with HWIC-2FE based on your experience? Which IOS is compatible with HWIC-2FE? [URL]
View 3 Replies
View Related
Oct 17, 2012
Just need to verify if HWIC-2T is compatible with the Cisco2800 routers?
View 4 Replies
View Related
Nov 4, 2012
Maybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
View 1 Replies
View Related
Oct 15, 2012
I Have installed HWIC-2T card in my cisco 1921 router but it is not able to detected in router. find the ver of router
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Tue 20-Mar-12
[Code]......
View 8 Replies
View Related
Jul 31, 2012
I have cisco2811 and HWIC-1CE1T1-PRI in the main office are using to connect 10 branches ( 10 ISDN lines) for Data.
I have available channels in the used E1 so I can use them for voice using PVDM2-64 ?
View 3 Replies
View Related
Feb 27, 2012
We have been facing a problem at my company ! We have a Cisco Router 1921 with one HWIC-4ESW in trunking with a RuggedCom switch RSG2100.When I use the GigabitEthernet port to make a trunk, I create 2 sub-interfaces (one for each Vlan) and configure the Port on Switch as Trunk, the inter-VLan routing works with no problem.But now I need to use this configuration using the HWIC-4ESW on Router, and I can't do this work. I try creat interface Vlan for each vlan, and try creating the VLans at Router Vlans database, but no way. At router I enter in interface and try to do the switchport trunk command to add a Vlan, but doesn't work.
View 4 Replies
View Related
Jan 9, 2012
Does Cisco 1921-SEC/K9 support HWIC-4ESW ? I require 4 x 10/100 Ethernet ports
If yes how many ? are there any drawbacks if i use this module instead of a switch?
View 5 Replies
View Related
Nov 18, 2012
We have two cards HWIC-4ESW on router 3845 but we need that the two cards 8 ports conected betwen, if a pc on port 1 can ping a pc conected on port 8 on second card. tis comunication can,t doing a pc on port 1 can,t conected a pc on port 8.
the configuration is the folowing
interface FastEthernet0/0/0
switchport access vlan 100
speed 100
[Code].....
View 1 Replies
View Related
Feb 22, 2012
I am working on a backup system for my WAN. Verizon quoted the HWIC-3G-CDMA-V to work with my Cisco 1721 router. I have a bunch on these routers on a shelf and thought I would use them for the 3G network. Looking at the Cisco web site it does not list the 1721 as being able to work with this HWIC. I thought it might not be listed as the 1700 series are End of life. Whether it will work?
View 3 Replies
View Related
Jan 16, 2008
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
View 4 Replies
View Related
Apr 27, 2012
I have a Cisco 1841 router that is connected to a switch. I have WAN/LAN configured on the router and the switch is handing out internal IP's. The issus that none of the client machines can access the Internet. From within the router console, I am able to ping external domain names, my ISP DNS servers.
Once the client machines picks up an IP they are unable to ping any external domain names or IP's and not even the ISP DNS servers, but they can ping the Cisco router IP. As a note I have tried my ISP DNS servers and as a test Google's DNS servers, but neither will allow access to the Internet.
Below is the current running config:
Building configuration...
Current configuration : 1440 bytes
!
version 12.4
service timestamps debug datetime msec
[Code].....
View 26 Replies
View Related
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
Feb 6, 2012
I'm just getting started with cisco kit so you will have to bare with me.I have a cisco 1841.i have a very wierd issue of routing...i cannot ping and browse through this.
View 3 Replies
View Related
May 31, 2013
I have a problem accessing my wireless router through VLAN sub-interface on my Cisco 1841 router. My hardware:
Cisco Catalyst 2960 switch (192.168.100.4 /24)
Cisco Catalyst 3550 switch (192.168.100.6 /24)
Cisco 1841 router (192.168.100.7 /24)
Asus RT N66U wireless router (192.168.100.2 /24)
Here's my network topology:
I have two VLANs - 10 and 20. 2 DHCP pools are configured on 2 1841's interfaces - 192.168.1.0 /25 and 192.168.1.128/26 with default router sitting on 192.168.1.1 and 192.168.1.129 respectively. No issues with obtaining IP address from any of those pools.Laptop connects to L3 3550 switch (switchport access vlan 10), which, in turn, connects to 1841 router through trunk (with VLANs 10 and 20 allowed).3550 is connected to 2960 through trunk with VLANs 10 and 20 allowed.Wireless router is connected to 2960.I can successfully ping my wireless router and outside world from 1841 from fa0/1 interface, but not from fa0/1.10 or fa0/1.20 sub-interfaces - all packets got dropped. My laptop can obtain IP from both pools (depending on port I connect it to), but can't ping my wireless router and anything beyond it.
I attach my configs:Cisco Catalyst 3550:interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk switchport port-security mac-address sticky speed 100!interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk!interface FastEthernet0/3 switchport access vlan 10 switchport mode access!interface FastEthernet0/4 switchport access vlan 20 switchport mode access!Cisco 1841:
ip dhcp pool Vlan10DHCP network 192.168.1.0 255.255.255.128 default-router 192.168.1.1 dns-server 208.67.220.220 domain-name home.local
!ip dhcp pool Vlan20DHCP network 192.168.1.128 255.255.255.192 default-router 192.168.1.129 dns-server 208.67.220.220 lease 0 12
interface FastEthernet0/1 ip address 192.168.100.7 255.255.255.0 duplex auto speed auto!interface FastEthernet0/1.10 description VLAN10 Sub Interface encapsulation dot1Q 10 ip address 192.168.1.1 255.255.255.128!interface FastEthernet0/1.20 description VLAN20 Sub Interface encapsulation dot1Q 20 ip address 192.168.1.129 255.255.255.192!
Routing table on 1841:
[code]....
View 19 Replies
View Related
Dec 4, 2011
What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies
View Related
Apr 11, 2013
I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?
View 1 Replies
View Related