I have problem with HWIC-3G-GSM configuration. The cellular interface doesn't get IP from ISP.The configured profile is always inactive.cellular 0/2/0 gsm profile create 1 m2m.plusgsm.pl chap plusgsm plusgsm
View 3 Repliesi have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies View RelatedI've been able to activate and configure the Cisco 819 router to connect to Verizon via interface Cellular 0 but when I connect a laptop to the router, int Cell 0 goes down.
Here's a snippet of what happens after I connect a laptop:
rt1#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
[Code].....
I have three routers 811 (independent), and the interface cellular 0 resets in all three.
View 3 Replies View RelatedWe're seeing a strange issue with a Cisco 819 that we're testing out. We are able to ping out over the Cellular interface just fine, but as soon as we plug a device into one of the FastEthernet ports we immediately drop the cell connection. The Cell interface then continues to bounce until we unplug the device. We are intending to setup a VPN tunnel, but we've even stripped all that out for the sake of troubleshooting.
Current configuration : 2832 bytes
!
version 15.2
[Code].....
I have an issue regarding using cellular interface on cisco 881G. The 3G module is Aircard 504. SIMcard is working on other devices, it have obtain IP address from mobile operator. But on cisco881G it doesnt work.
Here is config:
cellular 0 gsm profile create 1 m2m
chat-script 3G "" "ATDT*98*4#" TIMEOUT 30 CONNECT
interface Cellular0
[Code].....
I'm having extreme issues in getting my vpn client to connect to a cisco router with a hwic-3g-hspa cellular interface
I have tested the config remotely by traversing the tunnel I have setup with a cisco vpn client and the client does connect, however when out on the road it doesn't respond, I'm litterally hitting my head against a brick here, everything just seem right I can't explain it.
I have done debugs and there is no sign of life, its as though when the vpn client connects to the router its not responding any way here is my config for the vpn clients part that is.
aaa new-model
!
!
aaa group server radius vpn-client-server-group-1
[Code].....
Can Cisco 881G cellular interface (Modem Firmware Version = K2_0_7_19AP C:/WS/FW) work with r-uim cards? I can't find correct answer in documentation .
View 2 Replies View RelatedI would like to configure the 881G to use both the cellular interface and Fe4 WAN port for internet connectivity.Interface Fe4 is connected to an ADSL router.
I have configure each interface with a default route and weighting:
ip route 0.0.0.0 0.0.0.0 Dialer0 200
ip route 0.0.0.0 0.0.0.0 FastEthernet 4 100
I need to configure Fe4 to get an address as a DHCP client:
interface FastEthernet4
ip address dhcp
no shut
duplex auto
speed auto
How do I remove Fe4 from VLAN1? There is some existing config around VLAN 1:
interface Vlan1
ip address 10.73.0.1 255.255.255.0
ip helper-address 192.168.140.13
ip tcp adjust-mss 1400
no autostate
ip sla 100
icmp-echo 10.64.4.15 source-interface Vlan1
tag 3G Keepalive
frequency 10
Then I guess I need to adjust my Internet-IN ACL to allow broadcasts and UDP 67 and 68?
I just installed two of the HWIC-1GE-SFP cards in the CISCO3945 router but they are not recognized... I don't see any messages on the console output. I don't see them in the "show diag" command. I don't see new ports in the "show run" either... Is there some command I need to put in to activate them? Here is show version of my router:
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code]....
I have a scenario where multiple branches are connected to Head Office via DSL links. The branches are located in differenct exchanges, everyone once in a while ALL branches go down at the exact same time except 3 branches and those 3 branches don't have ATM interface on the router, rather they have external DSL modem, all other branches that face the disconnection (for couple of minutes) have either HWIC-1ADSL-M or HWIC-2SHDSL and the DSL line is directly plugged into the card. [code]
I tried so many solutions like adding "operating-mode auto" command under the subinterface, IOS upgrade, changed dynamic routing protocol from EIGRP to OSPF... Nothing worked, on the logs of the router it just shows "EIGRP neighbor down", at the time of the problem I can't ping any of the affected branches on their WAN ATM interface although it stays physically "up up".Could the problem be a missing command that I need to add under the subinterface? Something maybe related to clocking or timeout or..?Note that hte problem occurs randomly, every few days, sometimes every 10 days, and all branches with ATM interface go down at the exact same time.
I'm having problems to ping through interface atm 0/0/0 which is releated to a card HWIC-2SHDSL . The router I have is a 1941. I dont know what to do. [code]
View 8 Replies View RelatedI have a 3825 router running 12.4t IOS. I installed DSU/CSU part number HWIC-1DSU-T1 in the router and it does not recognize it. Is this the right card for this router? Is there anything I can look at to determine the issue? I think the router only has 32M RAM. Below is a show hardware. Card is still currently installed.
View 2 Replies View RelatedI currently have a Cisco 2621 powering a network at our co-location facility... It's a simple setup and is working well. The colo provides a redundant HSRP uplink, so I have their two uplinks going into a Dell switch. From that Dell switch I have a uplink into FastEthernet0/0 on the 2621, configured with my routing network, and then FastEthernet0/1 gets an address from my block of routable IP. FastEthernet0/1 then plugs into another Dell switch where I have all my servers connected. The servers get public routable IP addresses and use the address on FastEthernet0/1 as their default gateway.
It's time to upgrade off the 2621, so I aquired a Cisco 2811 which has two FE interfaces, as well as a modular HWIC-4ESW switch. My question is, can I get rid of the Dell Switch A in the setup above and just use the internal switch on the 2811 to accomplish the same thing? And I if I did this, would my two uplinks from the colo plug into ports 1 and 2 of that HWIC, and then port 3 would physically connect into FE 0/0? Or can I logically do that via configuration in the Cisco? I'm not sure how all this works and haven't received the new router yet, so I thought I'd get a head start and reach out to the experts.
My second question is unrelated, but each port on the HWIC switch cannot be configured as a network interface right? I'm pretty sure they can't as they aren't considered network interfaces but just thought I'd ask.
I have two HWIC-4T1/E1 in two 2821's I can not for the life of me find software so I can configure them in the routers. I see them in the inventory but don't see them in show ver. I'm assuming that the software is not recognizing them. I've tried a bunch of releases that software advisor says they are supported and am wondering if I'm just doing something wrong.
NAME: "4 port clear channel T1/E1 HWIC on Slot 0 SubSlot 0", DESCR: "4 port clear channel T1/E1 HWIC"PID: HWIC-4T1/E1 , VID: V02 , SN: xxxxxxxxxx
NAME: "Two port T1 voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "Two port T1 voice interface daughtercard"PID: VWIC-2MFT-T1= , VID: 1.0, SN: xxxxxxxxxx
Cisco 2821 (revision 53.51) with 245760K/16384K bytes of memory.Processor board ID xxxxxxxx2 Gigabit Ethernet interfaces2 Channelized/Clear T1/PRI ports1 Virtual Private Network (VPN) ModuleDRAM configuration is 64 bits wide with parity enabled.239K bytes of non-volatile configuration memory.62720K bytes of ATA CompactFlash (Read/Write)
I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan
I have 3945 router using the HWIC-4ESW module.I am not able to see the HSRP configuration commands under these interface.Does this module support HSRP ? If yes , do i need upgrade the IOS of router.
View 1 Replies View RelatedWe have Cisco 2811 router with Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]
View 1 Replies View Relatedmy office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies View RelatedI am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies View RelatedI've been trying to configure the threat-detection scanning-threat shun feature on my ASA5510 running 8.4(2) for some days now. From searching the support community I can see that I'm not the only one having a problem with this feature. The problem I'm having is that after configuring scanning-threat shun, no outside attacking hosts are being shunned. I'm using nmap to simulate a scanning attack. [code]
Is this the expected behavior of scanning-threat shun? If so this feature is of very little use to me as blocking my inside LAN is not my goal. I'm trying to protect my LAN from Internet attack. I can add the except command and exempt my LAN, but this still doesn't fix the problem of outside hosts not being shunned.
Whenever I try to connect Windows XP with Windows 7 I get an error "Local Area Connection" doesn't have a valid IP configuration.I have tried a lot of tutorials and answers on different forums but could not get the answer.
View 2 Replies View RelatedI recently bought a desktop off craigslist, it has been working fine for the past month, but I was about to start up a program and it froze. (was beginning to overheat, so it froze.) So no problem, I reset the computer and when I logged on, the internet had a fashionable yellow ! sign. So I diagnosed it and received the "Local Area Network does not have a valid IP configuration." Now every single computer, wired or not, can access the internet so it is specifically my desktop. I have done literally everything suggested in multiple forums, and nothing I do seems to work. I figure instead of listing everything I have done, I will just assume that I either did it wrong, or was given false information on how to do it, so in case one of those hold true I won't be stuck thinking something didn't work.
-Internet was working
-Computer froze
-Reset Computer
-Internet no longer working on my computer (does on other computers)
-Local Area Network does not have a valid IP configuration
I'm having trouble getting my laptop to connect to the Internet over wi-Fi. If I plug it directly into the router with a cable it works fine. I have 10 other things in my house that connect over wi-Fi just fine, my pc just won't connect.
View 14 Replies View RelatedI know this question seems to come out a lot but I can't seem to fix it. I am a college student and my internet has worked 100% fine until I went home this weekend and came back. It worked this weekend when I brought my computer home and when I came back today it gives me this error when I try to troubleshoot. The only thing that could have changed is when I went home I set my DNS to be openDNS because it makes a huge difference there, but I changed it back when I got here. I don't know if that would matter, but unplugging and restarting are doing nothing.
View 3 Replies View RelatedI am having this problem on my acer intel core i3 laptop I think my Network adapter is corrupt I cannot connect to my Netgear(home) router anymore... I use to be able to troubleshoot/diagnose and fix the error but now it doesn't fix it anymore.Wireless works though...the problem only occurs when I plug a network cable into the NIC... I have tried other network cables and the router at work but it gives me the same error.things I have tried to fix NIC that did not work
cmd- iprelease/renew
changing things in the registry
changing mac address
updating netgear firmware
updating NIC driver
uninstalling the bonjour service
I have tried putting the ip address...dns in manually?i am running on windows 7?
the same thing happened to me Thursday as well. All the laptops and my friends computer(same exact build as my own.) had been able to connect to the internet via wireless/ethernet. However my computer does not. For quite a while it would say the address doesn't have a valid IP, now it thinks there is nothing wrong... I had wiped and reinstalled windows 4 times in a sorry attempt to fix the issue. Also, I had checked the driver for my internet and reinstalled the latest version several times. I've exhausted all the resourses I can think of
View 1 Replies View RelatedI am doing some per-deployment testing with a ASA5585X and noticed that when I feed it a stream of SYN packets on the outside interface the measured traffic rate on the inside interface going out is about 10x the rate of the outside interface going in.
laptop --- ASA --- PC
I send 6k TCP SYN pkt at interface rate from the laptop targeted at PC. No packets are dropped by Ac Ls or policies and can be sniffed at the PC.
Show interface commands show:
sh int inside:
... ...
Traffic Statistics for "inside":
...
1 minute input rate 23 pkt/sec, 1303 bytes/sec
1 minute output rate 4454 pkt/sec, 820757 bytes/sec
sh int outside:
... ...
Traffic Statistics for "outside":
...
1 minute input rate 885 pkt/sec, 70847 bytes/sec
1 minute output rate 7 pkt/sec, 425 bytes/sec
I would expect that if 885 pkt/sec enter the firewall on the outside interface the same amount or less would exit it on the inside...? Why this is not the case? The packet rate is about 5x and the data rate is about 10x greater.
this error is popping up when i'm trying to connect my pc to modem(cisco dpq2160) through cable..."Ethernet doesn't have valid ip configuration".. i have also tried some solutions given in other sites like ipconfig/reset in cmd. it says that there are no settings to reset..
View 1 Replies View RelatedI've recently received this new Cisco 1921 routers with Cisco CP loaded, so it comes up with the annoying change username and password at first access. I've removed all of those files from the flash memory, and rebooted it, and it came up with the proper initial configuration dialog, which is what I wanted. But, whenever I configure the router with a set of basic configuration, like interface, routing, and snmp loggings, and hit wr mem, it doesn't display at all when I do "sh run". It's weird cause when I do sh run | sec rip or any other stuff that I have configured, it shows up , but not in sh run at all.
What's the deal with the new routers? Even sh version doesn't show the config-register or memory allocation details.
xxxxx#sh ver
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled). [code]
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
I have the following zebra.conf on my router box "A":
hostname nuclear-router
password password
enable password password
interface eth0
ip address 192.168.2.1/24
multicast
[code]...
eth0 is connected to a switch and contains the 192.168.2.0/24 range, and A is connected to my WRT54GL "B" (with IP 192.168.1.1, containing 192.168.1.0/24 range, DHCP serves IPs above .100) wirelessly. B is connected directly to my DSL modem.
The problem is that when I specify the default route using the interface name, I can't connect to the internet from A or any hosts behind it - I'm always hit with a "no route to host" error. Name lookup and pinging any local host (even in a different range) or the DSL modem works fine - it's only when going beyond the modem that things stop working. However, when I use the IP of B as the gateway, it works fine. I noticed that route output on A when the default route was specified using the interface alone had only an asterisk in the gateway column. I was under the impression that these approaches should be identical in practice, so though I got it working, I'd like to know what I'm misunderstanding (and/or misconfiguring). Why didn't the default route work when specified using just the interface?
All routers and the modem too have RIP (version 2) enabled, and of course the password isn't really the word "password".