I have configured policies to shape the traffic on the interface of cisco 7206 router. Now my managemet wants to configure these policies on time based ie policy should be applicable during specified time period onle. Is it possible? if yes how to configure it?
View 11 Replieswhat are the values of Bc and Be?interface fast 0/0 traffic-shape group 101 500000
View 11 Replies View RelatedI have a Cisco 2821 with ios Version 12.4(21). On that router I have a WAN link that is 550mbit dual. The interface is 1000FD so i need to shape my output traffic to max 550mbit - otherwise my ISP policing is dropping the traffic.
I've looked at this document url... and i'm trying to use this interface command:traffic-shape rate
But the router wont accept rate value 550000000 that should be 550mbit in bits/s
Is it not possible to shape the traffic to 550mbit on the 2821 router?
I have ASA5510. It's include security plus license.I want to traffic shape to 200Mbps. But , I checked a CCO.CCO said that a shaping limit is 154400000. "Enables traffic shaping, where the average rate argument sets the average rate of traffic in bits per second over a given fixed time period, between 64000 and 154400000. "It's mean shaping limit 154400000 ?Can I shape to 200Mbps ?
View 2 Replies View RelatedRecently I want to apply traffic shape on my ASA5520, but after entering the configure mode of policy-map, I couldnot find the shape command.. If I type the command, the device would notify me that there is no such command.. My version is 8.0(2),PS. Police command is working fine...
View 5 Replies View RelatedI have a asa 5510 with 8.x software and I want to reserve (i mean RESERVE not PRIORITIZE) traffic based on protocol, like if I have a 10Mbit I want to :
- give 3 Mb for smtp
- give 5 Mb to http/s whatever
- 2 Mb for other stuff.
Of course QOS won't do that, can you do that with ASA?
i have a cisco router 7206 ,when i create subinterface with ip , the router hangs , and all interfaces are down ,i just remove interface gi0/1 and plug it again, what is the relaiton between subinterfaces and hanging routers> the problem occurred when i configured sub-interface on GI0/2. [code]
View 13 Replies View RelatedI have a 7206 VXR router between a several Mikrotik routers on our backbone. We have the Mikrotiks on both sides of the CIsco 7206VXR setup for MPLS/VPLS. I need to simply setup the 7206 to pass the MPLS/VPLS tagged packets to the next router on the link. We are using OSPF as the routing protocol. I am told by our Mikrotik guy that I just need to enable LDP and VPLS tunnels 4:0 on the 2 gig interfaces on the 7206VXR to let it pass the MPLS/VPLS traffic. It sounds simple but I'm not sure how to do this.
Any commands I need to imput to allow this router to pass this MPLS/VPLS traffic.
I want to configure multilink between two Cisco 7206 routers POS interfacesafter configuring both sides.Router 1interface Multilink5 ip address. [code]. I can see both sides through show cdp, also ospf process goes to FULL stateBut traffic is not flow between interfaces, and i can not even ping router's own ip address.When i delete network statement from ospf process, i can ping router's own interface and both routers can ping each other.
View 1 Replies View RelatedOn an AIRONET 600 AP (officeExtend) with the remote LAN interface is configured to use 802.1x authentication:If a Cisco IP Phone is connected, 801.x authentication challenges for credentials. The AP does not seem to have a way to detect that this is an IP Phone and to skip the challenge (as Cisco switches/routers would do) Is there any way around this? Can the remote LAN interface be configured to skip authentication for IP Phone and only authenticate PCs etc..?
View 5 Replies View RelatedI currently have a Cisco 2621 powering a network at our co-location facility... It's a simple setup and is working well. The colo provides a redundant HSRP uplink, so I have their two uplinks going into a Dell switch. From that Dell switch I have a uplink into FastEthernet0/0 on the 2621, configured with my routing network, and then FastEthernet0/1 gets an address from my block of routable IP. FastEthernet0/1 then plugs into another Dell switch where I have all my servers connected. The servers get public routable IP addresses and use the address on FastEthernet0/1 as their default gateway.
It's time to upgrade off the 2621, so I aquired a Cisco 2811 which has two FE interfaces, as well as a modular HWIC-4ESW switch. My question is, can I get rid of the Dell Switch A in the setup above and just use the internal switch on the 2811 to accomplish the same thing? And I if I did this, would my two uplinks from the colo plug into ports 1 and 2 of that HWIC, and then port 3 would physically connect into FE 0/0? Or can I logically do that via configuration in the Cisco? I'm not sure how all this works and haven't received the new router yet, so I thought I'd get a head start and reach out to the experts.
My second question is unrelated, but each port on the HWIC switch cannot be configured as a network interface right? I'm pretty sure they can't as they aren't considered network interfaces but just thought I'd ask.
we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
I have Pix 501 firewall and I'm just configuring the device for "Email Server" to allowing POP/SMTP.
Inside Interface Address: 132.147.162.14/255.255.0.0
Outside Interface Address: ISP provided IP address
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80
Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53
Pix(config)#access-group outbound in interface inside
we have a Cisco 3825 router which does not work well with a DSL modem(ISP provided). I have configured the Gi0/0 port of the router to plug into this DSL modem but it does not ping to the ISP gateway. If we do a shut/no shut on the interface then it work fine for about 30 secs. Sometimes even for 1 hr. Then the packets drop and we cannot pass any traffic through this interface.
Now, if the ISP connection is terminated on a computer it works fine. It works fine without dropping any packet.I have tried various options like using a straight/cross cable. I have tried to configure the interface negotiation for 100/full, 100/half, auto/auto and almost all the options.I have also tried to interconnect the devices using a L2 device like a HUB. Nothing works.
Initially we had a rv110w in place and had problems with the port forwarding stopping a few times a day so we replaced with with a RV180W. Now port forwarding appears to be staying up, however I have a new problem. We host a web page, for some reason when an internal user points the url to the web page it resolves to the web interface of the Router and not the expected web page. If you are outside of the network it resolves to the correct web page. I am not sure why this is happening as it didn't happen with the RV110W or the PIX before that.
View 2 Replies View RelatedI have two 1800 routers running VRRP. Also I have two sub interface configured on both router and both router connected to swith through thunk link. My goal is to limit inbound traffic to 3Mbps for both VLANs on router's inside interface which is connected to switch.
View 1 Replies View RelatedI am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
View 3 Replies View Relateddetermine whether I have QoS properly setup on my router, and why the rules do not appear to be taking effect.ISSUE We have a couple of laptops, smartphones, and a Wii on our home network. One device, my roommate's laptop, is a real bandwidth hog. It's connected (via internet, not VPN) to a work server and is frequently downloading and syncing large datafiles and media files.Unfortunately, when that laptop is downloading the other devices either cannot connect to the internet without timing out, or is VERY slow, for example pulling up websites like google.com. When that laptop is offline, everything works fine. It seemed like enabling QoS would resolve our problem.\
SETUPLinksys E1000, latest firmware (v2.1.02), using WPA2-Personal security.
We first tried enabling QoS and setting the MAC address of the downloading laptop to "low" priority and all others to "medium". No luck - the downloading laptop still seems to be hoarding the bandwidth.We also tried adding the download application to the list and setting the port to "low". Still no luck.We added a new application called "web" and set port 80-81 to "high", but that didn't work.We then disabled WMM support. No dice. The other devices still can't connect while my roommatte's laptop is syncing.We've fiddled around with the settings a bit, but no matter what, it looks like the QoS rules are not being applied.And is it acceptable to have multiple categories (MAC and application) in the QoS rules?
I have an E4200 v1 wireless router, F/W 1.0.04.
Article ID 4041 [URL] says I can have up to 10 Internet Access Policies but the web based GUI has a pull down with only 5 possible.
Is 10 policies possible? If so, how?
I need to upload IOS c7200-advipservicesk9-mz.124-15.T16.binin 7206 NPE 400 router , As per cisco recommendation router should have DRAM : 256 MB ; Flash : 64I think my router contain only DRAM= 128 MB but not sure.
how much DRAM & Flash it contains.
Router1#sh versionCisco Internetwork Operating System SoftwareIOS (tm) 7200 Software (C7200-IK9S-M), Version 12.3(1a), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2003 by cisco Systems, Inc.Compiled Thu 05-Jun-03 20:58 by dchihImage text-base: 0x60008954, data-base: 0x61E0C000
[Code].....
I'm getting below error on 7206VXR (NPE-G1) with IOS "c7200-js-mz.124-3i.bin".Attempt to use contiguous buffer as scattered.[code]
View 3 Replies View RelatedI am quite new to WCS and preparing a demo for a client. I am also using WLC2125 with LAP1252s for this setup. Is it possible to modify the shape of the heatmaps of the APs? I know how to regulate TX power of the radios and all works great but how can I controll RF leakage outside the perimiter of the building? Is it possible to controll the RF so that it will not be going outside and same time giving a good coverage inside?
View 1 Replies View RelatedI have a scenario with a Cisco 6506 and a 7206. The 6506 is running BGP and peers with our data center router. The 7206 is a stub router off the 6506 and is used as an edge router for customer T1 circuits. I want to use OSPF between the routers to exchange connected and static routes. The problem I have is that static BGP null routes on the 6506 are overriding the OSPF routes being received from the 7206. Example: The 6506 is advertising a class C network 192.168.1.0/24 to our data center. The 6506 does not utilize the 192.168.1.0/24 network. It is only used on the 7206 for customer T1 circuits and is carved up into /29 subnets. So the 6506 has a static route: ip route 192.168.1.0 255.255.255.0 null 0. Today the routing is accomplished with static routes on the 6506 for the 192.168.1.0 networks on the 7206. Using OSPF the 7206 advertises /29 links back to the 6506, but when I withdraw one of the /29 static routes from the 6506, the /24 null route takes precedence over the more specific /29 routes and the traffic is black-holed on the 6506. how can I get the OSPF routes to look preferable to the /24 null route on the 6506?
View 7 Replies View RelatedWe have a router (7206) which connected to client device in /30 IP segment, but this device is a switch which connected to many more devices. Doing packet capture on our router interface unravel many ARP requests whcih comes from the client switch. Is there any feature or command which we can stop this?
View 4 Replies View RelatedTried setting up a Shape Policy and it states its invalid. Worked fine on my 5520, just curious to know why its coming as invalid now
ciscoasa(config-pmap-c)# shape
^
ERROR: % Invalid input detected at '^' marker.
ciscoasa(config-pmap-c)# shape ?
ERROR: % Unrecognized command
I am working at a client site that is an MPLS customer. The customer has an MPLS circuit that runs between their Main HQ and their Disaster Recovery site. I have been asked to analyze and report as well on the way the Qos Policy is written, and to provide any recommendations on how they can improve performance.There is a statement within the Qos Policy as it exists at each end on the 3825 routers. The statement is called "shape average percent". Here is the policy from one side:
policy-map QoS
class COS2_traffic
set dscp af31
shape average percent 12
bandwidth percent 13
[code]....
What does this statement mean and how is it different than the the "bandwidth percent" statement?
We currently "need" to shape certain services very specifically....we curently do this via routers for CE's (881's etc) i.e. 10Mb service, we need:
-class class-default
-shape average 9800000 40000 0
Some of our clients want to run firewalls as CE's that are unable to shape to this degree, so we are wanting to put an inexpensive switch in front of their CE to do the shaping for them(L2 - either per-port or per-vlan)...the ME3400 looks ok, but is quite expensive.
We have a 7206 router which acts as a MPLS Hub router for around 100+ remote locations. Bandwidh at mpls hub(terminated on this router) is 50 Mbps.
We have noticed that Memory utilization in this router gradually increases and when it reaches 100% this router hangs. It happence in frequesncy of 10 days and we have to restart the router when memory is 100%.
CPU utilization is normal i.e below 20%, WAN bandwidth will never cross 30mbps.
We are running OSPF on this router
We could not able to upload an IOS for 7206 router with NPE-150 via xmodem as there was no image available in flash it is in rommon mode. But same can be done in 1841. So how to upload an image in flah for 7206 via xmodem.Where the IOS will be stored in 7206, wethet in flash or NPE. If it's in flash what for NPE used other than for routing engine capabilities.
View 3 Replies View RelatedI will upgrade ios image to router 7206vxr, only have doubts, is necesary upgrade
View 2 Replies View RelatedThere is a remote server that downloads info from a server here at HQ. When the dowloads start the rxload on the S0/0/0 interface jumps to 98 percent or so; rxload 250/255. I needed to limit the bandwidth utilization between the servers, so I added the below line to the LAN interface on the remote router.By adding the command, it reduced the download utilization -which is what I wanted.
access-list 185 permit ip host 10.6.27.1 any
!
int f0/0
traffic-shape group 185 10000 8000 8000 1000
Question:How would applying this to the LAN interface cause the download utilization (Coming from s0/0/0) to decrease?
i want to monitor interface traffic in/out by eem and the if the values is overer than some value i will change the policy. for example my router is 2821 is have 2 fastEthernet port , i want to monitor the traffic on fasE1/0 if traffic over than 80Mbps i will change some configuration ( example: change next-hop on static route) for via traffic to interface fasE1/1 for reduce the traffic on interface fasE1/0?
View 6 Replies View RelatedI want to allow ICMP traffic on ASA 5510 from LAN interface to DMZ. I've permit any traffic and added ICMP to the inspestion list also but still there is problem. Belos is the configuration. The image is asa822-k8.bin
:
ASA Version 8.2(2)
!
hostname fw-01
names
!
interface Ethernet0/0
[code]....