Cisco Switching/Routing :: Inexpensive 881 Switch That Can Shape?
May 15, 2013
We currently "need" to shape certain services very specifically....we curently do this via routers for CE's (881's etc) i.e. 10Mb service, we need:
-class class-default
-shape average 9800000 40000 0
Some of our clients want to run firewalls as CE's that are unable to shape to this degree, so we are wanting to put an inexpensive switch in front of their CE to do the shaping for them(L2 - either per-port or per-vlan)...the ME3400 looks ok, but is quite expensive.
View 6 Replies
ADVERTISEMENT
Nov 12, 2012
I have been reading for awhile now on all the Cisco forums on the 3560 and shaping egress traffic but I wanted to verify my thoughts on this. I have 3560 that connects to the ISP that is policing at 10Megs, I want to shape my egress traffic going to the ISP, I do not want to provided QOS to any specific traffic type but only shape all traffic outbound. Will my config below shape "all" egress traffic going to the ISP on the 3560, on a port that is physically connect at 100Meg Full duplex?
int gi0/1
srr-queue bandwidth shape 40 40 40 40
I gathered these numbers using the formula of 100* 1/weight, which would equal 2.5 and if each queue has 2.5 meg that would = 10Meg. However another concern is that I don't think I have the full 100Meg on the interface to use (correct?)
View 3 Replies
View Related
Dec 5, 2012
We need to collect some BW usage charts for our ASA interfaces. We don't have the expensive Network monitoring software, and we are a very small shop. I only need BW and data-drop graphs.
View 3 Replies
View Related
Jan 15, 2011
Any cheap wireless adapter for windows 7? Like around $20 and usb interface? I have a 2wire router that was setup by at&t (not sure if I can change it cus tv and everything goes through one box), and they threw in a 2wire wireless adapter, but it sucks. It randomly drops signal and doesn't get a very strong signal even though the router is 20 feet away. I had a cheap trendnet adapter for my xp machine but couldn't find drivers for windows 7.Also do you think the reason it drops is the adapter or possible the router? Cus I watch netflix through nintendo wii which is in the same room as the router and that never has any issues and gets great bandwidth. My laptop with an internal card never seems to have much trouble either... pretty sure I should replace the adapter.
View 1 Replies
View Related
Sep 10, 2012
Our company is starting to open a lot of small mpls sites across the nation. By small I mean less than 10 users, voip, 1 dc, that's it. Instead of getting the usual 2901+2960 combo, I'm interested in finding less expensive solutions. Maybe an L3 switch like a 3750? These are temporary sites so management is fine with looking into used, non smartnet covered gear?
View 7 Replies
View Related
Apr 23, 2012
I need 10gigbit uplink for this switch. What are the other devices that i need order along with this device.And what is the diff between X2-10GB-LR= and CVR-X2-SFP.if i take CVR-X2-SFP, in future how can i upgrade from one gig to 10 gig?for current use i need 10gig support required. so what are all the other devices that i need to order.Fiber multimode and distance 15Mt only.
View 2 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Feb 19, 2012
I'm looking for a good yet inexpensive firewall for a small business (12 people in the office, and 12 others who are out and about all day). I also would to monitor internet traffic too. Currently using FortiGate50B, and it expires in 90 or so days,
View 19 Replies
View Related
Dec 28, 2008
what is the use of no switch port command in L3 switch?
View 7 Replies
View Related
Nov 18, 2012
I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies
View Related
Nov 20, 2009
I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies
View Related
Mar 20, 2011
I am quite new to WCS and preparing a demo for a client. I am also using WLC2125 with LAP1252s for this setup. Is it possible to modify the shape of the heatmaps of the APs? I know how to regulate TX power of the radios and all works great but how can I controll RF leakage outside the perimiter of the building? Is it possible to controll the RF so that it will not be going outside and same time giving a good coverage inside?
View 1 Replies
View Related
Mar 8, 2012
I have a Cisco 2821 with ios Version 12.4(21). On that router I have a WAN link that is 550mbit dual. The interface is 1000FD so i need to shape my output traffic to max 550mbit - otherwise my ISP policing is dropping the traffic.
I've looked at this document url... and i'm trying to use this interface command:traffic-shape rate
But the router wont accept rate value 550000000 that should be 550mbit in bits/s
Is it not possible to shape the traffic to 550mbit on the 2821 router?
View 10 Replies
View Related
Apr 21, 2012
what are the values of Bc and Be?interface fast 0/0 traffic-shape group 101 500000
View 11 Replies
View Related
May 30, 2012
I have ASA5510. It's include security plus license.I want to traffic shape to 200Mbps. But , I checked a CCO.CCO said that a shaping limit is 154400000. "Enables traffic shaping, where the average rate argument sets the average rate of traffic in bits per second over a given fixed time period, between 64000 and 154400000. "It's mean shaping limit 154400000 ?Can I shape to 200Mbps ?
View 2 Replies
View Related
Dec 21, 2011
Recently I want to apply traffic shape on my ASA5520, but after entering the configure mode of policy-map, I couldnot find the shape command.. If I type the command, the device would notify me that there is no such command.. My version is 8.0(2),PS. Police command is working fine...
View 5 Replies
View Related
Jul 9, 2012
Tried setting up a Shape Policy and it states its invalid. Worked fine on my 5520, just curious to know why its coming as invalid now
ciscoasa(config-pmap-c)# shape
^
ERROR: % Invalid input detected at '^' marker.
ciscoasa(config-pmap-c)# shape ?
ERROR: % Unrecognized command
View 11 Replies
View Related
Jan 3, 2010
I am working at a client site that is an MPLS customer. The customer has an MPLS circuit that runs between their Main HQ and their Disaster Recovery site. I have been asked to analyze and report as well on the way the Qos Policy is written, and to provide any recommendations on how they can improve performance.There is a statement within the Qos Policy as it exists at each end on the 3825 routers. The statement is called "shape average percent". Here is the policy from one side:
policy-map QoS
class COS2_traffic
set dscp af31
shape average percent 12
bandwidth percent 13
[code]....
What does this statement mean and how is it different than the the "bandwidth percent" statement?
View 2 Replies
View Related
Jun 25, 2012
I have a asa 5510 with 8.x software and I want to reserve (i mean RESERVE not PRIORITIZE) traffic based on protocol, like if I have a 10Mbit I want to :
- give 3 Mb for smtp
- give 5 Mb to http/s whatever
- 2 Mb for other stuff.
Of course QOS won't do that, can you do that with ASA?
View 1 Replies
View Related
Dec 8, 2011
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
View 4 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
Jul 27, 2012
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
View 4 Replies
View Related
Feb 5, 2012
I recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
View 11 Replies
View Related
May 8, 2012
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
View 9 Replies
View Related
Apr 16, 2012
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies
View Related
Jun 4, 2013
I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
View 3 Replies
View Related
Mar 11, 2012
I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
View 4 Replies
View Related
May 21, 2013
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
View 1 Replies
View Related
May 28, 2013
Two Cisco C2960G Switches connected with each other using an EtherChannel Trunk Ports.IOS Image has been upgraded to c2960-lanbasek9-mz. 122- 58.SE2.bin.The global command "sdm prefer lanbase-routing" has been executed to set the default template to "lanbase-routing".The global command "ip routing" has been executed to enable the ip routing.An IP route has been configured in each switch to point to each other for the static routing purpose (Please see the 2 attached configuration files) The hosts in VLAN 111 and VLAN 110 are not able to see each other even the ip static routes have been configured.May be I have misconfigured some settings but not sure what's the actual problem.
View 11 Replies
View Related
May 22, 2013
my company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
View 10 Replies
View Related
Dec 18, 2012
You can set the ME3400 switch set to the Routing SDM template such that it support PBR. That is done in the ASICs, right? Because if it is done in software the switch could quickly become overwhelmed.
View 2 Replies
View Related
Apr 26, 2012
I have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....
View 11 Replies
View Related
Nov 16, 2011
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies
View Related
