We could not able to upload an IOS for 7206 router with NPE-150 via xmodem as there was no image available in flash it is in rommon mode. But same can be done in 1841. So how to upload an image in flah for 7206 via xmodem.Where the IOS will be stored in 7206, wethet in flash or NPE. If it's in flash what for NPE used other than for routing engine capabilities.
View 3 RepliesI need to upload IOS c7200-advipservicesk9-mz.124-15.T16.binin 7206 NPE 400 router , As per cisco recommendation router should have DRAM : 256 MB ; Flash : 64I think my router contain only DRAM= 128 MB but not sure.
how much DRAM & Flash it contains.
Router1#sh versionCisco Internetwork Operating System SoftwareIOS (tm) 7200 Software (C7200-IK9S-M), Version 12.3(1a), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2003 by cisco Systems, Inc.Compiled Thu 05-Jun-03 20:58 by dchihImage text-base: 0x60008954, data-base: 0x61E0C000
[Code].....
Bought a used 2950 for CCNA labs. I have no IOS and cannot get a successful transfer via xmodem. In ROMmon after the transfer completes text shows up as gibberish, commands seem to work. Text is normal after I reconnect. Dir flash: doesn't show any sys image, only a -rwx file. I have tried various IOS versions. This was purchased used, so it's possible it isn't working. This is my first time configuring a switch, I might have missed something simple.
View 5 Replies View RelatedI'm trying to upload the 5-2-0-26-4.tar.gpg patch to our ACS and so far have been unsucessfull. I keep getting the "please verify the patch bundle is valid".
When I download the 5-2-0-26-4.tar.gpg file, for some reason the download always comes down from Cisco as 5-2-0-26-4.tar.tar. I've renambed the file to 5-2-0-26-4.tar.gpg and verified the MD5.
I have two Cisco WLC 5508 controllers that I'm trying to set-up for our new corporate WLAN. I've gone through most of the configuration fine but have ran into an issue uploading a signed certificate to one of my controllers. I should point out that I have managed to upload the certificate successfully to one of the controllers, I just can't seem to upload it to the second.The issue is as follows:
- I've logged into the controller, gone to Security -> Web Auth -> Certificate -> Download Certificate
- I've specified my tftp server details and selected apply
- the process begins and I can see through my tftp client that the controller is attempting to copy and install the certificate
- The controller tries to install the certificate but fails, reporting the same
So apparently the 3600 series do not support the tftpdnld to upgrade your ISO when you upgrade your flash. You have to use the Xmodem transfer as described here: Xmodem Console Download Procedure Using ROMmon [URL]. everything is going great but it is going to take another 3 hours.
Now when i installed the new flash at bootup it said the "device does not contain a valid magic number" now that is just because the flash is not formatting correctly and downloading the new flash file automatically formats the flash setup?
I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies View RelatedI'm getting below error on 7206VXR (NPE-G1) with IOS "c7200-js-mz.124-3i.bin".Attempt to use contiguous buffer as scattered.[code]
View 3 Replies View RelatedI have a scenario with a Cisco 6506 and a 7206. The 6506 is running BGP and peers with our data center router. The 7206 is a stub router off the 6506 and is used as an edge router for customer T1 circuits. I want to use OSPF between the routers to exchange connected and static routes. The problem I have is that static BGP null routes on the 6506 are overriding the OSPF routes being received from the 7206. Example: The 6506 is advertising a class C network 192.168.1.0/24 to our data center. The 6506 does not utilize the 192.168.1.0/24 network. It is only used on the 7206 for customer T1 circuits and is carved up into /29 subnets. So the 6506 has a static route: ip route 192.168.1.0 255.255.255.0 null 0. Today the routing is accomplished with static routes on the 6506 for the 192.168.1.0 networks on the 7206. Using OSPF the 7206 advertises /29 links back to the 6506, but when I withdraw one of the /29 static routes from the 6506, the /24 null route takes precedence over the more specific /29 routes and the traffic is black-holed on the 6506. how can I get the OSPF routes to look preferable to the /24 null route on the 6506?
View 7 Replies View RelatedWe have a router (7206) which connected to client device in /30 IP segment, but this device is a switch which connected to many more devices. Doing packet capture on our router interface unravel many ARP requests whcih comes from the client switch. Is there any feature or command which we can stop this?
View 4 Replies View RelatedWe have a 7206 router which acts as a MPLS Hub router for around 100+ remote locations. Bandwidh at mpls hub(terminated on this router) is 50 Mbps.
We have noticed that Memory utilization in this router gradually increases and when it reaches 100% this router hangs. It happence in frequesncy of 10 days and we have to restart the router when memory is 100%.
CPU utilization is normal i.e below 20%, WAN bandwidth will never cross 30mbps.
We are running OSPF on this router
i have a cisco router 7206 ,when i create subinterface with ip , the router hangs , and all interfaces are down ,i just remove interface gi0/1 and plug it again, what is the relaiton between subinterfaces and hanging routers> the problem occurred when i configured sub-interface on GI0/2. [code]
View 13 Replies View RelatedI will upgrade ios image to router 7206vxr, only have doubts, is necesary upgrade
View 2 Replies View RelatedI have a Cisco 7206-CH router and the power supply have been stopped working. I am very confused if the new " PWR-7200-ACE= " power supply can be used with this model which have been announced as end of sale and support from 2007.
View 3 Replies View RelatedWhenever I want to turn off the ip cache flow and enter command "no ip flow egress" on a router interface, the router will self reboot and returned with the error message - System returned to ROM by bus error at PC message in the show version ouput.
I tried on two different routers below here and both also undergoing a cold restart when I key in the command "no ip flow egress" on the said interface
1) Cisco 7206 running IOS 12.4(1c)
interface GigabitEthernet0/1
ip address 10.20.10.2 255.255.255.0
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/1 and the router self restarted and return the message Router uptime is 3 minutes System returned to ROM by bus error at PC 0x606D48FC,address 0x0
2) Cisco 3845 running IOS 12.4(3e)
interface GigabitEthernet0/0
ip address 10.20.20.2 255.255.255.0
ip nbar protocol-discovery
ip flow egress
duplex auto
speed auto
end
when I key in "no ip flow egress" under int gi0/0 and the router self restarted and return the message
Router uptime is 3 minutes System returned to ROM by bus error at PC 0x6007EBE0, address 0x0
I have configured policies to shape the traffic on the interface of cisco 7206 router. Now my managemet wants to configure these policies on time based ie policy should be applicable during specified time period onle. Is it possible? if yes how to configure it?
View 11 Replies View RelatedI just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
Application is that need to configure the VOIP with the existing Frame relay network ,where VOFR command is not shown in the router when type yhe command router config#dial-peer voice 123 need vofr On the 3945 router where in the router it is not accepting the above command,
View 8 Replies View RelatedI have a cisco E1000 router and I am unable to upload files, everything else seems to be working fine
View 2 Replies View RelatedI have a laptop and a PC, both connected to the same router, connected to a Time Warner Road Runner cable modem. The laptop works fine whether it is in wireless or wired mode. The PC does not have wireless. When the PC is connected to the router, it's download speed is OK but I have zero upload speed - which of course kills my ability to do almost any online or even LAN task, including browsing and file transferring over LAN.
When I plug directly into the modem, bypassing the Belkin, the PC connection works just fine. It only encounters errors when going through the router, but every other computer in the household works fine through the router (3 laptops, work great either wired or wireless using same cables and ports as the PC). The PC worked fine in my old apartment with a different router, but as soon as I got to this one, nothing.Both comp's have WinXP Home Edition. The PC has a Realtek onboard NIC, called PCIe GBE Family Controller NIC in Device Manager. Have tried uninstalling and reinstalling it, and using multiple driver versions, to no avail. The Ethernet cable is known working.
I have a switch connected from the internet outtake in my apartment.This switch gives internet to two, or sometimes three computers, by cable.To get wireless I have a DLINK-615 connected after the switch.This solution works flawless for some time, just after the router is started or reset. If I go to speedtest.net both the upload and the download works flawless.However, after around half an hour it's virtually impossible to upload, which gives heavy lag in programs like skype and games. If you try to speedtest.net now the download is still fine, but the upload gives a result of 0.1mb/sec after trying to even start the test for 3-4 minutes.Router giving up upload completely
I've tried to change the IP in the router to prevent a conflict between it and the switch. The problem is still there whatever IP I choose though, I simply have no upload.I've also tried to disable the DHCP, mess with the MTU and to enable the Access Point mode with no result.
I want to download the iOS update to my Cisco 2800 Series Routers and Cisco Catalyst 2960 Series Switches and leave them there till im ready to install them. Is this possible?
View 1 Replies View RelatedI have a RCA modem from comcast high speed internet.Also have a Linksys Cisco Wireless-N Gigabit Router model # WRT310N V2. When I connect the internet directly into the computer, I get download speed up to 21.07 mbps and upload speed of 3.07. When I connect through the router download speed 1.31mbps and upload speed of 1.01.I have no clue how to make changes to the router.
View 19 Replies View RelatedI have a laptop and a PC, both connected to the same router, connected to a Time Warner Road Runner cable modem. The laptop works fine whether it is in wireless or wired mode. The PC does not have wireless. When the PC is connected to the router, it's download speed is OK but I have zero upload speed - which of course kills my ability to do almost any online or even LAN task, including browsing and file transferring over LAN.When I plug directly into the modem, bypassing the Belkin, the PC connection works just fine. It only encounters errors when going through the router, but every other computer in the household works fine through the router (3 laptops, work great either wired or wireless using same cables and ports as the PC). The PC worked fine in my old apartment with a different router, but as soon as I got to this one, nothing.
Both comp's have WinXP Home Edition. The PC has a Realtek onboard NIC, called PCIe GBE Family NIC in Device Manager. Have tried uninstalling and reinstalling it, and using multiple driver versions, to no avail. The Ethernet cable is known working. The router is a Belkin F5D9230-4 Wireless G Plus MIMO Router with fully updated firmware.All my firewalls are turned off, including that of the router.Everything is up to date, I have done full virus and malware scans, power cycled everything, and I just cannot solve this problem.
I am using filezilla (ftp client) to upload to file server as well as other sites including free host and 000webhost, on large files my upload fail near the end,This does not happen if I bypass my e200 router, so it must be something about the the e2000 that is causing the failures.
View 2 Replies View RelatedI've hooked up an external usb drive to my EA4500 and i have enabled the FTP server so a friend of mine can download from the drive. Thing is though, that i want to limit the the upload of the ftp server so it wont be using the 100% of my ISP's upload bandwidth. How can i do that? I have the latest cisco connect cloud firmware and i go to Media Prioritization>Settings and set the upload to what i want, but he still downloads with the max speed of my upload..
View 6 Replies View RelatedI have working internet behind cisco 2811 on all vlans however upload speed is very slow and ftp server download is slow and times out, previously when directly connected to modem/router was fine? This is router config below:
Current configuration : 2229 bytes
!
! Last configuration change at 02:21:18 UTC Tue Mar 12 2013
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
[code]....
Since upgrading some of computers in my LAN to Windows 7 they all experience upload issues. I have narrowed it down to CBAC inspection on my Cisco 1711 router, I am running IOS 12.3 I have a simple CBAC inspection set for TCP/UDP only without any application-specific inspects. Download works fine however upload does not seem to work atl all- unless I disable the ip inspection. It is all working fine for any Windows XP but not for Windows 7 machines. Is this a known issue, I am not sure how I can go about this - I don't want to build ACLs now for outside interface and disable stateful inspection mechanisms because CBAC has been working fine for me until recently.
View 7 Replies View RelatedI am getting very slow download speeds on my wireless router (Linksys model#WRT160N). I measured it on speedtest.net. with my ASUS laptop, ASUS Transformer Prime tablet, and 2 Ipod touches. All similar speeds.
Download avg: 1.30 Mbps
upload avg: 6.20 Mbps
I measured my desktop speed that is hardwired through the router to the modem.
Download avg: 30.00 Mbps
upload ave: 6.20 Mbps
I have scanned all the wireless connection in my area and found them to occupy channels 1, 6, 11. I tried changing my channels one at a time for all 11 channels. Some did a little better than others but not a lot.Also, if I by a dual channel router, can all wireless devices pick up on the 5GHz spectrim and if some, could this alleviate some interference?Is it possible that my router is going bad and a new single channel 2.4 GHz router will be fine?
I cannot upload files through http (e-mail attachments, send images to Facebook, send file to virustotal.com) with Linksys WRT600N router. When I remove connection cable from router and place directly in a computer, everything works just fine. I am using last firmware upgrade.
View 2 Replies View RelatedI upgraded my old router to a Linksys E1200 about 2 months ago. Like others with Comcast, I now have a lot slower internet speeds. I've updated everything, disabled WMM. I'm still getting slow speeds. My download speed is 3.12, which is not that bad for me. However, my upload is just below 1.
View 7 Replies View RelatedI am using a Cisco RVS 4000 to test a new 10M/10M internet connection. I'm having a small problem performing the ISP's speed test (speedtest.cavtel.net). The download test consistently gives me 10Mbit/s, full speed for the connection, however the upload speed is usually about 5.5 Mbit/s. My ISP has been onsite and has checked the lines and tested directly, and we have determined that if connected directly we can test to full upload speeds, but when the RVS is connected, we cannot get full speed.
We've tried different cables, reseting to factory defaults, updating firmware, changing port settings, and toggling most of the other setting on the router. Some settings do have a minor effect on the upload speed, but nothing that gets me back up to 10Mbit/s.
I did notice that there appears to be no way to set speed and negotiation settings on the WAN port. Perhaps I am missing it, because that seems like a possible culprit.
Otherwise, the only only thing I can think of is a warranty return to determine if the unit itself is defective.
I Have BT Infinity and they are pushing 70mbps to my house ....i bought an EA6500 and i had real bad internet speed but amazing conection speed with my BT Home HUB3 ... 23Mbps with Cisco EA6500 and 68Mbps with my BT Home Hub3. I found out it was the Media Prioritization so just to be safe i reset my factory settings and made sure it was turned off. Just like magic i get the same now as the BT Home HUB3 .
View 1 Replies View Related