D-Link DIR-615 :: Router Giving Up Upload Completely
Mar 4, 2011
I have a switch connected from the internet outtake in my apartment.This switch gives internet to two, or sometimes three computers, by cable.To get wireless I have a DLINK-615 connected after the switch.This solution works flawless for some time, just after the router is started or reset. If I go to speedtest.net both the upload and the download works flawless.However, after around half an hour it's virtually impossible to upload, which gives heavy lag in programs like skype and games. If you try to speedtest.net now the download is still fine, but the upload gives a result of 0.1mb/sec after trying to even start the test for 3-4 minutes.Router giving up upload completely
I've tried to change the IP in the router to prevent a conflict between it and the switch. The problem is still there whatever IP I choose though, I simply have no upload.I've also tried to disable the DHCP, mess with the MTU and to enable the Access Point mode with no result.
View 2 Replies
ADVERTISEMENT
Jul 21, 2011
I bought the DIR-655 less than a year ago in Amazon, shipping it to NY. And then I came back to Uruguay. Almost 3 months ago the router stopped working completely and I started to search for support in Uruguay.After calling US support I was told I should contact the local or regional D-Link (which I later found is D-Link LA). And via DLinkLA.com I found the company TELEDATA S.A. url... who does the official support for D-Link in Uruguay. They told me the router couldn't be fixed, and told me DLinkLA, which is based in Chile, would either send me a working one (they also told me the service/warrany was already approved), or send me the money and gave me their contact details.After two weeks of contacting them, trying to get their attention, they finally told me it was not their responsibility because it was bought in the US. And now they don't return my e-mails.
View 5 Replies
View Related
Jul 2, 2011
My router is showing two separate SSIDs, dlink and dlink 2 it only recently started doing this and around the same time my router has been constantly rebooting when there's little or heavy internet traffic.I have a DIR 655 Hardware Version: A4.Firmware: 1.21 NA
I refuse to go to any version above 1.21 as 1.21 is the most stable firmware for the 655, I have tried all other with terrible outcomes and wireless performance.I've looked around and most people think it's a joke or something, always saying it's probably a neighbors wireless, but that's impossible since I'm on an acreage and my neighbors are too far away for us to be receiving their wireless signals, and if I change the password and encryption type (WPA/WEP/WPA2) I have to change the security settings on both dlink and dlink 2.
Also I have the normal 192.168.0.1 gateway to access the router under the "LAN" section under Status on the router, but under WAN I have a completely different gateway that just recently showed up. I have no idea where this came from or what happened.
View 4 Replies
View Related
Nov 6, 2012
So network was running fine for about a year or so. Network consists of 1 Motorola SB6120 cable modem attached to a D-Link DIR-601 wireless router. All settings were default except for SSID and WPA password. One day I just couldn't access internet anymore. I've narrowed it down to the default gateway that is being given out through DHCP. The default gateway that is being given out is the IP of the modem (192.168.100.1) and not of the Router (192.168.0.1). I can't find any option on Wireless router to be able to force the gateway address when handing out the gateway IP. Theoretically I thought I should be able to put router on same subnet as modem as 192.168.100.2 but that still doesn't work. If I set the IP adresses statically on the PCs and give it the Gateway of the Router everything works fine. I should mention this is for my boss' house and basically I dont want him calling me everytime he has a friend come over and I have to talk em through setting up a Static IP.
And just for an example this is what I get if I use DHCP:
IP Address: 192.168.0.155
Mask: 255.255.255.0
DNS: 192.168.0.1
Default Gateway: 192.168.100.1
And If I want it to work I have to change the default gateway to 192.168.0.1 I've tried updating routers firmware and reset to factory default numerous times. Is it possible for a router DHCP stop working?
View 3 Replies
View Related
Jun 30, 2011
I just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
View 12 Replies
View Related
May 14, 2011
Is there any way to disable internet access for selected PCs, while still allowing them to access the LAN?
View 2 Replies
View Related
Sep 1, 2012
I have a DIR-615 router. I would like to know if it is possible to block a PS3 from accessing the internet completely, without blocking any other computers/devices. I have access to the router, but not to the PS3 itself.
View 3 Replies
View Related
Jan 15, 2009
We have a new DCS-5220 that we're playing with, seeing what we can do with it, and have a number of questions as well as one possible bug to report. I was somewhat surprised when tier 3 support said this was the best place to cover them all - including the bug.We are using firmware version 1.02, which is what the camera came with.
In the webgui, under Configuration > Tools > System > "Turn off the LED indicator" this is completely ignored by the camera. The red power LED is always on, and the green status LED flashes as long as it has a network connection. This is clearly a bug.What is the root password?Is there a URL we can pole for a static image? (ie.url... which would trigger a snapshot every time the URL is requested)Are there any shell commands for motor control? If so, what are they?Is there a shell command to retrieve logged in users? If so, what is it?Is there a shell command for controlling the LED activity? It would be really nice if the status LED lit green when there was someone logged on to the webgui. Perhaps this is the intended activity, and it not doing so should be filed away as part of the above bug..
View 14 Replies
View Related
Apr 7, 2012
Buying a TP-Link W8961ND modem/router. Didn't work at all, except for a vague sense I got that the internet wasn't spending as long 'down' as previously when it did drop.And now today my housemate and I are both connected and suffering these intermittent drops, which become more and more frequent, until finally the internet cuts out and won't return. Now I cannot get the TP-Link router to connect to the internet at all. However, switching back over to the original D-Link router now the internet DOES work, but still only intermittently. As I've been writing this it's dropped out for a couple of moments twice!
View 10 Replies
View Related
Mar 31, 2013
I have two servers running behind my D-Link DIR-655 NAT router. Obviously, I cannot allow outside access to both of them simultaneously without putting them on different external ports, which I don't want to do. (DNS can only redirect to the common external IP of my router, not the unique internal IPs of my servers.) The easiest solution I can think of to this is simply to put one of the servers completely outside of the router so that it grabs its own IP address from Comcast (and thus allows me to change my DNS records so that the destination IPs are different.) Is this possible, and if it is, how do I do it?
P.S. I've already tried putting one server into the DMZ (Demilitarized Zone) on my router to no avail.
View 1 Replies
View Related
Nov 10, 2011
I have this D-Link DIR-825 and it was working fine till yesterday. All of a sudden it stopped connecting to internet. I restarted it and tried to login to the router but failed. I called the support and did a hard reset of the router. After that when I am not able to connect to the router from my computer for configuring it again. When I connected the Router to my computer via LAN cable sometimes the LAN port is glowing and sometimes it is not. I tried different LAN Cables too. But nothing is working and I am not able to get to the router page.
View 5 Replies
View Related
Jun 10, 2011
ISP is Comcast. The routers hardware version is A4 with firmware v.1.33NA. The upload speed used to be above 4Mbps but recently it has gone down to below 1Mbps. It comes back to above 4Mbps if the router is bypassed or the PC is directly connected to the modem.If I on/off power cycle the router, the speed comes back but only for short period. I tried a new DIR655 of hardware v.B1 with firmware v.2.00 but exact same problem was noticed. I tried my old spare router of Linksys WRT54G and no such problem was noticed.
View 10 Replies
View Related
Oct 4, 2012
I have a DIR-615. My cable connection is 10M and my upload velocity it's about 800K.
If I plug my cable modem right through to the computer, the upload velocity it's 800k indeed.
But when I access the internet through the router plugged on the cable modem, the velocity drops down to 400K.
That is a big problem for play games like fifa. I have a huge delay on the commands and I think that it's caused for the low upload velocity.
View 3 Replies
View Related
Dec 23, 2011
Been plauged with some slow speeds lately and decided to check the speeds, with cable in modem i have 4.9 mbps upload but when i go through the router i have 0.3 mbps. Router is relatively new, just a couple months, firmware 8.00.
View 5 Replies
View Related
Jan 6, 2013
When I bypassed the router and connect my pc to the cable modem directly, my download and upload speeds are over 20mbps/10mbps. But when I connect my cable modem with the router, it reduced dramatically to under 10mbps/5mbps.So the bottleneck is with the router. How can I troubleshoot the router to remove this bottleneck?
View 14 Replies
View Related
Aug 17, 2012
We recently bought a home and just moved in. That being the case, we got a new ISP (Cincinnati Bell DSL). The service is advertised as "Up to 5Mbps."
My current equipment:
PC:
OS Name Microsoft Windows 7 Home Premium
Version 6.1.7600 Build 7600
Other OS Description Not Available
[Code].....
So what can I do to achieve faster speeds? Am I limited by the hardware I have? My Dell is roughly 6 years old. Am I limited by Cincinnati Bell? Is it the location of the wireless router? Are there settings I can adjust to create a faster connection?
View 6 Replies
View Related
Nov 25, 2012
I have recently acquired a network connection of 100Mbps download and upload, and a dir 615 with dd-wrt.
I made all the connections and configurations , and everything seems to work fine it says it's connected at 300 mbps wifi, except it is not . I tested the internet speed and got this :
80 mbps Upload
35 mbps Download
I know that connecting via wifi will loose bandwith, the problem ins't that, I just cant seem to find the cause for the download rate to be less than upload and not equal... , when connected to the cable I get a stable 100/100.
View 1 Replies
View Related
Dec 25, 2011
first one had to get rid of because just wouldn't work with a 3CX server, anyway, I have a DIR-655 A4 factory shipped with 1.32NA I am trying to update the firmware to 1.34NA but it will not let me. It keeps saying Code:
View 6 Replies
View Related
Apr 5, 2012
I have tried Intel tools and latest drivers ( w/ and w/o pro wireless utility) but cannot pass thru code 10 error. Tried uninstall and install....as earlier card 4965 agn worked fine but seems like some conflict is stopping successful 5300 agn driver install.
View 20 Replies
View Related
Dec 3, 2012
Region : Romania
Model : TL-WR841N
Hardware Version : Not Clear
Firmware Version : Latest
ISP :
i just bought this router, all good until i had to upload wireless over ftp or samba. It is version 8.2
Firmware Version:
3.13.27 Build 120802 Rel.51024n
Hardware Version:
WR841N v8 00000000
I bought this router for the advertised 300 mbs, my last 150 router was giving me 6/7 mbs over wireless upload on ftp. Tp link router is giving me 800 k.
Download works on wi fi , i got 9,3 mbs from a 150 N adapter.
I tried all security options , even mac filtering . And i am trying to ftp over network , not the internet.
View 6 Replies
View Related
Nov 24, 2011
where to change version of windows I can not find where to change the version of my windows to make it compatible with my router..I know that there is a place to change it,but I can not find it...I have Windows XP and it is compatible with my wireless router.
View 3 Replies
View Related
Nov 8, 2012
Region : Romania
Model : TL-WDR4300
Hardware Version : V1
my Wi-fi card is an Intel Centrino 130N. When I connect to the Internet directly, the speeds I get are: DL: 11 MBs and UL: 9 MBs. (I know the difference between MB and Mbits). Although, when I'm connected through wireless, I get: DL: 3.4 MBs and UL: 4.7 MBs.how do I get my DL speed to be higher than the UL speed in wireless mode ? I read somewhere I have to disable QoS and WMM, but I simply can't find that option in the router's settings. even if I am in the same room as my router, when I check the status of the wireless connection, the maximum speed is 72 mbps. Should that be 130 mbps, as I run it in N mode, not G? How to improve that ? I have Win 7 and all the latest drivers and everything.
View 3 Replies
View Related
Jul 4, 2011
I've had this WRT300N for several years and it has worked very well.It suddenly dropped all wireless connections and no one can re-connect. My main pc is hard wired directly to the router and works perfectly as always. 3 wireless pc's and 3 handheld devices suddenly can't connect. I've powered down my modem and router for several minutes, but nothing changed. The firmware was upgraded a long time ago and there are no other upgrades available.
View 7 Replies
View Related
Sep 14, 2011
I purchased an E4200 from a retail store about ten days ago.It completely quits periodically. Even the managment interface is gone. It seems to just die. The only fix is to unplug it, count to ten and plug it back in.router also gets extremely hot. I have tried locating it in several places, no matter where I put it, it still gets very hot. Right now I have it straddling a trash can so that it has about two feet of air space under it. It is still uncomfortable to the touch.
When I contacted technical support all they would do is walk me through setting it up from scratch again. I've done that many times, and I do not want to do it agian. Setting the router up agian will not make it cool down.
1. Exchange this for another one, probably from the same batch, at the store?
2. Fight with Linksys tech support to get a waranty return? (Any input on how to get them to do this?)
3. Return this router altogether (paying the retailer's 15% restocking fee) and look for another brand?
View 8 Replies
View Related
Jun 26, 2012
My WAG120N router has stopped working completely. None of the Ethernet ports or the wi-fi signal button is lit,power light continues to blink for 10 odd mins and then comes to a rest. Tried to login to admin portal without any success, tried to reset it pressing the reset button in the back without any success.Tried the 30-30-30 reset method without success too.
View 3 Replies
View Related
Jun 4, 2011
I have a RVS4000 and a WRT54GL router at home... I am planning to power down my home completely for several hours, my question is will I have to re-setup everything or will it retain the settings within the router?
View 6 Replies
View Related
Mar 14, 2011
Linksys WRT54G v5 Router
Arris TM502G/CT Modem
Whether it be downloading or just trying to watch a video on youtube. For some reason everytime I try to download something it appears to start fast but then it basically just stops. I'm running windows Vista and I've tried going into the router security settings and unchecking Block Anonymous Internet Requests.
View 1 Replies
View Related
Mar 3, 2011
I've just been on the phone with tech support and it appears that the latest firmware that Cisco Connect is stating that one should install is faulty and is bricking routers.
I've tried resetting it, holding the reset button while powering up for over 5 minutes with no change.
All the router does now is the power light is blinking but no access to the router is possible at all.
View 2 Replies
View Related
Oct 21, 2011
I have a 3750 acting as my WAN router connected to our MPLS provider via ethernet. For a couple days my inbound bandwidth has been completely saturated at 20Mbs (the speed of my link). I know this model of switch does not support netflow, but is there any other way to try and find out what is using all the bandwidth? I have pretty much ruled out anything on the internet since the in/out interfaces of my firewall are not seeing much traffic.
View 3 Replies
View Related
Dec 26, 2012
My old WRT54G V8 router has been acting up lately. It keep dropping the connection out of the blue. Sometimes I'd be browsing the Internet when the router's signal vanishes completely, it disappears from the list of available wireless networks on not just my computer, but my smartphone and all other devices in the household! Other times I keep connected to the network but there's no access to the Internet. Everything seems fine on the ISP's part, I can connect just fine directly from my modem, so I'm certain the problem is with the router. Besides, these problems are solved by just power cycling the router.
View 4 Replies
View Related
Apr 24, 2013
I posted my complaint on Amazon.com recently. My E4200 router stopped allowing traffic through ports completely. I was able to unplug the power and allow the router to cool, and the router would work for a while then stop after about 10 minutes. I assume that the unit was overheating, but I do not have the equipment of a test facility.I bought a Belkin AC 1200 router which is a bit of an upgrade from Amazon.com. I do not think that there is anything that Linksys can do for me as my warranty expired. I just thought that when I spent what was to me a lot of money the router should have lasted longer.
View 5 Replies
View Related
Oct 3, 2011
I was in the Wireless tab>Basic Wireless Settings and then I clicked the "Reset Security" button. I don't know what that did but I've been completely shut out of my connection ever since and I don't know how to fix it. I tried doing the install sequence of the router just now (Clone MAC address, then release and renew DHCP, power cycle modem, router, and PC) but it still didn't work.
View 1 Replies
View Related
Oct 1, 2011
How Do I give the Static IP Address given to the router by the ISP to machine
View 1 Replies
View Related
