Been plauged with some slow speeds lately and decided to check the speeds, with cable in modem i have 4.9 mbps upload but when i go through the router i have 0.3 mbps. Router is relatively new, just a couple months, firmware 8.00.
View 5 RepliesI just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
I just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
I live in the tampa bay area, I have bright house (BHN) as my service provider, which provides a Road Runner Lightning (40/5) package. I previously used BHN's top tier (20/2) back in July (and prior) with no problems.
After converting to Lightning in August of this year (2010). Of course, BHN (and every other provider) wants to force a modem/router down your throat, so I had them bridge it (in short, turn it into a dummy modem with no routing). I had an SMC branded modem gateway at the time. I work from home 2 days a week (so I can spend more time with my kids during morning, lunch, right after work) and this requires me to use QoS to ensure my VOIP work calls don't get dropped, if the family is watching youtube videos or watching netflex.
My network was as follows SMC Modem >WAN IP>>WAN Port>>D-link DIR-655>>Switch Ports>PC1, PC2, PC3
Everything seemed fine (from a usability stand point) till about 2 weeks ago when my upload speed seemed to grind to halt. Normally I was able to upload about 200-300K per second, and I noticed this dropped to about 45K per second during a drop box upload. First thing I did was power cycle both my modem and router (in the proper/usual order). After they both come up, I start using speed test to find out what my upload speeds were. I was getting about 39Mbps down, but only .56Mbps up still. I factory reset my router.... test, similar speeds. Power cycle all computers (just in case), and then modem/router. Tested, similar speeds. Updated the firmware to the latest. Same issue
Called BHN customer service, they factor reset it, but it wasn't in bridge mode. If I by passed the 655, in factory mode (non bridge mode) upload speeds returned to better than expected states. If I bridged the cable modem, upload speeds seemed to crash.
Had BHN replace the modem, seemed fixed for a day, then issue came back. Had them come back out and replace it again, this time with a Motorolla Surfboard modem... same issue. Fine during factory reset, however after they bridge the modem, upload speeds were fine. Told BHN I would take it from there.. Connected up the DIR-655, and upload speeds crashed again. (.6Mbps). Called D-Link Support, and the Chinese English speaking rep seemed to not be listening to me and tried to have me adjust my MTU as well as Wireless settings. Long story short... the rep was a level 0 id10t and I hope D-link will consider hiring better employees/contractors. So I was all about to give up and replace it with a DD-WRT capable router (which it takes me a lot to want to swap hardware), when I discovered the wan shaping was on. Which I thought to myself... nah... QoS has never messed up before... why would it be the cause. Turned off wan shapping... and voila. Issue seemed to be insta-resolved.
Unsatisfied with that... I decided to dig a lil deeper. I turned on Wan shaping again, but decided to set the settings manually instead of auto detect.
Here are the settings I used... (Advanced Tab>QoS)
Enable Traffic Shaping - Checked
Automatic Uplink Speed - Unchecked
Manual Uplink Speed - 5000
Connection Type: Cable or Other Broadand Network
Enable QoS Engine - Checked Automatic Classification - unchecked (this checked seemed to affect my upload speed by about 5-10% during testing) Dynamic Fragmentation - unchecked (this checked seemed to be the worse enemy for upload speed)
While I know I'm not any network guru (still have to use a subnet calculator for subnetting), I think I did a pretty good job drilling down the issue (once I got passed my service provider replacing modems).
Anyways, I've had overall good luck with D-Link products, even have a 5 port 10/100 switch (all metal) from 1998 that works great. Hopefully, D-Link will just either put more documentation on the web, or hire better employees.
Region : Romania
Model : TL-WR841N
Hardware Version : Not Clear
Firmware Version : Latest
ISP :
i just bought this router, all good until i had to upload wireless over ftp or samba. It is version 8.2
Firmware Version:
3.13.27 Build 120802 Rel.51024n
Hardware Version:
WR841N v8 00000000
I bought this router for the advertised 300 mbs, my last 150 router was giving me 6/7 mbs over wireless upload on ftp. Tp link router is giving me 800 k.
Download works on wi fi , i got 9,3 mbs from a 150 N adapter.
I tried all security options , even mac filtering . And i am trying to ftp over network , not the internet.
I have a PC with an onboard Realtek 8168 PCIe Gigabit connected to a D-Link 655 Gigabit router.Here's the odd situation: when speed/duplex is set to 100Mbps, my upload speed using www.Speedtest.net is fine (~3.0 Mbps). However, when I switched it over to 1.0Gbps, it goes down all the way to 0.06 Mbps. Download speed is generally unaffected. can't tell which is the likely culprit!
Onboard NIC faulty/underpowered?
Faulty cable (highly doubt, I've tried 5+)?
Or is it a matter of settings? I turned off QoS and WISH on the router, but it didn't do much.
Recently my desktop has experienced very slow download speeds (~0.11 Mbps), however the upload speed appears to be in line (~2.0Mbps). These numbers are taken from Comcast's speed test (my ISP). It is obviously a problem with my PC because everything else on the network (PS3, Laptop) have great signals with no problems. I just recently reverted the Desktop back to its factory state, and everything was working fine for a couple of months. The desktop in question uses Vista 32-bit and the Belkin Basic USB Wireless Adapter.
View 1 Replies View RelatedI ru n the speed test from my desktop and laptop and the download speed are in the same range in both pc's, around 20mb/s. However the upload speed is higher in the laptop (around 4 mb/s) compared the desktop (300 kb/s)My connection is supposed to run at 50 mb/s and 5mb/s?
View 9 Replies View RelatedI was wondering why my upload speed btw the test. and reading this forum post: Sudden slow upload speed?
View 1 Replies View RelatedI've been experiencing some problems with my RangeMax wireless NETGEAR router (model WPN824) in terms of wireless connectivity. When directly plugged into my router (i.e. using ethernet cables), the download and upload speed (in mbps - megabytes per second) appear to be working correctly, where we register average download speeds of 15-19 mbps, and 1.99 to 2.07 mbps for upload speeds, as shown on speedtest.net. However, our wireless devices (i.e. laptops and Nintendo Wii) are not picking up the same download speeds, but the upload speed is fine. The problem is that the download speeds of the wireless devices are comparatively low, where speeds of 2.5 to 5.5 mbps are a commonality.
We've tried resetting the router (pushing that small button at the back of the router, using a pin) and have a new 10-character key password. We've also tried simply unlugging the power cable to the router, with disconnecting lengths of about 10 seconds to over a minute for separate attempts. It is also worth noting that the router occasionally disconnects and re-connects on irregular intervals, and we have many wireless devices attached to the router (though many of these are not in use and are very often disconnected from the internet, so I do not think the router is being overwhelmed).
I am currently paying for 30 mbps downloading speed and 2 mbps with respect to uploading, though the 30 mbps downloading speed will likely only be registered if directly connected to the black box (modem). As such, values of 10 to 18 mbps for downloading speed for a wireless device would be considered "normal". Why would our wireless devices not pick the correct mbps download speed? Is it possible that there is a setting on the NETGEAR SMARTWIZARD page (192.168.1.1) that is preventing this?
This is the first PC I have ever built, but I built it with a buddy who is very experienced and everything went okay. The computer is maybe 3-4 weeks old now, everything is running fine, until today when I decided I wanted to try streaming some Diablo 3.This is when I discovered my upload speed was absolute garbage.I have verizon FIOS - I pay for 15/5, the download speed is always at 20+ mbps, I have never had any problems with it., but my upload speed is fluctuating between .34-1.5 mbps, changing every second.I know this is a problem with the computer because I brought in my old laptop, unplugged the ethernet from my new desktop, plugged it into the laptop in order to keep all variables the same, and it was getting 25/5 without any hesitation.When I was downloading the drivers for my mobo I installed something called Windows Firewall with Advanced Security(maybe that was with a windows update, im not sure).
Specs of my PC (if this matters)
-Asus P8Z77-V LK
-8g ddr3 Ripjaws
-i7 2700k
-Corsair H60
-EVGA GTX 670
-Crucial 128g M4 SSD
-Caviar Blue 1TB HDD
-750W OCZ Modular PSU
After every attempt and changing of radios still download and upload was very slow.
View 1 Replies View RelatedI'm having a big trouble with my internet connection. The Upload speed is extremely slow after i got a new mainboard, that problem appears.[code] I'm tired with my suck internet connection! Upload a 1MB photo to Facebook took me hours..This problem has started for a week.
View 1 Replies View RelatedI have the WRT160N. Using [URL], I can get 2.5Mps from wired ports, but less than 0.5 Mps using the wireless.
View 9 Replies View RelatedI recently installed an E4200 router/AP and, on one desktop, an AE2500 USB Adapter. All the other devices on the LAN work fine and the laptops, even show improved tranfer rates. The desktop, with the AE2500, shows good or very good signal strength, but the speed is down around 5.5 Mbps. Running a full backup of the HDD proves the slow speed.
View 7 Replies View RelatedI got a new Netgear N600 Router and installed. Everything works fine, except my PC, which is using a Belkin F5D8055 V2 USB adapter. My upload speeds are less than 1Mbps, while on my net book, ipad, and iphone they are 5Mbps+. I can not firgue out how to fix this. I am running Windows 7 Home Premium, SP1. My PC has an I7-920, 18GB RAM, and 2x Radeon 5870.
View 1 Replies View RelatedI am using a Cisco RVS 4000 to test a new 10M/10M internet connection. I'm having a small problem performing the ISP's speed test (speedtest.cavtel.net). The download test consistently gives me 10Mbit/s, full speed for the connection, however the upload speed is usually about 5.5 Mbit/s. My ISP has been onsite and has checked the lines and tested directly, and we have determined that if connected directly we can test to full upload speeds, but when the RVS is connected, we cannot get full speed.
We've tried different cables, reseting to factory defaults, updating firmware, changing port settings, and toggling most of the other setting on the router. Some settings do have a minor effect on the upload speed, but nothing that gets me back up to 10Mbit/s.
I did notice that there appears to be no way to set speed and negotiation settings on the WAN port. Perhaps I am missing it, because that seems like a possible culprit.
Otherwise, the only only thing I can think of is a warranty return to determine if the unit itself is defective.
I bought an E2000 router as a replacement for my WRT54G router, since my internet speeds had been upgraded. But this E2000 router has been giving me nothing but trouble.
Wired through both the router or modem, I get my topspeed of 110mbps. However, as soon as I switch over to the wireless N function, my speed drops to only 25mbps. As far as I know, wireless N should have a much faster speed than that. Even my old WRT54G had faster speeds than this new router has. Mind you, that the distance between my laptop and router is about 3 inches away. The further I go away from my router, the speed exponentialy drops (20 feet, and the speed even drops to below 10mbps). Even with different laptops that have completely different wireless cards. Now honestly, I have tried EVERYTHING to get the speed up. Both 2.4 and 5ghz, 20mhz only, 40 mhz only, different channels (currently the router is in channel 11, being the only router in that channel), setting the network to G-only. I tried changing the Beacon interval thing in numerous settings, I even tried changing the MUT. Firmware is completely up to date. I have also tried placing the router on a completely different place, to make sure there was absolutely no interference (tough that shouldn't be an issue if my laptop is only 3 inches away) I tried changing the security mode to something different than WPA2/AES.
Nothing worked, if anything, it made it worse in some cases. I have litteraly tried every option I could find online, except for trying a third party firmware like DDWRT, which worked excellently for my old WRT54G, though I read that speeds can't be improved on this E2000 with a third party firmware.
Is there anything else I can do, or should I assume that my router is defective?
When I'm in my bedroom, I get a very poor connection and my speed drops to about 0.25mbps. Abysmal, so I bought a WiFi range extender to get me a better signal. It works, and it allows me to get a speed of about 5-6 mbps, without dropped connections. Still slow, but at least it works. The weird thing is, wired through my router or modem, I get about 9mbps upload speed. With this extender, I get the same 9mbps upload speed in my bedroom, though only 5-6 mbps download speed. You'd think that the upload speed would drop simultaneously with the download speed. How can my upload speed be higher (maxing out) than my download speed? I wonder if my transmitting antenna of my router isn't defective.
I have working internet behind cisco 2811 on all vlans however upload speed is very slow and ftp server download is slow and times out, previously when directly connected to modem/router was fine? This is router config below:
Current configuration : 2229 bytes
!
! Last configuration change at 02:21:18 UTC Tue Mar 12 2013
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
[code]....
I Have BT Infinity and they are pushing 70mbps to my house ....i bought an EA6500 and i had real bad internet speed but amazing conection speed with my BT Home HUB3 ... 23Mbps with Cisco EA6500 and 68Mbps with my BT Home Hub3. I found out it was the Media Prioritization so just to be safe i reset my factory settings and made sure it was turned off. Just like magic i get the same now as the BT Home HUB3 .
View 1 Replies View Relatedi have WRT610N v1.0 with latest original firmware but ftp upload speed and torrent download speed is terribly slow.
View 3 Replies View RelatedSo I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View Relatedmy problem is that i have a computer connected via gigabit lan with a cat5e cable.i have a notebook with a d-link dwa-140 usb wifi adapter connected.and the max transfer speed i get is 14 mbps. d-link dir-655 firmware 1.34eu.in windows it reports 300mbps.in the router it reports 270 mbps sometimes 300. the settings in the router is 40mhz only,. ch 13. wpa2 aes. as described in the sticky.the devices are within 3 ft of each other.
View 2 Replies View RelatedI have 2811 Cisco ISR and two ISP links - one is 8 Mbps and the second is 4 Mbps. The question is - is it possible to aggregate link speed up to 12 Mbps?
View 4 Replies View RelatedISP is Comcast. The routers hardware version is A4 with firmware v.1.33NA. The upload speed used to be above 4Mbps but recently it has gone down to below 1Mbps. It comes back to above 4Mbps if the router is bypassed or the PC is directly connected to the modem.If I on/off power cycle the router, the speed comes back but only for short period. I tried a new DIR655 of hardware v.B1 with firmware v.2.00 but exact same problem was noticed. I tried my old spare router of Linksys WRT54G and no such problem was noticed.
View 10 Replies View RelatedI have a desktop and laptop here, the desktop being mine custom built wireless and all, and my buddies desktop.The issue that I'm having is that my desktop, regardless of wired or wireless gets 25 mbps down speed, and the laptop gets only 2.5 mbps down speed wired or wireless
View 4 Replies View RelatedWhen I bypassed the router and connect my pc to the cable modem directly, my download and upload speeds are over 20mbps/10mbps. But when I connect my cable modem with the router, it reduced dramatically to under 10mbps/5mbps.So the bottleneck is with the router. How can I troubleshoot the router to remove this bottleneck?
View 14 Replies View RelatedWe recently bought a home and just moved in. That being the case, we got a new ISP (Cincinnati Bell DSL). The service is advertised as "Up to 5Mbps."
My current equipment:
PC:
OS Name Microsoft Windows 7 Home Premium
Version 6.1.7600 Build 7600
Other OS Description Not Available
[Code].....
So what can I do to achieve faster speeds? Am I limited by the hardware I have? My Dell is roughly 6 years old. Am I limited by Cincinnati Bell? Is it the location of the wireless router? Are there settings I can adjust to create a faster connection?
Region : Romania
Model : TL-WDR4300
Hardware Version : V1
my Wi-fi card is an Intel Centrino 130N. When I connect to the Internet directly, the speeds I get are: DL: 11 MBs and UL: 9 MBs. (I know the difference between MB and Mbits). Although, when I'm connected through wireless, I get: DL: 3.4 MBs and UL: 4.7 MBs.how do I get my DL speed to be higher than the UL speed in wireless mode ? I read somewhere I have to disable QoS and WMM, but I simply can't find that option in the router's settings. even if I am in the same room as my router, when I check the status of the wireless connection, the maximum speed is 72 mbps. Should that be 130 mbps, as I run it in N mode, not G? How to improve that ? I have Win 7 and all the latest drivers and everything.
Installation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
300 M bps drops to 150 M bps when it recycle power. I met all requirements for 300 M bps connection this happen only in 2.4 g Hz Band width.
View 1 Replies View RelatedI just bought this router. Unfortunately I'm losing close to 3mpbs !
When I was connected directly to the modem i had a little over 12.5 Mbps
Now I'm stuck at 9.5mbps and it won't go higher!
I read a bit over the forum. I tried turning off the QOS but it didn't change a thing.
Here a little extra information;
My internet provider is Cogeco
MY computer is wired
I tried 2 internet tester, both give me the exact same result
My DIR655 is A4 with firmware v.135.
My normal uplink speed is above 4 Mbps but the speed goes down to 0.4 to 0.8 Mbps. The above unit was received from D-Link as a replacement for the same reason, but it worked for at lease 12 hours.
If the power is OFF/ON cycled, the normal speed comes back but last only about 10 minutes.