I have configured Squid on my system having Windows 7. I didn't missed any steps. In Services it is showing Squid running.But my internet is running directly without any proxy settings. And when i change to proxy settings at port 3128, internet stops working. I had installed earlier and it was working fine. but now I am also using ICS to share internet connection from a broadband to a lan through my system.
View 7 RepliesI'm testing WCCP in a lab environment (Another checkbox on my way to CCIE).The setup- a WS-C3560-8PC switch running IOS 15.0(1), IP Services with crypto.- Two client computers connected by wire to the switch, running Windows 7.- A virtual machine in bridged mode running on one of the machines, running OpenBSD 5.0 with Squid 2.7 installed and running.- Everything in the same subnet: 192.168.163.0/24, the OpenBSD is at .5, the switch at .3 and functions as the default-gateway for the computers with no ICMP redirects (the real gateway is at .1 but the switch forwards everything).Squid seems to work, albeit inefficient, but that's not the issue.illing in the IP of the OpenBSD in the browser as proxy with the proper port works.Since the 3560 does only support WCCP over layer 2 adjacencies and masks, not hash buckets, I've configured these options on both the Squid and the 3560.
View 19 Replies View RelatedI am using a cisco 3750 in my network as a gateway, and above it I use a squid machine for caching my internet. My network is like this:
Basically I have two VLANs on my network which are VLAN10 and VLAN100, VLAN10 is the cooperate network of my office. VLAN100 is the management VLAN which i use for the switches. I keep the squid as well the client in VLAN10.
squid (192.168.1.50)---->cisco 3750(192.168.1.123)---->Distribution Switch(cisco 2960)---->client PC (192.168.1.5)
I have done nating on squid and internet is working pretty fine when I use the client gateway as the squid, but when I use the cisco 3750 as my gateway after adding route maps for forwarding the internet traffic coming to the cisco 3750 to squid it disconnects me from internet as well I cannot even reach the switches from the corporate network. These are the only Lines I used for the routing:
!
route-map proxy-redirect permit 10
match ip address 110
[Code]......
So all of a sudden the trusty HP 4000 stopped printing. A little bit of troubleshooting and I found out that the problem was the JetDirect card. I purchased a new one (615n - same model as the old one), installed it, ran a printer configuration page, confirming I have an IP (192.168.x.x) and subnet mask (255.255.255.0), config by DHCP.Also, ran a ping test and it appears to be fine?
View 1 Replies View RelatedI have a switch that I have configured for jumbo packets, but they don't seem to be functioning. I have set system mtu jumbo 9000. The hosts are connected via 2x EtherChannel links. The hosts are jumbo frame enabled, and can ping their own local address using jumbo packets & do-not-fragment flags on the pings. They cannot, however, ping each other or the switch that way - it always says that the packet requires fragmentation. I know the attached machines (they're all VMs) and virtual switches support jumbos because I can ping within the virtual interfaces of the VMs. It's just traffic that goes over the switch that fragments.The switch is a WS-2960G-48TC. Here are the various outputs, with a section of config at the end.
hrnacancwtdevs3#show system mtu
System MTU size is 1500 bytes
System Jumbo MTU size is 9000 bytes
System Alternate MTU size is 1500 bytes
Routing MTU size is 1500 bytes
[code]....
I have a NM-1CE1U working on my router 2600 , configured with frame-relay . But seems it does not work on my router 2811. I have check that the replacement is HWIC-1CE1T1-PRI , right ？
But the problem is these two modules have different interface type , I want to keep my cable interface type and find one module card working on 2800 or 2900 router , can configure frame-relay.
I have configured Cisco 1841 router PAT buts its not worked, find the below configuration details,
In LAN interface
Interface gigabit Ethernet 0/0
no shutdown
[code]......
Similarly I have configured static and dynamic nat but its not works in my customer place.
I am using ACS 5.3. I have succesfully configured Machine Authentication for a Windows 7 laptop using EAP-TLS. The ACS is configured with an Active Directory external identity store where the Windows 7 laptop is configured as part of the domain. I'm pretty sure that the ACS was using the AD to authenticate the laptop's name because at first the authentications were failing because I had the Certificate Authentication Profile configured to look at an attribute in the client certificate that was empty. When I fixed that, the authentication suceeded.
I started doing some failure testing so I disconnected the Domain Controller from the network. Sure enough, the ACS shows the Active Directory external store is in the Disconnected State.I then went to my Windows 7 laptop and disconnected the wireless connection and connected it again, expecting it to fail because the AD is down. But it succeeded! My Win 7 laptop is accessing the network wirelessly through a Lightweight AP and 5508 WLC. The WLAN Session Timeout was set for 30 minutes. So even with the AD disconnected, every 30 minutes, the ACS log showed a successful EAP-TLS authentication. I then changed the WLAN Session Timeout to 2 hours 10 minutes. Same thing, every 2 hours 10 minutes, a succesfull EAP-TLS authentication. I really don't know how the authentications are succeeding when the AD is not even connected. Is there a cache in the ACS?
I am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
View 3 Replies View RelatedSo Im trying to learn a little bit more about WCCP so I thought I'd load up a centos VM and just install squid on it. With the base config running I can setup an explicit proxy by configuring my IE session to use the squid IP on port 3128. Proxy works fine and I see entries in the access log on the centos box. Now, since Im only running squid on the box Im going to change the listening port to 80 so I can transparent proxy with WCCP on my ASA. So I set the WCCP2 config on squid as shown.
View 10 Replies View RelatedI have been tasked to setup a Transparent Squid proxy and do redirection on a Cisco 6513 Switch.I don't have access to the SQUID but think that my config below should be OK. We have setup a TEST user Vlan 13 . Any traffic from this destined for the we on 80 or 443 should be redirected. Vlan 10 is where the Squid proxy is sitting. [code]
View 3 Replies View RelatedI have ASA 5505 firewall with base license.I am using 10.91.40.0/24 IP series.Below are the requirements that i need to configure
1. First 30 IP's need to have direct internet access.
2. All remaining IP traffic i need to send proxy server( Squid server).
Note that my ASA 5505 is in base license and also tell whether my ASA is support for this feature.
Right now, in my network there is no proxy server and all users go straight through the ASA to access internet. I would like to put a squid with dansguardian (for web filtering). Steps in getting all http and https traffic from ASA go via my squid?
View 18 Replies View Relatedi have configured some machines into a workgroup. all machines are opening except two machines having windows 7 . they are showing a window for username and password as appears in a domain. how to correct it
View 3 Replies View RelatedMy computer is only one month old. I did a clean install of Windows 7 on it and a clean install of Ubuntu 11.04 (dual boot). With Ubuntu, the wireless works without issue. In Windows, the connection is fine through a cable, but wireless networks are not detected at all. Since I did a clean install, I had to install drivers manually. I got these from the Samsung website (my laptop is a Samsung Q430). I think that my Wireless card is Broadcom but I am not sure. The wireless did work at the start, but there were connectivity issues, and so I removed the wireless driver from the device manager and reinstalled the Broadcom drivers. Now I can't get any wireless at all in Windows.
I think I may be missing some drivers, but I'm not sure. I have the Broadcom Wireless Utility but I can't get it to do anything useful. Right now I'm connected through a cable. Here is the result of ipconfig[CODE]
in windows 7 64 bit lan is not working
View 1 Replies View RelatedI have windows 7. Search engines worked fine when first used, now all I get are errors, With IE9 and Firefox.
View 1 Replies View RelatedI have tried a lot of drivers and even tried installing Vista 64 bit drivers (something that worked for someone in some thread), but it won't work.The adapter is recognized by the computer, but the smart wizard won't launch.
[code]...
I am having problems with any type of Network Card or Network USB adapter working with my PC running Windows 7. I had a LinkSys WMP54G PCI card working on this computer about a year ago as I was needing to use a wireless connection but then I didn't use it for 6 months. When I went to use it again, it wouldn't pick up connections at all.Thinking it was an issue with the card, I picked up a Edimax 7612UAn USB adapter thinking it should work out of the box. When I plug the USB adapter in, the standard Windows driver installation tries to run but an error message occurs stating "Device driver software was not successfully installed" accompanied by "Realtek RTL8191SU Wireless LAN 802.11n USB Failed". If I try to install the drivers manually, nothing changes and in Device Manager the following error message is displayed under Device Status "This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)".
View 3 Replies View RelatedI am having problems with any type of Network Card or Network USB adapter working with my PC running Windows 7. I had a LinkSys WMP54G PCI card working on this computer about a year ago as I was needing to use a wireless connection but then I didn't use it for 6 months. When I went to use it again, it wouldn't pick up connections at all. Thinking it was an issue with the card, I picked up a Edimax 7612UAn USB adapter thinking it should work out of the box. When I plug the USB adapter in, the standard Windows driver installation tries to run but an error message occurs stating "Device driver software was not successfully installed" accompanied by "Realtek RTL8191SU Wireless LAN 802.11n USB Failed". If I try to install the drivers manually, nothing changes and in Device Manager the following error message is displayed under Device Status "This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)".
View 1 Replies View Relatedi had an extra network under my wireless networks that was just called "network" which was not connected to anything, but since i had this, on the bottom right of my screen where it normally showed the bars for the wireless connection, it had the bars grey with a red X on them, but my connection worked fine still.I am using windows 7 64x bit. I always use a wireless connection on my laptop.
View 6 Replies View RelatedI reinstalled windows XP on my computer using the install disk I got with my computer. However, now I can't get on the internet on that computer to update the drivers, and I can't find anything that'll let me do it without internet.I don't have an independent network card, just what's built into my motherboard. Haven't been able to find the driver for it, only programs that will find it for me, using said internet.
View 1 Replies View RelatedI have 2 computers, One running Vista 32, Desktop.Another, Laptop, Win 7 64bit.Both computers have given Error 651 when using PPPoE wired connections, usually at the peak of the day.My ISP says that Error 651 is the problem, while I am starting to think its the amount of bandwidth their giving my neighborhood/home.Also, can that dosen't work,how to fix the overall problem of my Internet shutting off at peak hours?
View 2 Replies View RelatedI buy the Huawei K3765 USB Modem (unlocked, so I can use all operators).
After I plugged it in, it installed the Mobile Partner Software succesfully. The phone and SMS function is running well. I can call and text someone through the modem.
But the problem is when I tried to connect to the internet it shows error message:
Error 31: A device attached to the system is not functioning
I have tried the modem on another computer (Windows XP and Windows 7 Home Premium 32 bit too) and it worked well. For information my notebook is ASUS K42JR, OS Windows 7 Home Premium 32bit.
I used the wireless adapter (Netgear - WG111v3) on my computer for weeks without any trouble at all. (At the time i installed it, I remember I found out it didn't work/didn't work well on windows 7 so I downloaded some driver or something -- Don't really remember -- and it worked fine.) Suddenly, today, it stopped working. I have tried a lot of drivers and even tried installing Vista 64 bit drivers but it won't work. The adapter is recognized by the computer, but the smart wizard won't launch.
View 6 Replies View Relatedi need to know how to get my wireless internet working on windows 7? what do i do?
View 8 Replies View RelatedMy internet is connected in my laptop. but there is no internet access.. it's shows a yellow exclamation mark...
View 3 Replies View RelatedI just formatted my laptop and installed windows 8 64 bit. The wifi was coming switched off. On checking from settings I was unable to switch it on. I installed the wifi drive from the resource cd but that too didnt work. Then I installed the wifi driver from [URL] Note: removed per privacy policy~RK>. Still the wifi is not switching on.
On removing the existing wifi driver from the laptop, windows somehow reinstalls in automatically.
My service tag is <Admin Note: removed per privacy policy~RK>
My roommate is running dual boot Windows XP PRO (SP3) and Ubuntu 10.10. I am running Windows XP PRO(SP3). Is there any software, that can run on both OS and can create a home network that will work between XP and Ubuntu. He has Samba installed but I have read that that works on Linux not Windows so he can see me but I can't see him.
View 11 Replies View RelatedMy laptop won't connect to the internet at all and status shows limited access to router. It was fine a few days ago until a Windows update. I did a system restore on it back to before the windows update and the internet was working just fine but then there was an automatic windows update again and the connection is gone again. When I try to troubleshoot it says the network adapter is not working properly. I'm currently using the main computer in the house. I can't access any network at all on my laptop and I'm nearly in tears. This has happened before about 7 months ago after a windows update. At that time I did a system restore and reinstalled the updates and it worked just fine. This time nothing. I have tried to check for updated drivers for the network adapters but windows says I'm running the recent ones.
View 8 Replies View RelatedCannot connect to wireless network, I've updated drivers, reset switches and tried any
View 3 Replies View RelatedThe wireless adapter keeps saying unidentified network, I can connect from other computers and they are all working fine.
Edit: Forgot to mention its a ASUS wireless n-15 adapter, also the system is a Windows 7 64 bit. Also, has a ip address 169.x.x.x which i know means no internet connection.
I just finished setting up VPN server on my Windows 2008 server. I defined the users that should be able to access the server and applied permissions. When I test the VPN connection on the LAN (loacally) I have no trouble connecting and establishing VPN connection.However when I tried externally it's a different story. I am not able to connect and always get the same not so clear 800 error ...The remote connection was not made because attempted VPN tunnel failed. I have Zyxel router for my internet connection and I have forwarded all relevant ports I think for the protocols I am using. Port such as 1723,1701,1702,47,50,51,500,1293,443,4500 are forwarded to the server.I am able to telnet to the server on port such as 1723.
View 1 Replies View Related