I have ASA 5505 firewall with base license.I am using 10.91.40.0/24 IP series.Below are the requirements that i need to configure
1. First 30 IP's need to have direct internet access.
2. All remaining IP traffic i need to send proxy server( Squid server).
Note that my ASA 5505 is in base license and also tell whether my ASA is support for this feature.
I have an ASA 5505 that I am using to connect my contractors to via an inside interface, the outside interface is my private LAN. I have setup on our corporate Proxy server to allow traffic from my outside interface of my ASA to go to the internet without credentials BUT log internet activity. The question is I want to know if the ASA can send that http & https traffic to my proxy server and all other traffic to my default route? I want to be able to send all internet traffic to my proxy server. This will avoid me asking the contractors to place proxy credentials in their browsers.
View 6 Replies View RelatedI have ASA 5505 with base license. I like to install proxy server in my network.I configured below commands to forward my traffic to proxy server from my ASA.
If there is any configuration that i need to configure.And if possible send me the configuration guide to setup SQUID server. ( Actually it was set up by the 3rd party vendor)
Right now, in my network there is no proxy server and all users go straight through the ASA to access internet. I would like to put a squid with dansguardian (for web filtering). Steps in getting all http and https traffic from ASA go via my squid?
View 18 Replies View RelatedI have an ASA 5505 with the base license,When I setup the DMZ interface I had to add the deny access to the inside VLAN. The DMZ works fine with WiFi on it, but user's iPhones can't get email unless they turn WiFi off.Is there a simple way to allow HTTPS traffic through the DMZ interface to our internal Exchange server which is NAT'd on the 5505's external IP?
View 3 Replies View RelatedHow do I redirect my port 80 traffic to my Trend Micro IWSVA in my 3550 switch? How do I use PBR? Can I use WCCP in my 3550?
View 3 Replies View RelatedI have setup an ASA 5505 w/ Security Plus with three subnets. The subnets are as follows:
VLANSubnetWAN 10.0.0.80/29LAN192.168.1.0/24DMZ172.30.200.0/24 ]
The ASA is the gateway router at .1 for the LAN and DMZ networks. On the WAN network, the ASA occupies .85 and uses .86 as it's gateway to the Internet. Clients on the LAN are able to access the Internet without any troubles. I have a static NAT setup to map the DMZ server's 172.30.200.81 address to 10.0.0.81. I also have a general NAT that should allow other servers on that network to access the internet, but no machine at all on that network can route outside of 172.30.200.0/24. I used the packet tracer and had it trace traffic coming from the DMZ network to the Internet, and it did not show me any conflicts with any of the access lists or anything else. However, no matter what I do, I cannot initiate traffic from the DMZ and have it go out to the Internet successfully.I attempted to follow the directions in the article PIX/ASA 7.x and above: Mail (SMTP) Server Access on the DMZ Configuration Example; but I have obviously missed something, done something wrong, or perhaps the example assumes something about my configuration that I have not done. See the attached config file that I have scrubbed. I have removed VPN configuration information and other unnecessary parts of the config file to make it easier to read. I have setup an ASA 5505 w/ Security Plus with three subnets. The subnets are as follows: VLANSubnetWAN 10.0.0.80/29LAN192.168.1.0/24DMZ172.30.200.0/24 ]
We have Cisco ASA 5505, 90.x.y.2/29 IP is assigned to outside interface. We have one internal HTTP server so that I use static (inside,outside) tcp interface [URL] to forward all incoming HTTP traffic to internal HTTP server 1. Now we need to add new physical HTTP server 2 so that I would like to forward
HTTP traffic to e.g. 90.x.y.3/29 to 172.16.0.11.
How can I do that? See scenario image (scenario.png) if needed.
We have Cisco ASA 5505 with ASDM 5.2 We have one Proxy server in our Local Lab and pointed to Hosted service(Simple Signal)issue is, When our proxy server send register to hosted server, ASA change private IP and post with outside IP and src port as 1063 every time.
Here is debug log on real time monitoring.
Aug 24 2011 05:21:19 302015 203.xxx.xxx.226 192.168.1.51 Built outbound UDP connection 3774 for outside:203.xxx.xxx.226/5060 (203.xxx.xxx.226/5060) to inside:192.168.1.51/27014 (99.119.161.107/1142)
Aug 24 2011 05:21:19 607001 203.xxx.xxx.226 Pre- allocate SIP Via UDP secondary channel for inside:192.168.1.51/27014 to outside:203.xxx.xxx.226 from REGISTER message
Aug 24 2011 05:21:19 710005 203.xxx.xxx.226 99.xxx.xxx.107 UDP request discarded from 203.xxx.xxx.226/5060 to outside:99.xxx.xxx.107/1063
Here 99.xxx.xxx.107 is Our ASA Outside IP address 203.xxx.xxx.226 is Hosted server IP address. My ASA config is attached.
I am able to ftp from my Head Office to my test machine at the remote location but I can't get the other way around to work. Error message from the Syslog deny tcp src 192.168.50.5/1825 dst 208.124.202.44/21 by access-group "dmz_access_in".I try a couple of ways to fix it but no luck.A partial config of my ASA 5505. [code]
View 4 Replies View RelatedWe have a BT Infinity broadband circuit which terminates at a vdsl modem, I've plugged an ASA 5505 into the back of this modem and gone through the ADSM quick setup wizard (yes I'm that much of a beginner!) The config that's been generated is pasted below, the symptomns I'm seeing are;
The ASA is setup with PPPOE on the internet connection, I assume this is correct as if I do a show IP on the ASA I'm getting an IP address that has been assigned, if I change the password to the wrong one then I get no IP (as expected).
If I ping from the ASA to an internet connection I'm getting "no route" error messages, if I try a "ping outside x.x.x.x" then I get no repsonses.
The ASA can ping it's external IP, the client machines can ping it's internal, however nothing appears to be able to get out.
ASA Version 8.4(1)
!
hostname xxxxxx
enable password xxxxxx encrypted
[Code].....
We have 110mbps internet service. When we have the 5505 behind the cable modem, our speed drops to 55mbps or so. If we remove the 5505, we see the full 100mbps. I assume the 5505 can handle the speed; if so, what other things should I be looking at?As an aside, we used to have 50mbps wich worked fine, then the ISP upgraded to 60mbps and the through put dropped to 30mbps (It always seems to be half)
View 2 Replies View RelatedMy understanding is for insight to outside we need global and NAT, and for outside to inside we need static and ACL? Traffic goes to high to low, I'm just start working with 5505 recently.
View 2 Replies View RelatedI have VPN up and running between two sites. Both sites have Cisco ASA 5505. I can ping across the devices from both networks. But I cannot remote into the servers on the other network.
View 8 Replies View RelatedI have a Cisco ASA 5505 that I have configured. The outside interface is vlan 2 and the inside interface is vlan 1. Port 0 of the ASA is configured to be in vlan 2 and is connected to the ISP provided subnet. Port 1 is connected to my private LAN subnet. I have an additional router connected to Port 2 for guest connectivity. Port 2 is configured to be a member of VLAN 2 so that it can access the ISP provided subnet. From the device connected to port 2 I can ping the vlan 2 interface address of the ASA and from the ASA I can ping the Default gateway of the ISP provided subnet. For some reason the router on port 2 cannot ping the default gateway of the ISP provided subnet. If the vlan were working the same as a vlan in a switch, I would expect to be able to do this. why it is not working or what I can do to get it working?
View 4 Replies View RelatedI'm trying to allow SSH traffic from the Internet to my DMZ. I gave my remote guy my ip and he can see the ASA 5505 but not get into the DMZ. The outside is 70.165.19.137. The DMZ server is 192.168.60.2. I have the inside talking to the DMZ fine. [code]
View 9 Replies View RelatedMy setup is as below
inside host--> ASA1--Outside interface- layer_ 2_Switch1--outside interface--> ASA2--inside interface-DHCP SERVER.
We want that inside host should get ip from subnet 192.168.10.0 /24. This ip pool is configured in DHCP server (ip 172.16.10.1) which is connected to ASA2. There is no routing issue as we are able to ping DHCP srever 172.16.10.1 from ASA1. to do config needed on ASA1 and ASA2 , so that host connected to ASA1 inside interface can get ip from DHCP srever. We have configured 192.168.10.1 /24 to ASA1 inside interface which will be gateway to inside host of ASA1.
I am fairly new to configuring ASA's. I have an ASA 5505 with one outside interface and three inside interfaces (inside1, inside2, and management). I need inside1 and inside2 to be able to talk to eachother but cannot work out how to make this happen. They are both configured to the same security level and the 'Enable traffic between interfaces with same security level' box is ticked. I have also tried adding appropriate NAT and Access rules. The packet tracer suggests the rules are correct for allowing traffic flow between interfaces but obviosly this may not be the case.
View 14 Replies View RelatedWe have 10MB dedicated Internet BW and want to run VC device and due to heavy traffic and BW high utilization at peak hours, VC performance is not sufficient. We would like to reserve 2MB for VC device. How much possible to fix up this configuration in ASA5505 version disk0:/asa724-k8.bin [URL]
View 5 Replies View RelatedI have a Cisco 5505 with a 12Mbps feed. I want to reserve 2Mbps for RTP traffic. I followed the QoS guide here: url... The goal would be that any traffic destined for port 5000 through 5100 UDP or TCP from any IP to any IP on any interface.should always have 2Mbps available to it.
View 5 Replies View RelatedIs there any difference with traffic shaping capability on the 5510 as opposed to the 5505? is there anything the 5510 can do that the 5505 cant? with regards to TShaping?
View 4 Replies View RelatedI am trying to switch out a cisco pix 501 firewall with a cisco ASA 5505 firewall. I am not very familiar with all of the commands for the firewalls and have always relied on a standard command line script that I use when building a new one. Unfortunately, my script is not working with the 5505. What I am doing wrong with the following script? I've masked public IP info with xxx.xxx.xxx and I run it right after restoring the firewall to the factory defaults. I am able to get out to the internet if I browse directly from one of the servers, but cannot access a web page when trying to browse to it from an outside network. [code]
View 7 Replies View RelatedI've setup my Cisco ASA 5505 in transparent mode. I have a Cisco 1841 connecting to the ISP (DHCP client) and F0/0 for inside. The 1841 is the DHCP server. I have my ASA 5505 behind the 1841 in transparent mode (Vlan 1 for Outside and Vlan 1 for inside). The router config is good as when you connect a computer straight to the inside interface I get DHCP and can go to internet, no problems what so ever. But When you're trying to go through ASA isn't not working. if I add a ip any any statement to the access list it will work but having an "ip any any" in a access list is like having no firewall at all.
ciscoasa(config)# sh run
: Saved
:
ASA Version 8.2(4)
!
firewall transparent
hostname ciscoasa
enable password zmQ6OnxvsOOEDNAy encrypted
[code]....
I've got an ASA 5505 with the Security Plus license that I'm trying to configure.
So far I have setup NATing on two VLANs, one called 16jda (VLAN 16 - 10.16.2.0/24) and one called 16jdc (VLAN 11 - 10.105.11.0/24).
From each subnet I am able to connect to the internet, but I need these subnets to also be able to talk to each other.
I have each VLAN interface at security level 100 and enabled "same-security-traffic permit inter-interface", and I have setup static NAT mappings between the two subnets, but they still can't communicate.
When I try to ping there is no reply and the only log message is: 6 Aug 21 2012 09:00:54 302020 10.16.2.10 23336 10.105.11.6 0 Built inbound ICMP connection for faddr 10.16.2.10/23336 gaddr 10.105.11.6/0 laddr 10.105.11.6/0
I trying to allow traffic between 2 inside interfaces with the same security level. VLAN1 and VLAN15. The are on different physical ports on the ASA. I tried to configure this through the GUI Web interface and checked ' enable traffic between two or more interfaces with the same security levels'. With this ASA version, I do not need NAT to allow this, correct?
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
I am currently troubleshooting a firewall policy on a ASA 5505. What command can enter in the CLI to enable live view of traffic been block and which traffic is been allow?In my experiences with other firewall vendors, other firewalls allow me to narrow down the source and destination, too. is there such thing on the ASA 5505?
View 6 Replies View RelatedI have ASA 5505 Firewall with security plus license, I configured two V LAN 1 and V LAN 5 as my inside V LAN for different sub net, i need to route the traffic between this two V LAN's through ASA. I configured
int vlan 1
nameif inside
Security level 100
Ip address 172.16.100.1 255.255.255.0
[Code] .........
The problem is i am not able to ping other sub net, for ex my PC is in V LAN 1 not able to ping 192.168.22.1 ... For troubleshoot i type debug icmp trace while pinging other subnet
ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4608 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4864 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5120 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5376 len=32
I turn off the firewall on my local machine.
I need to prioritize voice traffic through the ASA
priority-queue outside
tx-ring-limit 200
queue-limit 2000
Do the above values look correct? and why is the priority queue applied to the outside interface and not the inside? (or both). Also is this the part that ensures that the regular traffic does not choke the voice traffic?
class-map voip-class
match dscp ef
policy-map outsidemap
class voip-class
priority
service-policy outsidemap interface outside
Will the global policy remain which this interface policy taking priority?
I am in search of a new routers. I don't have any special task to do. Just the flow of maximum 2mb/sec data and some times video conference. However I need the Voip solution as well. I just got excited on the cisco ASA 5505 product. Can this fulfill my requirements. Can this work as the router 1841. Does this support DMVPN, SSL VPN and dynamic routing. Can I upgrade the IOS for dynamic routing purpose. Do you recommend to purchase this produe act or not instead of router ? What are the limitations of this product. If I purchase this I can use this as an router as well as strong security solution. How many ports are available for traffic flow in ASA 5505. Are all routed mode or some of them switch port.
View 1 Replies View RelatedWe have a Cisco ASA 5505 (v7.2(3)) with a "fairly" normal configuration yet we have a problem where it appears UDP/53 traffic is denied on our inside network.
here is output from our sys log:
SyslogID Source IP Dest IP Description
305006 172.18.22.3 portmap translation creation failed for udp src inside:172.18.22.156/42013 dst inside:172.18.22.3/53
To give some clarification:
172.18.22.3 is one of our DNS servers
172.18.22.156 is a device we're experimenting with.
We've bypassed the Cisco by using a 4G wireless router with this same device - and it works flawlessly.Here is a [scrubbed] copy of our config. It is what I inherited from the previous admin - I'm not sure of all its finer points (I'm not Cisco certified -- perhaps I'm just certifiable.)
: Saved
:
ASA Version 7.2(3)
!
hostname [redacted]
[code].....
I have an ASA 5505 and I setup a port with a PC connected to monitor the LAN interface. I see all the traffic from the LAN going out and traffic coming back in no problem. What I do not see the the AOL Instant Messenger traffic at all. I have WireShark on the PC and I filter for AIM traffic and I see nothing.
View 5 Replies View RelatedI have an ASA 5505 current f/w & the security plus license (to get the 3 nameif interfaces). Can I split traffic between two ISPs, (VPN traffic to one destination on a T-1 on one VLAN, and all other traffic using DSL to another VLAN) and using a different nat policy on both? I know load balacing isn't supported, only failover. I was just wondering if there was a way to make this work.
View 3 Replies View RelatedI'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99)
When I check the NAT rule, it says:
Type Source Interface AddressDynamic any outside outside.