I have added 2900 series devices in LMS3.2.1 but same are showing "unknown"device Type in a report generated from common services DC R device List.
Both are snip enabled and responding too. What is the reason behind unknown device type so those are not reflecting in any module.
36.N007010101CRRUNKNOWN37.N007010103CRRCisco 2921 Integrated Services Router38.N007010201ASRUNKNOWN
Though ASA5585-X S-20 and UCS C200 are not in LMS 4.0 supported device table, I'm wondering if there is any way to monitor these devices using LMS? Our data centre has a quite number of UCS C200 servers and two ASA5585-X S-20.
View 7 Replies View RelatedI have a Cisco Linksys WAG120N running with the firmware version 1.00.12, and it's working a quite fine.During some tests with the nmap command under Linux, I noticed that beyond the ports 80 and 433, another opened port 32764 shows up running an unknown service.This unknown service keeps running after scanning for ports between 1-65535 using nmap in stealth mode. But after querying the modem for operating system fingerprint using nmap but not in stealth mode, this port closes and the service disappears.
By using a browser to access 192.168.1.1:32764, a 12 byte "<random_prefix>.exe" file is download, and its's recognized as a text file. The file contains a "MMcSÿÿÿÿ" string, and the bytes in hexadecimal are "4d 4d 63 53 ff ff ff ff 00 00 00 00".And also, something strange happens after this unknown service goes down: Accessing the modem setup via browser, the settings displayed are different than I commonly use. the encapsulation is set to "Bridged Mode Only" instead the "RFC 2516 PPPoE", and into the Status Tab the Current Time field says "Time Zone string Error". Still in the Status Tab, in the Internet Connection information the "Login Type" is a misspelled "UNKNOW", the interface says "Connected" to a well accessible Default Gateway., the same displayed into the Routing Table Entry. Th Applications & Gaming Tab is unaccessible.After power switching the modem off and on again, everything comes back to normal again.
Cisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies View RelatedI am looking for a Cisco document that gives me the,IP through-put on 2901, 2911 and 2921 routers with Policy based routing applied.,IOS version 15.1.3TOther processes, EIGRP Stub, VLAN routing, SRST,MGCP gateway (analog and PRI).
View 1 Replies View Relatedis there any CEoIP modules (Such as NM-CEM-4TE1) for the 2900/3900 series routers?
View 2 Replies View RelatedSince i got sky broadband it's always been running super slow, the amount of times i have called them is ridiculous. So i have just been looking around on the sky address to see if i can fix it and in my Attached devices i have, the pc, an ipod touch and an unknown device. I'm wondering if this has anything to do with the slow speeds and maybe it's somehow 'stealing' my broadband. I've read a previous post of the same type but that wasnt for sky. i ran the ipconfig/all into CMD
View 1 Replies View Relatedwhat is the maximum number of Lan-to-Lan and user vpns supported in the ISR G2 2911 and 2921?
View 5 Replies View Relatedany place I can find how many tunes does the cisco 2900 series made? site to site?
View 1 Replies View RelatedI have a brand new 2901 and I'm trying to work out what licence features I have. The output of show licence shows I have ipbasek9 feature and datak9 as EvalRightToUse feature. Is BGP included in the base feature? What will happen when the datak9 evaluation period expires?
View 1 Replies View RelatedI need to do password recovery for a 2911 router. But ı can't find any documentation about it. I can be able to login at the first login, unfortunately ı logged out without changing the password. Now I can not log in and I can not open rommon with the ctrl+break key sequence.
View 6 Replies View RelatedWe had a new linux server installed at a remote office yesterday, unfortunately the guy installing the server forgot to change the IP addresses, doh. It's plugged into a C877 and I can see the port is up/up and I see the mac address using 'sh mac-address-table'. The ip address on the server is unknown but it's unlikely to be in the correct subnet for the vlan it's attached to.
Is there a way I can add an arp entry manually to the router, then ssh to the server and correct the ip address? Or is there some other way to establish the IP address of the server? It's gonna be a pain to revisit the office and there's no one there that can get into the server room to do anything from the console.
I know we can use copy & Paste, my questions are:
1. Before that, do I need to wipe out the existing confi on the brand new switch?
2. About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?
My desktop's internet connection is acting up. It's always worked fine, then all of a sudden it has stopped. I can still access MSN messenger and Paltalk, perfectly fine, and it is showing that I have an internet connection. However, when I open any of my browser windows, it cannot access the internet. My laptop and ipod are connecting fine on the wireless. I have my ethernet cable from the desktop plugged into the router, which is plugged into the modem. I CAN force the connection to work by 'talking' to the modem (using the IP address) and doing a disconnect and reconnect. This lasts for a little while, then it stops again. When I do my network map, it shows an 'unknown device' where the modem is supposed to be. When I disconnect and reconnect the modem, it changes from 'unknown device' to 'switch'.
View 19 Replies View RelatedI have a Dell 7720 148285 SE notebook. I use Windows 7 x64 Professional Edition. I downloaded and installed all the latest drivers from Dell Support site. Unfortunatelly I have got a problem.I see an unknown USB device in my Device Manager. (I have not connected any USB device to my computer except one mouse, but this is recognised correctly.)url... recognised that I do not see anywhere my Bluetooth adapter. So I think might be that is the problem.I installed the following drivers:[code[
Of course I restarted the computer every time I installed a driver but the 'Unknown device' still remained url...noticed that if I turned of my wireless connection with the keyboard buttons: Fn + F2, then this Unknown device have been disappear. After I re-enable the wireless connection with Fn+F2 buttons, then I get this error message, and my 'Unknown device' is already show up.How should I install the Bluetooth driver correctly? And which driver should I use for that?
We need to implement VLANs on my company's network. I have 3750 L3 swtich, ive setup 3 vlans for testing. ive setup SVI everything.now how do I connect it to 3com that will also use VLANs. should I set trunk port of cisco and 3com? or no need?
View 2 Replies View RelatedI recently purchased a Linksys EA4500 Dual-Band N900 Router with Gigabit and USB. Everything set up great with no problems and after a day or 2 I managed to get all home devices connected (2 laptops, 2 printers, an iphone, 1 tv, 1 blu-ray, an old desktop, and a tablet). Everything was connected right and working and I installed the Linksys app on my iPhone which let me see what devices were connected and all that. Well, last night, an unknown device showed up as a connected device. It's labeled as: android_(insert string of characters) and has a MAC address. I've tried and tried to identify what this device is and I can't. Everything else on our network is still showing up independently of that device. I'm worried that someone using our connection and possibly putting our device security at risk. What can I do to A) try to identify what the device is and B) if it is an intruder, block it's access.
View 9 Replies View RelatedI'm running on LMS 3.2 and RME 4.3.0 and one type of device was not recognized.this is NME-X-23ES-1G (IOS : 12.2(35)SE5) in a 3825 url... this module is supported with the OID 1.3.6.1.4.1.9.1.703,but in the device center I've found something which seems to be the right equipement :
- Cisco Interfaces and modules
- Cisco Network Modules
- Cisco 2800,3800 series 23-port EtherSwith Service module with OID 1.3.6.1.4.1.9.1.664
I have the WRT400N router with the latest firmware. Recently I have noticed a device in my DHCP that I do not recognize. It is not device I own (believe me, I have racked my brain and confirmed) as it shows as an Acer pc. I cannot ping the IP address however. I have rebooted my router several times thinking maybe it's a former connected device but saved in memory but it keeps coming back. I am thinking possibly it is someone hi-jacking my Internet, but not sure. I am using WEP security but it shows a LAN connection which is strange for a wireless device. The only hard wired pc is my HP.
View 3 Replies View RelatedI've buy a SRP500 Series Router (ADSL 2+).My ISP need RFC1483 Routed with LCC encapsulation type but this router dont have this type of encapsulation available in WAN settings. What can i do to use this device with my ISP adsl connection ?
View 4 Replies View RelatedThe Release Notes for 7.0.116.0 of WLC 5500 has a table which title is "Client Type", and it shows wireless adapters. My question is,
what kind of customer means? Wireless clients or clients for an specific application? If it was the first option, does it mean tha just this adapters could connect to my wireless network?
It may be a coincidence but my Broadcom Network Adapter 802.11g stopped working after trying to fix 'unknown device' in Device Manager (It was working perfectly before this).OS: Windows 7 Starter on 'BenQ Joybook Lite U105'.I tried the Windows Network trouble shooter and it didn't work (saying there may be a problem with the driver. I uninstalled the driver and re-installed it (including a possibly newer one) and it didn't work. Within 'Network Connections" the Broadcom wireless adapter is shown as 'disabled' I R-clicked to enable it, a window popped up saying it was enabled but it still showed as being disabled. My feeling is that something is preventing it from being enabled, logically, I would guess. Also went to 'Component Services' and ether started or restarted everything with the word network on it still no luck..My Google search on an other pc , now on day 3, couldn't find anything. (BTW the 'unknown device' which according to the icon, seems to be the joybook itself, is still not fixed and still listed as 'unknown device').
View 4 Replies View RelatedI faced some problems when updating the device packages on the LMS 3.2 server. Therefore, I really need device packages of switch 3750, router 2900 and router 3900 series. I had tried update online but could't view any devices.
View 1 Replies View RelatedI am trying to install Cisco Connect for my E1000 but I get the following error each attempt "An HNAP Call to the device failed for unknown reasons" I've already updated the router to 2.1 version of the Firmware.
Full Details
Error code: 82BD0305Error description: An HNAP call to the device failed for an unknown reason.Model name: unknownModel number: E1000Serial number: unknownFirmware version: unknownOperating system: Windows 7 SP 1Software version: 1.3.11069.2Connection type (WAN): unknownIP address (LAN): unknownIP address (WAN): unknownComputer IP address: 192.168.1.132
I am facing a very big problem with site to site vpn on cisco 2900 ios.i configured the vpn and when i ping from router itself to destination ip with source as lan interface , VPN works, no problem.but when i connect any computer directly to router's lan interface to initiate traffic , it doesnot work at all. and on computer's lan i see yeloow sign.
mtu is 1500, speed is auto (i tried chaging also) , duplex is auto ( i tried changing also) , thoguh firewall on pc should not affect but still i disabled it.since their is no problem with vpn config as vpn comes up when i initiate ping from router itself but i dont know why it is not working from lan.do we need any inspect icmp on this router also ? or any policy modification to pass traffic across the interfac on router is required ?
i was useinf c2900k9-15.0(M4).bin and i upgraded it to 15.3 which is lated to get reed of any bug .lastly , i connected two laptops directly to router's gi0/0, g0/1 interface to ping from one laptop to another but this also did not work.
If there is a router ISRG2 2900 with SEC license and without HSEC license, there is a limit in count of cumulative encrypted VPN tunnels of 225. Which commands can show us a number of current tunnels on the router, so we can see if we are near this limit of 225?
View 4 Replies View RelatedOur LMS DCR include more then 1200 devices, ( ASR 1000, CISCO 2600, 2800 advanced ip services IOS etc. )Everything is working well except the IP SLA device table is empty.I can not choose any device from this table.How can i import/add devices to this table/database automatically ?
View 2 Replies View RelatedI have some LSA type 5, I want to change it from type 5 to type 3 before send to another Area, How can i do it?
View 1 Replies View RelatedGot following problem with an LMS server that is installed without DNS server in the network, because this customer doesnt own and doesnt need any.
CS,CM,CV is working and contains devices, but RME (cannot connect to db) and DFM (TIS URN found) not. pdshow and dbRestoreOrig.pl after calling, hangs for ever.
To loose no further time with troubleshooting, I want to reinstall LMS from the scratch.
But I dont want to setup an DNS server just for resolving the only IP-Adresse from LMS server for self purpose only. Do I need an entry in driversetchosts for LMS server itself?
<IP> <Name> <Name>.<Fake-and-complete-unimportend-domin>
Do I need a fake-Domain? or can Domain be empty?
OS=Win2008,R1,SP1 as Standaloneserver (WORKGROUP)
i tried to restore backup from LMS3.2.1(windows) to LMS4.2 virtual appliance. once the back up is completed, the home page takes forever to load. i opened TAC case, and the only way out seems to be configuring from scratch after importing the devices. i, imported the devices and this didn't cause any problem. But, making the configuration from scratch is something i would like to avoid if possible.
View 1 Replies View Relatedcreate a scheduled task in LMS. In this task I would like to regularly check time on all network devices in LMS and generate a rapport about this that would be sent to e-mail. All network devices have the same NTP server. How can I create this task? LMS version is 3.2 SP1.
View 4 Replies View RelatedI want to forward syslog messages that I receive in my Cisco Works server to another server,what is the best way to accomplish this. I'm running LMS3.2 on Solaris 10.
View 3 Replies View Relatedin RME->Software Management-> Software Distribution -> By Devices [advanced], what is the file format we should have here, when we try to deploy many IOS images at once?
View 1 Replies View Related