i tried to restore backup from LMS3.2.1(windows) to LMS4.2 virtual appliance. once the back up is completed, the home page takes forever to load. i opened TAC case, and the only way out seems to be configuring from scratch after importing the devices. i, imported the devices and this didn't cause any problem. But, making the configuration from scratch is something i would like to avoid if possible.
View 1 Repliesin LMS3.2.1 we have NMSRoot/log/syslog.log where syslogs are being logged actively from managed devices. i couldn't find the same in LMS4.2. I am configuring LMS4.2 from scratch and in the hope of making the trasition from old LMS3.2.1 to LMS 4.2, I am planning assigning the old LMSs IP to the new one. basically changing the IP address of LMS4.2.
View 10 Replies View RelatedI'm trying to restore backup after upgrading Cisco Prime v4.1 to v4.2. However, getting the following error in the log. [code] The log shows the error is a continuous one and affraid it may be a loop. Currently my restore progress is stuck at 70%RME restoration.[code]
View 2 Replies View RelatedGot following problem with an LMS server that is installed without DNS server in the network, because this customer doesnt own and doesnt need any.
CS,CM,CV is working and contains devices, but RME (cannot connect to db) and DFM (TIS URN found) not. pdshow and dbRestoreOrig.pl after calling, hangs for ever.
To loose no further time with troubleshooting, I want to reinstall LMS from the scratch.
But I dont want to setup an DNS server just for resolving the only IP-Adresse from LMS server for self purpose only. Do I need an entry in driversetchosts for LMS server itself?
<IP> <Name> <Name>.<Fake-and-complete-unimportend-domin>
Do I need a fake-Domain? or can Domain be empty?
OS=Win2008,R1,SP1 as Standaloneserver (WORKGROUP)
We are in the process of upgrading Cisco LMS 3.2 to Cisco Prime 4.2.While restoring the database, we are getting attached msg. We tried by removing security policies from folder but still the error is same.
View 1 Replies View Relatedcreate a scheduled task in LMS. In this task I would like to regularly check time on all network devices in LMS and generate a rapport about this that would be sent to e-mail. All network devices have the same NTP server. How can I create this task? LMS version is 3.2 SP1.
View 4 Replies View RelatedI want to forward syslog messages that I receive in my Cisco Works server to another server,what is the best way to accomplish this. I'm running LMS3.2 on Solaris 10.
View 3 Replies View RelatedI have a 3550 I can boot into rommon, when I type flash_init the switch freezes and shows a weird ASCII character?
View 4 Replies View RelatedCan I check I've understood the ACS backup and restoration procedure?A backup run from exec as "backup <filename> repository <repository name>" is the same command run automatically by "System Administrator -> Scheduled Backups" in the GUI, just scheduled for me...That backup is enough to completely restore ACS to its state at the time of the backup, including ACS config (Users, Devices, NDGs, etc.) and the View database (reports, historical data, etc.)It's entirely separate from the backups ACS View makes as part of it's purging action. (I only need those if I want to go way back in time, I don't need them to restore a functioning ACS with the recent reports and logs) if I still have a working ACS left after the primary dies, is it not just easier to promote the survivor to primary and then add the replacement in as a secondary and let replication restore the configs? Perhaps re-promote the new box to primary afterwards?
View 7 Replies View Relatedin RME->Software Management-> Software Distribution -> By Devices [advanced], what is the file format we should have here, when we try to deploy many IOS images at once?
View 1 Replies View RelatedOn our CiscoWorks 2000 installation, running on Solaris with LMS3.2 and RME4.3.1, we noticed a few weeks ago, that the job "Inventory Collection" needs more and more time to finish. At the moment the job execution time is as high as 8 hours, compared to 3 hours before. When we look at the network traffic during job execution, we see after the collection phase (~3h) several hours with no traffic together with a very high CPU load. I mean to remember that this job used to complete around 15 minutes after data collection phase. Restarting the application and rebooting the system didn't work.When we look in to the IC_Server.log, we find devices with a completion time of over 20'000 seconds. Increasing from day to day. [code]
Affected devices are Cisco Nexus 5548P. We tried to delete/add these devices. That works for a few days, then the runtime starts to increase again.
Are we hitting a bug? And is it possible, as a workaround, to exclude devices from only the Inventory Collection?
I noticed that I cannot remotely check the Topology Services in Ciscoworks LMS 3.2. I have attached a screenshot of the error for reference. When I access Topology Services on the server itself, everything works well.
View 5 Replies View RelatedI think I understand purging in ACS5 now:Purging occurs when the database either gets too large or when data is too old (up to 12 months, although I assume you can leave the setting blank and no age related purging takes place?)Data is purged by making incremental backups and deleting the backed up data from the local database until the size/age pressure is relieved.So, my question is, how do I later look at the purged data? If I suddenly need to look at logs from last year what am I supposed to do? If I restore it surely I'm just going to go over the size limit again and it'll just get purged, no?
View 6 Replies View RelatedI have got a working 5505 running 8.3.1 firmware and 6.3.1 ASDM.I have now purchased a second unit and ensured that both units are running the same firmware levels etc.
I have via the ASDM created a backup of the working units configuration, and now i want to load this configuration onto the second unit.I have connected the consiole cable up to the second unit and tried pasting in the contents of the configuration file but no joy.I want to ensure that my configuration will work on this unit before i configure the two units in Active/Passiove configuration.
I have added 2900 series devices in LMS3.2.1 but same are showing "unknown"device Type in a report generated from common services DC R device List.
Both are snip enabled and responding too. What is the reason behind unknown device type so those are not reflecting in any module.
36.N007010101CRRUNKNOWN37.N007010103CRRCisco 2921 Integrated Services Router38.N007010201ASRUNKNOWN
i've the following problem. Check device credential verification job shows "Error performing SNMP operation" for a cisco 3750 configured with snmpv3.On the switch i can see that the lms can access the switch via snmpv3. Also cisco view works fine. Bug CSCsm89609 describe the problem but it should be fixed in RME 4.3. We are running 4.3.1.
View 9 Replies View RelatedCreating an image is almost always a success. However, when restoring, sometimes the process gets stuck somewhere (the client reboots prematurely if that happens) and more than often the clients can't boot into Windows anymore.All clients have the exact same hardware.Now I know the image can't be the problem, as I've restored this exact image to a client two days ago and it booted perfectly fine. Everything worked.I tried to image two clients at the same time. The first thing I noticed was that the method used was NFS and not UDPCAST, which it should be. Now I know it wasn't using multicast because the imaging went asynchronous.
View 14 Replies View RelatedIt's not wireless but the leads and cables are all plugged in?!
View 11 Replies View RelatedCant find the speeking result/cause of 4 and 1 in the example below, that are defined as enums in the MIBs normaly. Where can I access the result of "snmptranslate -M<MIB-dirs> -m ALL -Td <ps-status/test-oid>" if this is implemented in LMS overall? What are the OIDs from Cisco's ps-status/test, if the translation of MIB-enums is not implented?
Event_Description
StateNotNormalDevice IP
x.y.z.1Device Type
Switches and HubsFault Last Updated At
06-Nov-2012 16:12:49Component
[code]....
With lms 3.2 during installation we can choose what to install i.e. not install DFM or IPM.
How can we do this in the new release 4.0 of the LMS bundle. I saw no options for it during installation of the new server.
Cisco release the Cisco Prime LMS 4.1 on Aug. 2011. I download the lms4.1 from cisco and install it, but the lms4.1's evaluation license expire date is Oct. 28 2009. So my license already expired after I install the LMS4.1.
View 1 Replies View RelatedRestoring a BARS file created from one server onto a different server?
View 6 Replies View RelatedI would like to upgrade LMS4.2 to PI1.2. According to Cisco this is a minor upgrade (requires the SAS code) and can be downloaded from the Cisco portal for free. My question: Can I still reuse the license and the B2B cisco support I use for my LMS4.2 ?
I will also upgrade WCS7.0.x to PI1.2. Will there finally be 1 server running 1 merged software, or will there be 2 servers one for WCS >> PI and one for LMS >> PI ?
We migrated to LMS4.2 and i created new credential set and set it as the default. However, the new cdredential set applies only to newly added devices no to the migrated devices. for example when i run device credential verfication for a migrated device, the username used my LMS is "cwuser" as opposed to the one i created with the new credential sets. how can i make this new credentila set be applicable to all devices?
View 3 Replies View RelatedIn our organisation we have multiple Nexus 5000 switches, which Cisco LMS 4.2.2 cannot get the running-config and startup-config from with the Archive Management process. When it does try to get them, I get a error as follows:
*** Device Details for SF-DERA-01 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,SCP
[Code].....
I reinstalled CiscoWorks LMS (Windows 2008 R2) updated th LMS with all availible devicepackages and imported all devices with a xml bulk import of the former installation. Now I am frustrated.... because after the reinstallation LMS has problems collecting the inventory data.The inventory collection for one local device (Cisco WS-C3560-8PC-S) starts and nevers stops.... I have to stop the ICserver to stop the inventory collection.
I have only 4 of nearly 1800 devices where it was possible to collect the inventory information.All the rest is supposed to unreacheable...Reports> Inventory>Management Status>Unreachable Devices.But if I take one of the devices which is reported to be unreacheable and do a device diagnostic (Monitor> Troubleshooting Tools> Troubleshooting Workflows) says it is reacheable...
The inventory does not appear in the "Collector Status"?
I've run into an interesting problem trying to migrate my production config from my redundant ACE20's (A2(3.4)) to the new ACE30's (Tried (A4(1.0) and A5(1.0)). Everything on the ACE30 is working fine with a base config, but when the restore all is run from the ACE20 backup (backup all), the SSL files are not restored and return errors. All the contexts are restored correctly, along with the startup-config, but the running config fails due to no SSL.
All the crypto certs/keys are exportable and are present in the backup .tgz file.
My cisco works LMS3.2 is not showing recent configuration of my Cisco devices. also it dont show any change report on last 24 hours or even if i select x number of day, looks like its not saving any changes made on devices.
today i logged in and cisco ASA was showing this in status as well Configuration Last Archived Time May 03 2012 11:27:46 EDT on checking i could see it is same date when cisco ASA was added in cisco works. do i need to click some where for auto update configuration changes and latest confoguration in cisco works setting?
I have a very special usecase with migrating devices from LMSv2.6 to v4.1 using DCR bulk import that was maintained manualy, not by discovering.The special thing is each device has its own SNMP-community and its about 1500 devices.RME discovery works fine, but I get the devices not discovered by DCR (CSDiscovery), because I need a minimal DCR discovery configration containing Seed and SNMP-settings. So I activated DCR as seed, but cant skip SNMP settings without an entry. But in this case I would need 1500 SNMP-lines that would be very unhandy. is in CSDiscovery-Settings a possibility to can leave SNMP settings untouched so it takes the credentials from the DCR, to can start DCR discovery?
View 6 Replies View RelatedI am having a strange issue deploying universalk9-150-2.SE2 to our 2960S. All the switches are stand alones.LMS gives an error when asking to upgrade the image but the fact is that the new software wents through - if I manually reload the switch everything is fine.why is RME showing an error if the new image seems to have been deployed?
View 23 Replies View RelatedWho can give me a SNMPv3 configuration template.I tried many times has been a problem
View 5 Replies View RelatedI have installed Cisco Prime Infrastructure 1.2 separately from LMS4.2. LMS4.2 is in production. I just want to run PI1.2 in parallel with LMS4.2 before migrating to PI1.2. Currently I have LifeCycle permanent license. Why don't I have the assurance lfeature set license. it is running in evaluation mode.
View 1 Replies View RelatedThis is a WS-C4510R+E with a Sup 7-E running 03.02.02.SG enterprise.
I increased SNMP timeout to 10 seconds to no avail.