I am having a strange issue deploying universalk9-150-2.SE2 to our 2960S. All the switches are stand alones.LMS gives an error when asking to upgrade the image but the fact is that the new software wents through - if I manually reload the switch everything is fine.why is RME showing an error if the new image seems to have been deployed?
View 23 RepliesCant find the speeking result/cause of 4 and 1 in the example below, that are defined as enums in the MIBs normaly. Where can I access the result of "snmptranslate -M<MIB-dirs> -m ALL -Td <ps-status/test-oid>" if this is implemented in LMS overall? What are the OIDs from Cisco's ps-status/test, if the translation of MIB-enums is not implented?
Event_Description
StateNotNormalDevice IP
x.y.z.1Device Type
Switches and HubsFault Last Updated At
06-Nov-2012 16:12:49Component
[code]....
I have a brand new 2960S-48TS-L, plain vanilla with no extra module/boards etc. It boots up ok (the installed version is 12.2 (55) SE5) but then constantly cycles the following error, and doesn't accept any input whatsoever. After 5-10 minutes of cycling the error, the switch reloads and starts the process again.
PCIE0: link is NOT up.
--------------CPU's PCIe SDR Registers--------------------
PE_DLPSET = 00401000
PE_UTLSET1 = 00000000
[Code]......
With lms 3.2 during installation we can choose what to install i.e. not install DFM or IPM.
How can we do this in the new release 4.0 of the LMS bundle. I saw no options for it during installation of the new server.
Cisco release the Cisco Prime LMS 4.1 on Aug. 2011. I download the lms4.1 from cisco and install it, but the lms4.1's evaluation license expire date is Oct. 28 2009. So my license already expired after I install the LMS4.1.
View 1 Replies View RelatedI would like to upgrade LMS4.2 to PI1.2. According to Cisco this is a minor upgrade (requires the SAS code) and can be downloaded from the Cisco portal for free. My question: Can I still reuse the license and the B2B cisco support I use for my LMS4.2 ?
I will also upgrade WCS7.0.x to PI1.2. Will there finally be 1 server running 1 merged software, or will there be 2 servers one for WCS >> PI and one for LMS >> PI ?
i tried to restore backup from LMS3.2.1(windows) to LMS4.2 virtual appliance. once the back up is completed, the home page takes forever to load. i opened TAC case, and the only way out seems to be configuring from scratch after importing the devices. i, imported the devices and this didn't cause any problem. But, making the configuration from scratch is something i would like to avoid if possible.
View 1 Replies View RelatedWe migrated to LMS4.2 and i created new credential set and set it as the default. However, the new cdredential set applies only to newly added devices no to the migrated devices. for example when i run device credential verfication for a migrated device, the username used my LMS is "cwuser" as opposed to the one i created with the new credential sets. how can i make this new credentila set be applicable to all devices?
View 3 Replies View RelatedIn our organisation we have multiple Nexus 5000 switches, which Cisco LMS 4.2.2 cannot get the running-config and startup-config from with the Archive Management process. When it does try to get them, I get a error as follows:
*** Device Details for SF-DERA-01 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,SCP
[Code].....
I reinstalled CiscoWorks LMS (Windows 2008 R2) updated th LMS with all availible devicepackages and imported all devices with a xml bulk import of the former installation. Now I am frustrated.... because after the reinstallation LMS has problems collecting the inventory data.The inventory collection for one local device (Cisco WS-C3560-8PC-S) starts and nevers stops.... I have to stop the ICserver to stop the inventory collection.
I have only 4 of nearly 1800 devices where it was possible to collect the inventory information.All the rest is supposed to unreacheable...Reports> Inventory>Management Status>Unreachable Devices.But if I take one of the devices which is reported to be unreacheable and do a device diagnostic (Monitor> Troubleshooting Tools> Troubleshooting Workflows) says it is reacheable...
The inventory does not appear in the "Collector Status"?
in LMS3.2.1 we have NMSRoot/log/syslog.log where syslogs are being logged actively from managed devices. i couldn't find the same in LMS4.2. I am configuring LMS4.2 from scratch and in the hope of making the trasition from old LMS3.2.1 to LMS 4.2, I am planning assigning the old LMSs IP to the new one. basically changing the IP address of LMS4.2.
View 10 Replies View RelatedI have a very special usecase with migrating devices from LMSv2.6 to v4.1 using DCR bulk import that was maintained manualy, not by discovering.The special thing is each device has its own SNMP-community and its about 1500 devices.RME discovery works fine, but I get the devices not discovered by DCR (CSDiscovery), because I need a minimal DCR discovery configration containing Seed and SNMP-settings. So I activated DCR as seed, but cant skip SNMP settings without an entry. But in this case I would need 1500 SNMP-lines that would be very unhandy. is in CSDiscovery-Settings a possibility to can leave SNMP settings untouched so it takes the credentials from the DCR, to can start DCR discovery?
View 6 Replies View RelatedWho can give me a SNMPv3 configuration template.I tried many times has been a problem
View 5 Replies View RelatedI have installed Cisco Prime Infrastructure 1.2 separately from LMS4.2. LMS4.2 is in production. I just want to run PI1.2 in parallel with LMS4.2 before migrating to PI1.2. Currently I have LifeCycle permanent license. Why don't I have the assurance lfeature set license. it is running in evaluation mode.
View 1 Replies View RelatedThis is a WS-C4510R+E with a Sup 7-E running 03.02.02.SG enterprise.
I increased SNMP timeout to 10 seconds to no avail.
May I know what the redistribution is? Is it the redistribution of routing information between different AS numbers ?
View 4 Replies View RelatedWe tried to distribute the softwer ( 12.4.23 ) via LMS 4.1 but we got the following message:Device is locked for exclusive access.The supported protocols for image transfer are: TFTP
SWIM1001: The input parameters to the Image Distribution/Image Import/Image Activate are invalid. You may have used incorrect Device Data for this task. Check the application log file for more details.
Device Upgrade Result : Failed
End Time:Mon Mar 05 15:53:17 CET 2012
Earlier we used LMS 3.2 and it gave same messages,The hardver is cisco 2620XM and actually used IOS is c2600-advipservicesk9-mz.124-3.bin ,We need to upgrade large number of devices via LMS.
I'm currently unable to upgrade certain devices since Cisco Prime incorrect believes there is not enough room in the flash partition.For example.
Getting the following error messsage trying to upgrade some Cisco 871 routers: "Catastrophic - SWIM1200: Selected Flash partition requires minimum (28 MB) to upgrade selected software/image."The images are around 18 MB in size. Why does Cisco Prime thinks its 28 MB in size? Bug?
I opened a discussion a while ago and had some great feedback but I am still racking my brains to figure this out,I have 2 routers each with a dedicated connection to the same ISP. I am using MED to influence my advertisements to the provider,I have 2 core switches (6509) with multiple vlans, each vlan has an HSRP address of .10 shared by the switches
My routers and switches are using iBGP to communicate. Both routers connect to vlan 1 on the core switches,I want to influence my traffic from the vlans to go to specific routers, so that I utilize both routes at all times (when possible), ensuring symmetric routing at the same time.
I think I have the following options
- PBR, I'd set this on the routers fastethernet interfaces and match based an two different ACLs
set the next hop as the ISP router 1 when matching ACL 1
set the next hop as the ISP router 2 when matching ACL 2
My concern is if I lose a link (say to ISP router 1), all traffic matched by ACL 1 is blackholed
- HSRP was suggested to me.
configure 2 standby groups on the routers with different priorities
allocate different HSRP addresses matching each vlan (to act as a core switch default gateway)
My concern here is I'd need the routers HSRP virtual IP addresses as the BGP neighbors on the core switches?
I have Westell Ultraline series3 modem/router , the problem is i can only connect to the router/internet if i enter the IP address and DNS manually , which is not much of a problem except I have a vonage phone and can't type the ip address in it , so here's how the settings looks like , let me know what i should be changing
[IMG]file:///C:/Users/GL/Pictures/Network.png[/IMG][IMG]file:///C:/Users/GL/Pictures/Network.png[/IMG]
I have been able to get EIGRP working successfully in the lab like I want.
Attached is the network overview:
We have a Data Center and Corporate office connected via Point to Point Fiber link, eventually we will have two of theseTwo 4948E switches in the Data center acting as cores setup with GLBPCorporate Office has a 3750X acting as a coreCurrently two 4948E's are connected to each other via Port Channel and a L2 trunkTwo set of ASA 5520's one acting as a firewall and for Cisco Any Connect and second for site to site VPN
What is the best way/pratice that I can distribute this DMZ via EIGRP? Should I just leave it static on the core like this?
We are running with Cisco ACS v4.0 AAA server, Here I need the use of Proxy distribution table.
View 5 Replies View RelatedI have Wireless LAN Controller 4400 running. Currently all 50 APs are running at one port of WLC. I have studied on Cisco site, that its best to run 24 APs per port of WLC and total 48 in total. My all APs are running at one port. is there any issue if i run all 50APs on one port and is this any bottleneck?Also if i want to shift half APs to second port, What will be configuration for WLC?
View 6 Replies View Relatedin RME->Software Management-> Software Distribution -> By Devices [advanced], what is the file format we should have here, when we try to deploy many IOS images at once?
View 1 Replies View RelatedI got a 5MBps Lease Line Connection via FAST ETHERNET PORT. i got a Cisco 1841 Router.
I want to distribute bandwidth in this ratio 2MBps/2MBps/1MBps
2MBps = Office Connection
2MBps = Computer Laboratory Connection
1MBps = WIFI Connection
1841 has only 2 Fast Ethernet ports
so im planning to add up a 2modules of 2-Port Fast Ethernet High-Speed WIC for Cisco Integrated Services Routers
i am using Cisco ASA5510 Firewall on my network at the distrubution Layer . The Private IP Address is in the network for Users and PAT is use.I have a client who has configured the RDP on port2000. when the Users behind the Firewall in my Network tried RDP it does not work it shows configuring remote Desktop only. i am able to telnet the Client said server with port 2000 but unable RDP.Is any changes required on my firewall as a tesult the RDP works.
View 8 Replies View RelatedWe currently support multiple companies' infrastructure on a single Prime Infrastructure 1.2 server. We are using lifecycle licenses. Is it possible to assign licenses to various Businesses? For example, can I upload 100 licenses for Company-X and 100 licenses for Company-Y and when adding devices into Prime, tell it which licenses pool to pull from? Could something like this be accomplished with virtual domains?
View 3 Replies View Relatedusing the 55xx as a L3 Distribution switch or even as a Core. By enabling the L3 features does it allow you enabled L3 SVI's for VLAN interfaces or are there interfaces on the daughter card that are used for routing instead?
View 5 Replies View RelatedWe are using CISCO Catalyst 6500 switches as collapsed core/distribution switches (2 layer architecture). I want to connect approximatly 10 application servers to the network. Can I connect the servers directly to the catalyst 6500 switches using WS-X6148E-GE-TX line cards? The other option is to use access switchs and then connect the servers to the catalyst 6500 through access switch(Catalyst 3750).
View 6 Replies View RelatedWe have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
View 1 Replies View RelatedImagine I am designing a small network with a C2900 router running OSPF and in the future BGP with service provider. Please see attached diagram.The router is connected to (2) C3750 Layer 3 distribution switches. Then one C3560 layer 2 switch to serve future IP phone users and desktops.
Question:
a)If I connect the router interface to the (2) 3750 switches, if I make the router interface fa0/0 and fa0/1 as a trunk to accomodate VLAN 200 and other future VLANs, don't I have a problem with overlapping networks between router interface fa0/0 and fa0/1?
b)Alternatively, I could make the Router1 fa0/0 and fa0/1 configured with IP addresses and advertised in OSPF. Then the SW1 fa0/24 and and SW2 fa0/24 I could make as 'no switchport and create a routed interface port' with IP addresses, also running OSPF. Question is, from a scalable design perspectie, would you create 2 management networks and use those when assigning the IP addresses for Router1 fa0/1 and fa0/2? Because again Router1 fa0/1 and fa0/2 obviously need to be placed on different networks to avoid overlapping. So my question is more about proper network planning design to make this scalable to accomodate future VLANs in the future.Using trunks between the Router1 and SW1 option:
Router1
int fa0/0
description connection to SW1
no ip add
int fa0/0.200
[code]....
I have been working on redesign of our network which was very challenging but almost there.We have a limited budget of around £20k(32k Dollor) Max. The cabling has been done before my time and it is very messy and cheap so you can not do a proper cisco hierarchical model at all.I can not have multiple links from each access layer switch to the core/distribution and as a result i had to connect some access switches together to introduces redundancy in a nutshell,we have two buildings, main building which has the server room in it and the other building which is just bunch of office. i have introduced a partial mesh on the normal building and have tried to introduce full mesh on the main building .
View 9 Replies View RelatedThe two stacked Cisco 3750G Access switches on a particular floor in my coy just lost connectivity to the distribution Switch this morning. This meant that all Users connected to it couldnt connect to the Internet nor access local network resources.I couldn't ping the Switch IP, I couldn't also access the Switch via Console port. Each time I tried to gain access via the console port, I keep getting "Authentication Failed" message.What should I do next? How do I gain access to the Switch?
View 1 Replies View Related