I have Westell Ultraline series3 modem/router , the problem is i can only connect to the router/internet if i enter the IP address and DNS manually , which is not much of a problem except I have a vonage phone and can't type the ip address in it , so here's how the settings looks like , let me know what i should be changing
[IMG]file:///C:/Users/GL/Pictures/Network.png[/IMG][IMG]file:///C:/Users/GL/Pictures/Network.png[/IMG]
May I know what the redistribution is? Is it the redistribution of routing information between different AS numbers ?
View 4 Replies View RelatedWe tried to distribute the softwer ( 12.4.23 ) via LMS 4.1 but we got the following message:Device is locked for exclusive access.The supported protocols for image transfer are: TFTP
SWIM1001: The input parameters to the Image Distribution/Image Import/Image Activate are invalid. You may have used incorrect Device Data for this task. Check the application log file for more details.
Device Upgrade Result : Failed
End Time:Mon Mar 05 15:53:17 CET 2012
Earlier we used LMS 3.2 and it gave same messages,The hardver is cisco 2620XM and actually used IOS is c2600-advipservicesk9-mz.124-3.bin ,We need to upgrade large number of devices via LMS.
I'm currently unable to upgrade certain devices since Cisco Prime incorrect believes there is not enough room in the flash partition.For example.
Getting the following error messsage trying to upgrade some Cisco 871 routers: "Catastrophic - SWIM1200: Selected Flash partition requires minimum (28 MB) to upgrade selected software/image."The images are around 18 MB in size. Why does Cisco Prime thinks its 28 MB in size? Bug?
I opened a discussion a while ago and had some great feedback but I am still racking my brains to figure this out,I have 2 routers each with a dedicated connection to the same ISP. I am using MED to influence my advertisements to the provider,I have 2 core switches (6509) with multiple vlans, each vlan has an HSRP address of .10 shared by the switches
My routers and switches are using iBGP to communicate. Both routers connect to vlan 1 on the core switches,I want to influence my traffic from the vlans to go to specific routers, so that I utilize both routes at all times (when possible), ensuring symmetric routing at the same time.
I think I have the following options
- PBR, I'd set this on the routers fastethernet interfaces and match based an two different ACLs
set the next hop as the ISP router 1 when matching ACL 1
set the next hop as the ISP router 2 when matching ACL 2
My concern is if I lose a link (say to ISP router 1), all traffic matched by ACL 1 is blackholed
- HSRP was suggested to me.
configure 2 standby groups on the routers with different priorities
allocate different HSRP addresses matching each vlan (to act as a core switch default gateway)
My concern here is I'd need the routers HSRP virtual IP addresses as the BGP neighbors on the core switches?
I have been able to get EIGRP working successfully in the lab like I want.
Attached is the network overview:
We have a Data Center and Corporate office connected via Point to Point Fiber link, eventually we will have two of theseTwo 4948E switches in the Data center acting as cores setup with GLBPCorporate Office has a 3750X acting as a coreCurrently two 4948E's are connected to each other via Port Channel and a L2 trunkTwo set of ASA 5520's one acting as a firewall and for Cisco Any Connect and second for site to site VPN
What is the best way/pratice that I can distribute this DMZ via EIGRP? Should I just leave it static on the core like this?
We are running with Cisco ACS v4.0 AAA server, Here I need the use of Proxy distribution table.
View 5 Replies View RelatedI have Wireless LAN Controller 4400 running. Currently all 50 APs are running at one port of WLC. I have studied on Cisco site, that its best to run 24 APs per port of WLC and total 48 in total. My all APs are running at one port. is there any issue if i run all 50APs on one port and is this any bottleneck?Also if i want to shift half APs to second port, What will be configuration for WLC?
View 6 Replies View Relatedin RME->Software Management-> Software Distribution -> By Devices [advanced], what is the file format we should have here, when we try to deploy many IOS images at once?
View 1 Replies View RelatedI got a 5MBps Lease Line Connection via FAST ETHERNET PORT. i got a Cisco 1841 Router.
I want to distribute bandwidth in this ratio 2MBps/2MBps/1MBps
2MBps = Office Connection
2MBps = Computer Laboratory Connection
1MBps = WIFI Connection
1841 has only 2 Fast Ethernet ports
so im planning to add up a 2modules of 2-Port Fast Ethernet High-Speed WIC for Cisco Integrated Services Routers
i am using Cisco ASA5510 Firewall on my network at the distrubution Layer . The Private IP Address is in the network for Users and PAT is use.I have a client who has configured the RDP on port2000. when the Users behind the Firewall in my Network tried RDP it does not work it shows configuring remote Desktop only. i am able to telnet the Client said server with port 2000 but unable RDP.Is any changes required on my firewall as a tesult the RDP works.
View 8 Replies View RelatedI am having a strange issue deploying universalk9-150-2.SE2 to our 2960S. All the switches are stand alones.LMS gives an error when asking to upgrade the image but the fact is that the new software wents through - if I manually reload the switch everything is fine.why is RME showing an error if the new image seems to have been deployed?
View 23 Replies View RelatedWe currently support multiple companies' infrastructure on a single Prime Infrastructure 1.2 server. We are using lifecycle licenses. Is it possible to assign licenses to various Businesses? For example, can I upload 100 licenses for Company-X and 100 licenses for Company-Y and when adding devices into Prime, tell it which licenses pool to pull from? Could something like this be accomplished with virtual domains?
View 3 Replies View Relatedusing the 55xx as a L3 Distribution switch or even as a Core. By enabling the L3 features does it allow you enabled L3 SVI's for VLAN interfaces or are there interfaces on the daughter card that are used for routing instead?
View 5 Replies View RelatedWe are using CISCO Catalyst 6500 switches as collapsed core/distribution switches (2 layer architecture). I want to connect approximatly 10 application servers to the network. Can I connect the servers directly to the catalyst 6500 switches using WS-X6148E-GE-TX line cards? The other option is to use access switchs and then connect the servers to the catalyst 6500 through access switch(Catalyst 3750).
View 6 Replies View RelatedWe have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
View 1 Replies View RelatedImagine I am designing a small network with a C2900 router running OSPF and in the future BGP with service provider. Please see attached diagram.The router is connected to (2) C3750 Layer 3 distribution switches. Then one C3560 layer 2 switch to serve future IP phone users and desktops.
Question:
a)If I connect the router interface to the (2) 3750 switches, if I make the router interface fa0/0 and fa0/1 as a trunk to accomodate VLAN 200 and other future VLANs, don't I have a problem with overlapping networks between router interface fa0/0 and fa0/1?
b)Alternatively, I could make the Router1 fa0/0 and fa0/1 configured with IP addresses and advertised in OSPF. Then the SW1 fa0/24 and and SW2 fa0/24 I could make as 'no switchport and create a routed interface port' with IP addresses, also running OSPF. Question is, from a scalable design perspectie, would you create 2 management networks and use those when assigning the IP addresses for Router1 fa0/1 and fa0/2? Because again Router1 fa0/1 and fa0/2 obviously need to be placed on different networks to avoid overlapping. So my question is more about proper network planning design to make this scalable to accomodate future VLANs in the future.Using trunks between the Router1 and SW1 option:
Router1
int fa0/0
description connection to SW1
no ip add
int fa0/0.200
[code]....
I have been working on redesign of our network which was very challenging but almost there.We have a limited budget of around £20k(32k Dollor) Max. The cabling has been done before my time and it is very messy and cheap so you can not do a proper cisco hierarchical model at all.I can not have multiple links from each access layer switch to the core/distribution and as a result i had to connect some access switches together to introduces redundancy in a nutshell,we have two buildings, main building which has the server room in it and the other building which is just bunch of office. i have introduced a partial mesh on the normal building and have tried to introduce full mesh on the main building .
View 9 Replies View RelatedThe two stacked Cisco 3750G Access switches on a particular floor in my coy just lost connectivity to the distribution Switch this morning. This meant that all Users connected to it couldnt connect to the Internet nor access local network resources.I couldn't ping the Switch IP, I couldn't also access the Switch via Console port. Each time I tried to gain access via the console port, I keep getting "Authentication Failed" message.What should I do next? How do I gain access to the Switch?
View 1 Replies View RelatedThis is existing network diagram and find attached file for configuration of Router and L3 Switch:ISP provided 6 Mbps internet access link with ethernet Handoff which is terminated over Cisco 1841.ISP also provided pool of 30 Public ip's 125.63.74.33 /27 , range from 125.63.74.34 to 125.63.74.62.In my current setup, all Inside to ouside traffic going out through 125.63.74.34 public ip because this public-ip NAT overload with Router F0/1 interface.
1) I want to divide 6 Mbps link physically into three parts 2Mbps, 2Mbps, 2Mbps for three VLANs.
2) I want to also configure each vlan IN/OUT traffic with different Public ip. is it possible or not ?
Vlan2 = 172.25.162.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.40
Vlan3 = 172.25.163.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.41
Vlan4 = 172.25 164.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.42
How can i configure above desired setup with CBWFQ
I had a lot of questions when I began planning a pair of Nexus 7000 switches as a replacement for our 6500. How to publish my design and config. This is a medium sized network. I would have loved to see somone's configs for a similar implementation.
[URL]...
I have some questions in regards to network equipment I want re-utilize for my distribution layer in one of my buildings.The choices at the moment are:
OPTION 1.) 2x WS-3550-12G's (HSRP)
OPTION 2.) 1x WS-6509 with cards:
What option would be better from a performance aspect? We want to have network, voice, and wireless data go through this distribution layer switch(es).This is exisiting equipment I already have and can not buy anything else at the moment.
To setup SG300-20 as CORE switch and SF100-48 as Distribution switch.SG300-20 will have 2 VLAN(DATA and VOICE)
-192.168.14.1/24 DATA
-172.168.0.1/24 VOICE
SF100-48 will also have 2 VLAN(DATA and VOICE)
-192.168.14.1/24 Desktop/Laptops
-172.168.0.1/24 IP phones
Problem is when I tried to assign IP to any VLAN's the switch will just hang and loose my connection the light will stop blinking it will steady and i unable to access the switch until i turn off again?
. The laptop can connect to the internet using the wifi card. However, it cannot connect to the internet when using the wired connection but it can be pinged from other machines at work. The NIC does not pick up a different IP address even after releasing and renewing the IP address through cmd. I have uninstalled and reinstalled the NIC. The NIC is working because when I set a static IP address the machine can connect to the net. Using DHCP it goes back to that same IP address. I have tried a winsock repair as well with no go, as well as taking the machine off the domain and re-joining it. Anyone see this before? Is there something I can do on my end to get a different IP address through DHCP or do I have to get a Network engineer involved? This is a machine on a corporate LAN.
View 3 Replies View RelatedI'm trying to configure MAB on a Cisco 3560G to work with FreeRADIUS.
I have been assured that my RADIUS configuration is fine and the server is functioning properly.
This is my current switch config:
Header 1
!
version 12.2
no service pad
[Code].....
Everything was working fine and I was poking around in the router settings and clicked the Clone Mac Address button to see what it did and hit Apply.
Now the internet isn't working (on the neighbor's internet) and I can't even get back on the router (192.168.1.1) I reset the router but it still isn't working.
I have an ASUS Wireless Router RT-N66R.
Edit: I got back on the router but now my wireless MAC address is the same as the LAN MAC address. I think this is what the cloning did. Is there any way to find my old MAC address?
The section is titled Special Requirement from ISP so I think I may need to use a certain MAC address but I don't remember what the old one was.
Nothing seems to be able to connect to my wireless network. It seems to have occurred after I installed a new copy of windows 7 onto my sister's desktop. A message appeared saying we have the same ip address. I've tried renewing our ip address on both desktop but it won't give us new ip address for some reason.
View 14 Replies View RelatedI'm trying to achieve framed-ip-address/static ip address for some remote access vpn clients and ip allocation from pool dynamically for remaining remote access vpn clients. I've configured my asa [URL].
I'm using local database for user authentication. Remote users can connect and always gets IP address from pool only and never gets the framed-ip I configured for those particular users.
I have recently configured secondary ip address on LAN Interface of Cisco C6509.. We have some application which needs to use broadcast traffic communication to communicate with client... Broadcast is working within subnet & also working from broadcast server to primary subnet. But not working from secondary subnet.. I have checked broadcast within secondary IP range & it's working fine... Secondary not working broadcast with primary and also with broadcast server... broadcast address is different for these subnet but both should be communicate since configured on same interface... When I went through Cisco website found that command "ip directed broadcast" which will pass broadcast to different subnet... But I'm not sure whether any other impact if I enable that command on particular Ethernet interface...
View 6 Replies View RelatedIm having a (from google-fu) seemingly unique issue with load balancing. So for background, I am running the ACE 4710 device in "on a stick" mode, so I am using NAT and all that good stuff. I am also utilizing class maps and host header matching so I can save on IP space. [code]
Basically, as soon as I add that ACL_CLASS_beta.mainsite.com class map, all I get back from the ACE is RST packets and it comes back with an L7 LB Policy Miss.
It SEEMS like it should work, but it doesnt seem to like matching on those source addresses at all.
We have a pair of N7K distribution switches connected to a pair of N7K Aggregation switches.We run vPC on both pairs of n7k's.
-n7k-d1 has two interfaces in a Port-Channel connecting to n7k-a1 & n7k-a2. (PC1)
-n7k-d2 also has two interfaces in a Port-Channel connecting to n7k-a1 & n7k-a2. (PC2)
My problem is that Spanning-Tree is blocking PC2 and all traffic from n7k-d2 is traversing the Peer-Link before reaching the Aggregation layer. Is this the best design for connecting two pairs of n7k's with vPC or if a better design would be to connect all 4 links into the same Port-Channel and vPC?
I switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies View RelatedI am having an issue where occasionally the Sidewinder starts to see my internal RFC 1918 address instead of the configured external address of my firewall. This is for peering between the two. The error they see on the Sidewinder is:So instead of seeing the external peer address he sees a 10.220.3.18 address. We are not sure what triggers this becuase normally he see's my 63.117.98.222 address.
View 5 Replies View Related
