I would like to upgrade LMS4.2 to PI1.2. According to Cisco this is a minor upgrade (requires the SAS code) and can be downloaded from the Cisco portal for free. My question: Can I still reuse the license and the B2B cisco support I use for my LMS4.2 ?
I will also upgrade WCS7.0.x to PI1.2. Will there finally be 1 server running 1 merged software, or will there be 2 servers one for WCS >> PI and one for LMS >> PI ?
We are facing issue of having minor error for SUP module details below,SUP: WS-X45-SUP6-E see the minor error coming while troubleshooting this SUP 6-E error as below,
module 3: SerialNo :
Overall diagnostic result: MINOR ERROR#
Test results: (. = Pass, F = Fail, U = Untested)
1) supervisor-bootup ---------------> U
2) linecard-online-diag ------------> F
The line card WS-X6724-SFP inserted in slot 2 is getting MINOR ERROR. I could also see TestTransceiverIntegrity: on port no 2/11 has failed.
Is this a h/w issue?
==================================================================================================
S/w model : WS-C6509-E
IOS : s72033-adventerprisek9_wan-mz.122-33.SXI3.bin
==================================================================================================
1) TestTransceiverIntegrity:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. . . . . . . . . . F . . . . . . . . . . . U .
We have a VSS environment with two Cisco 6509-Es. IOS image:s72033-ipservicesk9_wan-mz.122-33.SXI5 when I switch on or reload the Core switches(VSS), I find a Minor Error in the "Show module switch all" command.I also did a "show diagnostic result switch 1 module 5"Switch 1 Module 5: Supervisor Engine 720 10GE (Active) SerialNo : SAL1521E035
Overall Diagnostic Result for Switch 1 Module 5 : MINOR ERROR
Diagnostic level at card bootup: complete
Test results: (. = Pass, F = Fail, U = Untested)
45) TestVslLocalLoopback:
Port 1 2 3 4 5
-------------------
U U U . F
This issue temporarily relieves when reseating the X2 module, but reappears after reloading the switch.
Cant find the speeking result/cause of 4 and 1 in the example below, that are defined as enums in the MIBs normaly. Where can I access the result of "snmptranslate -M<MIB-dirs> -m ALL -Td <ps-status/test-oid>" if this is implemented in LMS overall? What are the OIDs from Cisco's ps-status/test, if the translation of MIB-enums is not implented?
Event_Description
StateNotNormalDevice IP
x.y.z.1Device Type
Switches and HubsFault Last Updated At
06-Nov-2012 16:12:49Component
[code]....
With lms 3.2 during installation we can choose what to install i.e. not install DFM or IPM.
How can we do this in the new release 4.0 of the LMS bundle. I saw no options for it during installation of the new server.
Cisco release the Cisco Prime LMS 4.1 on Aug. 2011. I download the lms4.1 from cisco and install it, but the lms4.1's evaluation license expire date is Oct. 28 2009. So my license already expired after I install the LMS4.1.
View 1 Replies View Relatedi tried to restore backup from LMS3.2.1(windows) to LMS4.2 virtual appliance. once the back up is completed, the home page takes forever to load. i opened TAC case, and the only way out seems to be configuring from scratch after importing the devices. i, imported the devices and this didn't cause any problem. But, making the configuration from scratch is something i would like to avoid if possible.
View 1 Replies View RelatedWe migrated to LMS4.2 and i created new credential set and set it as the default. However, the new cdredential set applies only to newly added devices no to the migrated devices. for example when i run device credential verfication for a migrated device, the username used my LMS is "cwuser" as opposed to the one i created with the new credential sets. how can i make this new credentila set be applicable to all devices?
View 3 Replies View RelatedIn our organisation we have multiple Nexus 5000 switches, which Cisco LMS 4.2.2 cannot get the running-config and startup-config from with the Archive Management process. When it does try to get them, I get a error as follows:
*** Device Details for SF-DERA-01 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,SCP
[Code].....
I reinstalled CiscoWorks LMS (Windows 2008 R2) updated th LMS with all availible devicepackages and imported all devices with a xml bulk import of the former installation. Now I am frustrated.... because after the reinstallation LMS has problems collecting the inventory data.The inventory collection for one local device (Cisco WS-C3560-8PC-S) starts and nevers stops.... I have to stop the ICserver to stop the inventory collection.
I have only 4 of nearly 1800 devices where it was possible to collect the inventory information.All the rest is supposed to unreacheable...Reports> Inventory>Management Status>Unreachable Devices.But if I take one of the devices which is reported to be unreacheable and do a device diagnostic (Monitor> Troubleshooting Tools> Troubleshooting Workflows) says it is reacheable...
The inventory does not appear in the "Collector Status"?
in LMS3.2.1 we have NMSRoot/log/syslog.log where syslogs are being logged actively from managed devices. i couldn't find the same in LMS4.2. I am configuring LMS4.2 from scratch and in the hope of making the trasition from old LMS3.2.1 to LMS 4.2, I am planning assigning the old LMSs IP to the new one. basically changing the IP address of LMS4.2.
View 10 Replies View RelatedI have a very special usecase with migrating devices from LMSv2.6 to v4.1 using DCR bulk import that was maintained manualy, not by discovering.The special thing is each device has its own SNMP-community and its about 1500 devices.RME discovery works fine, but I get the devices not discovered by DCR (CSDiscovery), because I need a minimal DCR discovery configration containing Seed and SNMP-settings. So I activated DCR as seed, but cant skip SNMP settings without an entry. But in this case I would need 1500 SNMP-lines that would be very unhandy. is in CSDiscovery-Settings a possibility to can leave SNMP settings untouched so it takes the credentials from the DCR, to can start DCR discovery?
View 6 Replies View RelatedI am having a strange issue deploying universalk9-150-2.SE2 to our 2960S. All the switches are stand alones.LMS gives an error when asking to upgrade the image but the fact is that the new software wents through - if I manually reload the switch everything is fine.why is RME showing an error if the new image seems to have been deployed?
View 23 Replies View RelatedWho can give me a SNMPv3 configuration template.I tried many times has been a problem
View 5 Replies View RelatedI have installed Cisco Prime Infrastructure 1.2 separately from LMS4.2. LMS4.2 is in production. I just want to run PI1.2 in parallel with LMS4.2 before migrating to PI1.2. Currently I have LifeCycle permanent license. Why don't I have the assurance lfeature set license. it is running in evaluation mode.
View 1 Replies View RelatedThis is a WS-C4510R+E with a Sup 7-E running 03.02.02.SG enterprise.
I increased SNMP timeout to 10 seconds to no avail.
I’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies View RelatedI am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
Is it possible to upgrade the CSACS-1121-UP-K9 to be a non upgrade part? We were going to upgrade from a Windows 4.x to the above Appliance (version 5.x) but there is now a reason to keep the old Windows version running therefore we cannot give the new Appliance the old ACS's licenses?!So we should have (with hindsight) bought a fresh version of the ACS 5.x rather than an upgrade.
View 1 Replies View RelatedHow to upgrade IOS XR from 4.1.2 to 4.2.0? Is their any specific requirement for same? What precaution i have to take while upgrading process?
View 1 Replies View RelatedI have a project to upgrade LMS3.2 to a new PI 1.2. my current plan is
1. build a new VM to install LMS 4.2
2. backup LMS 3.2 ( not SP1)
3. import 3.2 data to the new 4.2 machine
4.build a PI 1.2 and import 4.2 data into PI 1.2
5. run the devices side by side untill parity
As 3.2 is not SP1 can the data still be migrated into 4.2 or will I need to upgrade 3.2 to 3.2.1 ( SP1)? Is there a script to backup/restore data from 3.2 to 4.2?
I am upgrading the LMS 3.2.0 to LMS 3.2 SP1 software and also RME 4.3.0 to RME4.3.1. Do I need to add further patches to make CiscoWorks up to date.I know that LMS 4 is released but currently we are not planning to buy it.
[code]....
Is it possible to upgrade a L-ASA-SSL-10 to a L-ASA-SSL-50?Or is the only possible way to upgrade to 50 users with the upgrade licenses?L-ASA-SSL-10-25 and then L-ASA-SSL-25-50 ?
View 5 Replies View Relatedwe are running LMS 3.1 on an Win 2003 Server and now we have purchased an LMS 4.01. I installed LMS 4.01 on an new Win 2008 R2 Server. Now I want to restore an backup from the LMS 3.1 Server on the new LMS 4.01 Server. But the restore does not start and I get a message.
View 1 Replies View RelatedI have a VPN (Easy VPN) with lots of 857/857W routers. Currently we are experiencing problems FTP'ing files from the connected PC's to our central server. The problems occur especially when our main link is a bit congested and so I thought of implementing QOS on the site routers to hopefully get the FTP's through more reliably.I played with various configurations, but I can't seem to get the FTP throughput up significantly. It does not seem to work so well. It looks like I may be getting about 1kB/s more on the FTP throughput at times, but it has not made a significant difference. I am testing it by streaming a few video streams from the site PC to our server while simultaneously doing the FTP's.
View 10 Replies View Related tried to upgrade from WCS 4.2.62.11 to 6.0.196.0 however the upgrade failed as I ran out of disk space on the appliance (a converted WLSE running Redhat 5.5) I freed up some disk space but now when I try and run the upgrade I get the following error:
I've deleted all the WCS 6 files and logs that I can find but makes no difference. I only want to do this upgrade so that I can then upgrade to WCS v7 and export my existing licences to use in a new NCS install and the export licences option isn't available in versions earlier than WCS 7.
How can I upgrade from LMS 4.0 to LMS 4.1? Can I use the same license I have on LMS 4.0.And from where can i download LMS dashboard? Is it supported to work with LMS 4.x
View 6 Replies View RelatedI'm in the process of upgrading from 4.1 to 4.2.3 sequentially and I've come across a problem. Yesterday all was well in going from 4.1 to 4.2 but today after going from 4.2 to 4.2.1 I'm unable to login and get the error. This happens both with my normally RADIUS authenticated username and the admin account.
View 4 Replies View RelatedPresently we have purchased Cisco LMS3.2 package now. We need to install the same in our UCS server. My quiry is can we have option to upgrade to LMS 4.1 version with free upgradation. If so let me know how to do the same by upgrading with same LMS 3.2 License.
View 1 Replies View RelatedI'm about to upgrade an LMS 4.0 to 4.2.
As LMS 4.2 supports local upgrade from LMS 4.0.1, do I just have to install the 4.2 eval version over the existing 4.0 installation and paste the new key (which I have received through the Cisco Product upgrade tool) in te licensing menu?
know if there are any needed licenses to upgrade my CW-LMS-3.0 to CW-LMS-3.2 ? do I need to purchase any licenses ? or just downloading upgrade package from [URL] will be enough ?
View 2 Replies View Related
