Cisco VPN :: 5520 VPN Filtering And Access From Local To Remote Site
Mar 21, 2012
I have configured vpn filtering on all my l2l vpns. I have restricted access from remote to local resources only to specified ports. It works perfectly.But I want to have also full access from local to remote networks (but still preserve restricted access from remote to local). As I now VPN Filter works bi-directional with a single ACL. So is there some way to open all traffic from local to remote and still restrict remote to local traffic? ASA 5520 8.4(3)
View 4 Replies
ADVERTISEMENT
Mar 19, 2013
We have 2 5520 ASA's working in an active/standby function at our central site. The remote agencies have control of their ASA's or other devices able to create VPN tunnels back to the central site. When a new remote agency wants to connect to our central site we assign them a network range that is routable on the central sites network.We ask that the remote agency NAT into the addresses we provided them.This way we are able to route back to them. We assign the interesting traffic and then they we start communicating by way of the tunnel.
Since the central site can't control the traffic coming in on the site to site tunnel other than just defining the interesting traffic AND we aren't able to control the NAT on the remote end how can I put an access list on the central site ASA to allow only certain ports and IP's by way of access list? Ultimately, I'm trying to limit traffic on the central site coming inbound to only allow traffic I want. I tried applying a group policy to the lan2lan site to site tunnel, but it failed for some reason. It actually prevented all traffic. Can I apply a group policy to a site-to-site tunnel?
I'm struggling here a bit as I don't have control of the remote end. They can NAT whatever they want to an address in the range we assigned them. The tunnels interesting traffic is set to full ip to the central site's destination. The interesting traffic on the central site is set the same. However, on the central side...I want to limit that traffic to only certain ports by way of an acl. If it is possible to assign a site-to-site tunnel a group policy and filtering is done in that method, can
View 3 Replies
View Related
Jun 17, 2012
We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies
View Related
Jul 21, 2011
I setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access.
Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
View 6 Replies
View Related
Oct 29, 2011
We have a site-site and remote vpn configured in same interface in ASA 5520 ( software version 8.3 ). When Remote vpn users try to connect to computers located on the distant end of site-site VPN, their request failed. I tried No-Nat between remote vpn private IP to the remote site private IP, also stated the same in Split tunneling. I cant find even the tracert, ping also timed out.
View 7 Replies
View Related
May 18, 2012
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies
View Related
Aug 18, 2011
I have a Cisco 2911 router configured with a couple of VPN tunnels . The issue that I am having is that I cannot access the servers (WEB,EMIL) thru the tunnel . After looking around found out that adding a route-map to my static NAT rule will fix the issue . Once I do that I am able to access the serves thru the VPN but my local machines lose internet access .So I have to delete the access list The issue seems to be with the Access list 110 permit ip [code]
View 5 Replies
View Related
Jan 14, 2013
We have a 5508 controller in main site.Which has two ports connected to local network.Management VLAN 500 is untagged and mapped to Port 1.All other interfaces are including 501 to 507 are mapped to Port 2.We have a SSID that is mapped to VLAN 501 interface , which successfully can be joined in main site.We connect an AP to remote site ;We have a remote site VLAN 115 which can be reached from main site.We connect an AP to access vlan 115 port on the remote site , we had described option 43 , so AP can successfully finds controller in local mode.
AP gets ip from VLAN 115 , can setup connection / ping controller successfully.There is a wide area connection between remote and main site.No trunk setup , the whole remote site is vlan 115.However when the client is trying to connect the test SSID , client cant get connected nor get ip address.Local switching is disabled.For this setup , client comes to AP as a requested , AP tunnels traffic to controller from vlan 500 , controller lets the client get into wired platform from VLAN 501.
View 25 Replies
View Related
Jul 15, 2012
we have two ASA 5510s one in 8.4(4) and one in 8.2(5) in a site-to-site VPN setup. All internal traffic is working smoothly.Site/Subnet A: 192.160.0.0 - local (8.4(4)) Site/Subnet B: 192.260.0.0 - remote (8.2(5)) VPN Users: 192.160.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible.
Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise.There are also some weird NAT rules that I am not happy with that were created after I upgraded Site A ASA to 8.4
Site A internal: 192.160.x.x External: 55.55.555.201(main)/202(mail)
Site B (over site-to-site) is 192.260.x.x External: 66.66.666.54(all)
I pretty much just have the basic NAT rules for VPN, Email, Internet and the site-to-site.What do I need to add for the VPN to be able to access the site-to-site network?
Here is my NAT config:
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static VPN_Network VPN_Network no-proxy-arp route-lookup
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static DOMAIN_REMOTE DOMAIN_REMOTE no-proxy-arp route-lookup
!
object network DMZ_Network
nat (DMZ,Outside) dynamic interface
object network DOMAIN_LOCAL
[code]....
View 3 Replies
View Related
Mar 9, 2011
I am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).
View 6 Replies
View Related
Feb 14, 2011
I have a cisco ASA 5510 at the branch here. It terminates about 8 vpn tunnels and also it supports remote access clients. I just have a quick question. Can my remote sub-net group access the other remote access site-site VPN subnet group. If yes then how should i configure it.
View 6 Replies
View Related
Jan 9, 2012
I am having an issue with establishing L2L VPN with remote site. My side is cisco asa 5520 and other side is check point UTM-- tunnel is not up.just wnated to confirm on my sidde if the configuration is OK.al the parameters using are correct for both side. any issue with below conf ? default route is pointing to my next GW address is there additiona default is required for VPN ? to reach the remote LAN somthing like pointing to remote peer address.to give a brief idea front end device is router as GW wher in internet is terminated and other wan connections ASA is behind ther GW rtr and outside int of asa and lan interface of GW rtr is having public ip. LAN switch is connected to ASA
access-list insideinterface_nat0_outbound extended permit ip 192.168.36.0 255.255.255.0 10.34.12.0 255.255.254.0
access-list outsideinterface_cryptomap_40 extended permit ip 192.168.36.0 255.255.255.0 10.34.12.0 255.255.254.0
nat (insideinterface) 0 access-list insideinterface_nat0_outbound
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
[code]....
View 9 Replies
View Related
Jan 13, 2012
I have a remote office that currently connects back to a Central data center via Site to Site VPN. I am bringing up a 2nd internet connection as a fall back in the Remote Office. How do I configure the Site to Site VPN to work correctly so that if the primary internet connection goes down, the site fails over to the secondary? On Remote the internet connections are from different providers so they have completely different blocks of public IPs.
Central
ASA 5520 8.0(4)
Gig 0/0 Public IP
Remote
ASA 5520 8.4(1)
Gig 0/0 Public IP
Gig 0/3 Public IP (2nd internet)
View 1 Replies
View Related
Sep 8, 2012
I have a site-to-site VPN configured between a 5520 at our data center, and a 1700 at a client's site for site-to-site connectivity. What I've noticed is, is that the VPN can only initiate from my Data Center, never from the client router. I can telnet into the router and start a telnet session sourced from the "inside" interface and it fails, yet I can see the NAT translations get created in the state table that should match the crypto-map. However, if I ping a host on the inside of the remote LAN from my workstation (behind the 5520) to bring the tunnel up, and run the exact same command on the client router once the tunnel is up, it works. Right now I have a continuous ping running from my workstation to keep the tunnel up, but obviously that's not the best solution
I had to modify this config to NAT the LAN addresses at the client to a non-overlapping subnet, so anything coming from 128.1.0.0/16 should be NAT'd to 192.168.105.[50-200]/24. I've also got two static NATs for inbound access from the data center and those seem to work fine.
Current configuration : 2787 bytes
!
! No configuration change since last restart
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]...
View 2 Replies
View Related
Jun 28, 2012
I am attempting to configure Radius authentication accross a site-to-site VPN for my ASA 5510-01 for remote access.
ASA5510-1 currently has a live site to site to ASA5510-2.
ASA 5510-1 - 10.192.0.253
ASA 5510-2 - 172.16.102.1
DC - 172.16.102.10
ASA5510-01 can ping the DC and vica versa but is unable to authticate when i perform a test. ASA5510-01 can authenticate to a DC on it;s own LAN but not on the remote LAN that DC sits on.
I have double checked the 'Server Secret Key' and ports as well as various users which all work locallly. ASA5510-02 authenticates to DC with no problems.
View 3 Replies
View Related
Mar 15, 2012
Have asa 5520 ver 8.0(4) I have vpn client access created and working I have l2l vpn created and working with another set of asa The issue at hand VPN client from internet connects and authenticates, this client can access Site A's networks with no problems. However vpn client on Site A ASA can not access Networks through l2l tunnel located at Site B.
View 2 Replies
View Related
Jun 3, 2012
I'm attempting to configure an for both site-to-site and remote access VPNs. The site-to-site is working fine, however when I connect using the Cisco client, after initial connection and password prompt I get a "not connected" status. The log states that a policy map match could not be found. I have successfully set the unit up for remote access with no site-to-site and ran into another host of issues when adding the site-to-site to the working remote access config, so I started over setting up site-to-site first. I've attempted this through ADSM (hate it) - the current configuration is via CLI. I'm certain I'm just missing a piece or two.
View 2 Replies
View Related
Aug 8, 2011
can I configure Site-To-Site VPN and Remote Access VPN at the same time in one ASA 5510?
View 8 Replies
View Related
May 29, 2012
Is it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC
View 1 Replies
View Related
Apr 7, 2013
I have a site to site vpn connection between ASA 5510 and PIX 515 which is working fine. There is no problem for hosts on any side of the tunnel to access a cross. However the local ip (192.168.20.1) on the client interface of my PIX is not allowed to access hosts on the other side of the tunnel. [code]
View 2 Replies
View Related
Jun 13, 2012
The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
View 1 Replies
View Related
Oct 11, 2011
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies
View Related
Oct 18, 2011
i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration
ASA Version 8.2(1)
!
!
interface Vlan1
[Code].....
View 13 Replies
View Related
May 22, 2013
We have 3 offices, each with an ASA 5505 as the router/firewall, connected to the cable modem
(NC office) <----IPSEC----->(PA office) <----IPSEC-----> (CT office)
Internally we have a full mesh VPN, so all offices can talk to each other directly.I have people at home, using remote access VPN into the PA office, and I need them to be able to connect to the other two offices from there.I was able to get it to work to the CT office, but I can't get it to work for the NC office. (What I mean is, users can remote access VPN into the PA office, and access resources in the PA and CT offices, but they can't get to the NC office).
Result of the command: "show run"
: Saved:ASA Version 8.2(5) !hostname WayneASA
names!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address 70.91.18.205 255.255.255.252 !ftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns domain-lookup insidedns domain-lookup outsidedns server-group DefaultDNSname-server 75.75.75.75name-server 75.75.76.76domain-name 3gtms.comsame-security-traffic permit intra-interfaceobject-group protocol TCPUDPprotocol-object udpprotocol-object tcpaccess-list inside_access_in extended permit ip any any access-list IPSec_Access extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 access-list IPSec_Access extended
[code].....
View 15 Replies
View Related
Dec 12, 2012
I have 2 site here:
site A
Cisco 891
external IP: 195.xxx.yyy.zzz
VPN Gateway for Remote users
[Code]....
View 1 Replies
View Related
May 5, 2011
I have a 3845 router (12.4(13r)T10) with ZBF. On my LAN there is a user who need to access a remote IPSEC VPN server. He is able to get the tunnel but afterwards he cannot connect to any service in the remote LAN. As I'm using zbf I think that I should inspect traffic from my LAN zone to EXT zone, There is a document that describe a solution to this? What IP adressess should I use?
View 2 Replies
View Related
Oct 3, 2011
I have a 3845 router (12.4(13r)T10) with ZBF. On my LAN there is a user who need to access a remote IPSEC VPN server. He is able to get the tunnel but afterwards he cannot connect to any service in the remote LAN. As I'm using zbf I think that I should inspect traffic from my LAN zone to EXT zone
View 3 Replies
View Related
Mar 6, 2011
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies
View Related
Oct 26, 2011
Users are connecting to Site A (PIX 515e) via Cisco VPN client and can access servers/resources within that site no problem. They cannot access anything within Site B (ASA 5505) however. Devices communicating between Site A and Site B have no issues (have site to site VPN configured). I'm assuming that I'm missing something in configuration - or is it not possible for VPN clients connected to the PIX firewall and access data on the other network?
View 1 Replies
View Related
Dec 12, 2011
I have 2 sites :
site A :
ASA 5510
VPN gateway for remote users
LAN 192.168.192.0/22
site B :
ASA 5505
LAN 192.168.208.0/22
Both sites are connected through a site to site VPN.Remote clients (AnyConnect/VPN client) can connect to Site A LAN and see machines on LAN A but cannot see Site B LAN.
Here is a part of my configuration :
On Site A (ASA 5510)
--------------------------------
name 192.168.192.0 SiteA_Internal_Network
name 192.168.208.0 SiteB_Internal_Network
name 192.168.133.0 VPNPool_AnyConnect
name 192.168.133.32 VPNPool_VpnClient
[code]....
View 9 Replies
View Related
Jan 12, 2012
I would like to create a additional user vpn on a 55010 where the user authenticates with the firewall and not the radius server.This user should NOT be able to log on to the firewall, but only be able to authenticates with the vpn client.I'm correct that the command "username abc123 password abc234 privilege 0" ?Also for this remote vpn how to I make sure the user only authencates with this password?
View 3 Replies
View Related
Oct 4, 2012
I am configuring remote access vpn on ASA5505.Everything is working fine so far, except when the client got connected, it still used the local DNS server provided by the ISP. How do I force the client to use the DNS server configured on ASA?
View 7 Replies
View Related
May 29, 2011
In my Cisco PIX-515E Version 6.3(5), I have a IPSec VPN tunnel and also to the same firewall home users connect through VPN client. I am unable to find a solution that allows my home users to connect to office network and again access the remote network through the IPSec tunnel.
View 1 Replies
View Related
