Cisco VPN :: 5520 / IPSec VPN Won't Initiate From Remote Site
Sep 8, 2012
I have a site-to-site VPN configured between a 5520 at our data center, and a 1700 at a client's site for site-to-site connectivity. What I've noticed is, is that the VPN can only initiate from my Data Center, never from the client router. I can telnet into the router and start a telnet session sourced from the "inside" interface and it fails, yet I can see the NAT translations get created in the state table that should match the crypto-map. However, if I ping a host on the inside of the remote LAN from my workstation (behind the 5520) to bring the tunnel up, and run the exact same command on the client router once the tunnel is up, it works. Right now I have a continuous ping running from my workstation to keep the tunnel up, but obviously that's not the best solution
I had to modify this config to NAT the LAN addresses at the client to a non-overlapping subnet, so anything coming from 128.1.0.0/16 should be NAT'd to 192.168.105.[50-200]/24. I've also got two static NATs for inbound access from the data center and those seem to work fine.
Current configuration : 2787 bytes
!
! No configuration change since last restart
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration... Current configuration : 5425 bytes ! ! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01 ! version 12.4 no service pad
We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
We have configured a site to site tunnel from our ASA to another organizations Cisco 3030. It appears to have just one way initiation. We can do a ping to a device on the remote site and it will ping just fine. however, when the tunnel needs to be initiated from the remote site, it will not work until we have initiated the tunnel and then everything works.
I continue to see Error processing payload: Payload ID: 1 errors on the ASDM logs.It appears that all the configuration is in place because we can in fact establish the IPSec tunnel unidirectional. And once established, traffic can flow bidirectional.
I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
I recently faced an issue at work. Clients want to make ipsec site-to-site vpn redundant. I have 2-asa-5520 working in a stack. Is it possible to configure site-to-site vpn in a redundant mode, like first peer ip address is x.x.x.x and secondary is y.y.y.y (backup) ?
We have a site-site and remote vpn configured in same interface in ASA 5520 ( software version 8.3 ). When Remote vpn users try to connect to computers located on the distant end of site-site VPN, their request failed. I tried No-Nat between remote vpn private IP to the remote site private IP, also stated the same in Split tunneling. I cant find even the tracert, ping also timed out.
We already have IPSEC VPN connectivity established between sites but would like to introduce some resilience/redundancy at a remote site.
Site A has an ASA with one internet circuit.
Site B has a Cisco 2911 with one internet circuit and we have established site-to-site IPSEC VPN connectivity between the 2911 and the ASA.
Prior to getting the new internet circuit, Site B had a Cisco 877 with an ADSL line which are still available but aren’t currently in use.
The internet circuit at Site B has dropped a few times recently so we would like to make use of the ADSL circuit (and potentially the 877 router too) as a backup.
We thought about running HSRP between the 877 and 2911 routers at Site B and, in the event of a failure of the router or internet circuit, traffic would failover to the 877 and ADSL.
However, how would Site A detect the failure? Can we simply rely on Dead Peer Detection and list the public IP address of the internet circuit at Site B first with the public IP address used on the ADSL line second in the list on the ASA? What would happen in a failover scenario and, just as important, when service was restored – I’m not sure DPD would handle that aspect correctly?
I’ve read briefly elsewhere that GRE might be best to use in this scenario – but I can’t use GRE on the ASA. I have an L3 switch behind the ASA which I may be able to make use of? But I don’t want to disrupt the existing IPSEC VPN connectivity already established between the ASA and the 2911. Can I keep IPSEC between the ASA and 2911 but then run GRE between the L3 switch and the 2911? If so, how would this best be achieved? And how could I also introduce the 877 and ADSL line into things to achieve the neccessary redundancy?
In my Cisco PIX-515E Version 6.3(5), I have a IPSec VPN tunnel and also to the same firewall home users connect through VPN client. I am unable to find a solution that allows my home users to connect to office network and again access the remote network through the IPSec tunnel.
Is there any documents that I can use to design an IPSEC remote access solution using 2 data centers . One data center is primary and other one is secondary. The VPN is terminated in ASA 5520. End users using cisco client.
We have dns server(only Internal IP) inside our network, right now we have configured Remote Access VPN using Public IP and we connect it using the same Public IP. I need to use FQDN instead using Public IP. What is the configuration for this.
we wish to implement IPSec remote access vpn with the condition that employees should be able connect to this vpn only from company issued laptops and not from any other computers. I assume using client side certs is one of the ways to do it but I couldn't find any doc that was really useful. Cisco's documentation seems quite obscure. We are on 8.1 (5520)
I am having an issue with establishing L2L VPN with remote site. My side is cisco asa 5520 and other side is check point UTM-- tunnel is not up.just wnated to confirm on my sidde if the configuration is OK.al the parameters using are correct for both side. any issue with below conf ? default route is pointing to my next GW address is there additiona default is required for VPN ? to reach the remote LAN somthing like pointing to remote peer address.to give a brief idea front end device is router as GW wher in internet is terminated and other wan connections ASA is behind ther GW rtr and outside int of asa and lan interface of GW rtr is having public ip. LAN switch is connected to ASA
I have a remote office that currently connects back to a Central data center via Site to Site VPN. I am bringing up a 2nd internet connection as a fall back in the Remote Office. How do I configure the Site to Site VPN to work correctly so that if the primary internet connection goes down, the site fails over to the secondary? On Remote the internet connections are from different providers so they have completely different blocks of public IPs.
Central ASA 5520 8.0(4) Gig 0/0 Public IP
Remote ASA 5520 8.4(1) Gig 0/0 Public IP Gig 0/3 Public IP (2nd internet)
We have 2 5520 ASA's working in an active/standby function at our central site. The remote agencies have control of their ASA's or other devices able to create VPN tunnels back to the central site. When a new remote agency wants to connect to our central site we assign them a network range that is routable on the central sites network.We ask that the remote agency NAT into the addresses we provided them.This way we are able to route back to them. We assign the interesting traffic and then they we start communicating by way of the tunnel.
Since the central site can't control the traffic coming in on the site to site tunnel other than just defining the interesting traffic AND we aren't able to control the NAT on the remote end how can I put an access list on the central site ASA to allow only certain ports and IP's by way of access list? Ultimately, I'm trying to limit traffic on the central site coming inbound to only allow traffic I want. I tried applying a group policy to the lan2lan site to site tunnel, but it failed for some reason. It actually prevented all traffic. Can I apply a group policy to a site-to-site tunnel?
I'm struggling here a bit as I don't have control of the remote end. They can NAT whatever they want to an address in the range we assigned them. The tunnels interesting traffic is set to full ip to the central site's destination. The interesting traffic on the central site is set the same. However, on the central side...I want to limit that traffic to only certain ports by way of an acl. If it is possible to assign a site-to-site tunnel a group policy and filtering is done in that method, can
I have configured vpn filtering on all my l2l vpns. I have restricted access from remote to local resources only to specified ports. It works perfectly.But I want to have also full access from local to remote networks (but still preserve restricted access from remote to local). As I now VPN Filter works bi-directional with a single ACL. So is there some way to open all traffic from local to remote and still restrict remote to local traffic? ASA 5520 8.4(3)
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
I have an ASA 5525 and need to configure site to site ipsec vpn to 3 peers. I currently have an existing /28 public address from my ISP that is used by other services.Is there a way to use this existing ip range to configure IPSEC tunnels to 3 peers ?
With à customer we have à site to site VPN connection. In this tunnel there is one subnet routed with a 3des-sha encryption / hash. Now the want to add a new subnet in this tunnel, but with a AES-128 / MD5 encryption / hash. Is it correct if we make a new crypto map with a higher seq. number?
im drawing a blank trying to setup a site to site connection with a 5505 ASA using ipsec and isakmp.i have the pre shared key as well as the external address of the other end of the tunnel but do not remember what the commands are to setup the crypto map and isakmp.
We have a scenario where the Cisco ASA 5505 will be one end of a site-to-site VPN. The same ASA 5505 also allows Client VPN connection. The question is around IP pooling. If I assign a pool of IP's (192.168.1.20 - 192.168.1.30) for Client VPN connections - do I need to be sure that those same IP's are not used on the other side of site-to-site VPN ?
There could be PC's/Servers running 192.168.1.0/24 on the other side of site-to-site VPN. Would this cause an address conflict ?
I have configured Ipsec vpn tunnel beetween two routers (from site A to site B) over untrusted internet connection by cisco 3825 routers and i can successfully access both of this routers. But now i need to access internet on site B router sitting on site A router. So that if i run traceroute from A site machine then the gateway by which internet passing through shows the ip of site B.
The Architecture of our both site routers :
Site A 10.1.11.0-----Router A 172.18.12.1-----VPN tunnel----Router B 172.18.12.2-----Site B 10.4.11.0
/////Create IKE policy crypto isakmp policy 1 encr aes authentication pre-share group 2 [Code] .....
How can I NAT the same set of four hosts and give them access to two different networks across an IPSEC site-to-site VPN tunnel? I'm using an ASA5520 running 8.04.
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
All these remote networks are at the Main Site Clavister Firewall.
I have a situation where the site-to-site tunnel is already established using PPTP IPSec VPN with non Cisco Gateways terminating the link on each end. These non Cisco Gateways do not support L2TP tunneling, and there is no plan to change them.Beyond the Gateways on both ends, we have a Cisco 4500 series switch. We need to forward the 802.1q tagged VLANs between the two sites. Is it possible to use 802.1Q tunneling in this case, going via a PPTP tunnel ?
Cisco's setup uses dot1q-tunnel over a L2protocol-tunnel to preserve the original client VLAN tagging, so does this mean that the only option we have is to setup a L2TP tunnel at the Cisco device endpoints, and have that tunnel go through the existing PPTP tunnel (established between the 2 non Cisco VPN Gateways) ?
My requirment is Clients from site A should access the Internet from site B (B will be providing internet to site A), So I have configured Ipsec vpn tunnel beetween two routers (from site A to site B) over untrusted internet connection by cisco 3825 routers and i can successfully access both of this routers.I have configured a client machine in site A and configured gateway of this client is 10.1.11.254 but dont have internet there.
I have a Cisco 2911 router and a Cisco RV 120W router and i would like to establish a VPN tunnel between theese two. I have defined the settings on the Cisco RV 120W router and i just want the Cisco 2911 to follow those. setting up a connection with Cisco IOS.
