I have a site to site vpn connection between ASA 5510 and PIX 515 which is working fine. There is no problem for hosts on any side of the tunnel to access a cross. However the local ip (192.168.20.1) on the client interface of my PIX is not allowed to access hosts on the other side of the tunnel. [code]
View 2 Replies
I have a Cisco 2911 router configured with a couple of VPN tunnels . The issue that I am having is that I cannot access the servers (WEB,EMIL) thru the tunnel . After looking around found out that adding a route-map to my static NAT rule will fix the issue . Once I do that I am able to access the serves thru the VPN but my local machines lose internet access .So I have to delete the access list The issue seems to be with the Access list 110 permit ip [code]
View 5 Replies View RelatedI have configured vpn filtering on all my l2l vpns. I have restricted access from remote to local resources only to specified ports. It works perfectly.But I want to have also full access from local to remote networks (but still preserve restricted access from remote to local). As I now VPN Filter works bi-directional with a single ACL. So is there some way to open all traffic from local to remote and still restrict remote to local traffic? ASA 5520 8.4(3)
View 4 Replies View RelatedI have, what I believe to be, a simple issue - I must be missing something. Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209). There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off. The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue. Basically, the VPN is up and running but PC 10.51.253.210 cannot get out
ASA Version 7.2(4)
!
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
[Code]...
I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.
I setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access.
Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View RelatedI am trying to block access to facebook and twitter on my router, to a certain range of ips, 192.168.1.8 - 254. I have been digging around and trying stuff but all I do seems to restrict everyone access to the internet.
View 5 Replies View RelatedWhen i connect VPN in server site then I can't use my Local Internet connection?
View 1 Replies View RelatedI configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
Our Headquarter (asa 5510) is running a site to site vpn connection with a Branch office (router 2811). All remote users are accesing the internet through the VPN and also accesing headquarter file servers.I want to know if there is a way for some remote users to be able to use the vpn for accesing the file servers but to access the internet through the branch office. The rest of the remote users will be still accessing the internet through VPN.
View 2 Replies View RelatedI've setup a site to site vpn on an ASA 5510 using ASDM (as I have many times before) and the tunnel appears to be up but I am not able to pass traffic. When I run the packet tracer from my inside network to the remote destination network, it shows that it is blocked by the implicit deny ip any any rule on my inside incoming access list.
View 5 Replies View Relatedwe have two ASA 5510s one in 8.4(4) and one in 8.2(5) in a site-to-site VPN setup. All internal traffic is working smoothly.Site/Subnet A: 192.160.0.0 - local (8.4(4)) Site/Subnet B: 192.260.0.0 - remote (8.2(5)) VPN Users: 192.160.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible.
Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise.There are also some weird NAT rules that I am not happy with that were created after I upgraded Site A ASA to 8.4
Site A internal: 192.160.x.x External: 55.55.555.201(main)/202(mail)
Site B (over site-to-site) is 192.260.x.x External: 66.66.666.54(all)
I pretty much just have the basic NAT rules for VPN, Email, Internet and the site-to-site.What do I need to add for the VPN to be able to access the site-to-site network?
Here is my NAT config:
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static VPN_Network VPN_Network no-proxy-arp route-lookup
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static DOMAIN_REMOTE DOMAIN_REMOTE no-proxy-arp route-lookup
!
object network DMZ_Network
nat (DMZ,Outside) dynamic interface
object network DOMAIN_LOCAL
[code]....
ASA = 8.2(1)
ASDM = 6.2(1)
Recently I used the wizard to create an IPsec site-to-site connection, which went very smoothly; however, I now noticed that when I connect via Anyconnect 2.5.0217 I cannot get to local and subnatted resources on the network.
I rolled back to saved config file, which was taken before the site-to-site vpn was created, but that did not work as well.What should I check to see why I can no longer get to different subnets after the site-to-site vpn connection.
I am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).
We have a client that has a Cisco 1801W Firewall that is setup as a site to site VPN terminating to a Cisco ASA 5505. The tunnel is up and established, I can ping from both sides of the tunnel.
The problem is the clients behind the Cisco ASA (192.168.2.x) cannot reach certain ports behind the Router (192.168.1.x). The main thing we're trying to do is browse via UNC path (ex: \192.168.1.120 from a 192.168.2.x machine).
I got 3389 working after I changed the - ip nat inside source static tcp 192.168.1.120 3389 y.y.x.x 3389 route-map DM_RMAP_1 extendable Modified the command to include the public IP instead of interface FastEthernet0
I believe it has something to do with the way NAT and route-maps are setup currently but I'm not familar enough with them to make the changes. I worked with Cisco to ensure the VPN tunnel was fine and it's something security related on the Router.
Here is the configuration (removed a few lines not necessary. y.y.x.x = WAN IP of Router x.x.y.y = WAN IP of ASA).
Building configuration...
Current configuration : 23648 bytes
!
version 12.4
no service pad
[Code].....
I have a ASA 5510 that has multiple site to site VPNs. I need to create an additiona site to site VPN but only allow 1 host to access and traverse the tunnel. The network is on a 192.168.5.x but the host that will need to access this tunnel needs to be on a 172.16.33.x network. I dont want any other traffic allowed to access or traverse the VPN tunnel for this host. How can I set this up?
View 33 Replies View RelatedHow can I NAT the same set of four hosts and give them access to two different networks across an IPSEC site-to-site VPN tunnel? I'm using an ASA5520 running 8.04.
I have four hosts say: 10.240.1.1-10.240.1.4
They need access to two different networks:
205.100.150.0
140.175.200.0
I woud like to NAT them as something like:
7.5.210.1
7.5.210.2
7.5.210.3
7.5.210.4
I have a cisco ASA 5510 at the branch here. It terminates about 8 vpn tunnels and also it supports remote access clients. I just have a quick question. Can my remote sub-net group access the other remote access site-site VPN subnet group. If yes then how should i configure it.
View 6 Replies View RelatedCan I use a single Public IP address for both Internet access and site to site vpn access?If not, can I configure the RV220W as a bridge and still use it via another gateway configured for vpn passthrough as a VPN appliance/server on the LAN?
View 3 Replies View RelatedI am attempting to configure Radius authentication accross a site-to-site VPN for my ASA 5510-01 for remote access.
ASA5510-1 currently has a live site to site to ASA5510-2.
ASA 5510-1 - 10.192.0.253
ASA 5510-2 - 172.16.102.1
DC - 172.16.102.10
ASA5510-01 can ping the DC and vica versa but is unable to authticate when i perform a test. ASA5510-01 can authenticate to a DC on it;s own LAN but not on the remote LAN that DC sits on.
I have double checked the 'Server Secret Key' and ports as well as various users which all work locallly. ASA5510-02 authenticates to DC with no problems.
Have asa 5520 ver 8.0(4) I have vpn client access created and working I have l2l vpn created and working with another set of asa The issue at hand VPN client from internet connects and authenticates, this client can access Site A's networks with no problems. However vpn client on Site A ASA can not access Networks through l2l tunnel located at Site B.
View 2 Replies View Relatedwe set up a site-to-site-vpn between a 5505 and a 5510 (both asa8.3.1). We configured both sides using the VPN-Wizard in the ASDM. When we try to ping from the network behind the 5505 (192.168.45.0/24) to any host behind the 5510 (192.168.0.0/24) the tunnel gets established but the ping doesn't get trough. After that we tried to connect via RDP to any host behind the 5510 and it worked well (same with ssh, telnet,vnc etc.). Now we want to map a network-share on a 2008-Server behind the 5510 but it's not working. In the ASDM-Log I see some "denied by inside-access in"-messages for the ports 139 and 445. Isn't it right that the whole traffic in the vpn-tunnel bypasses the acl? Even if we open both ports we can't connect to the network-share?
View 1 Replies View RelatedI'm attempting to configure an for both site-to-site and remote access VPNs. The site-to-site is working fine, however when I connect using the Cisco client, after initial connection and password prompt I get a "not connected" status. The log states that a policy map match could not be found. I have successfully set the unit up for remote access with no site-to-site and ran into another host of issues when adding the site-to-site to the working remote access config, so I started over setting up site-to-site first. I've attempted this through ADSM (hate it) - the current configuration is via CLI. I'm certain I'm just missing a piece or two.
View 2 Replies View RelatedI am considering to buy two RV180Ws and place them on two separate locations. But before buying I would like to make sure that the units meets my requirements. Lets call the locations A and B. I would like to connect location A with full network access to location B. But at the same time I would like to have that location B also gets full access to the network at location A.Besides this I would like to be able to connect to one of the networks from remote with my laptop.Preferably all connections should be made using IPSEC and not PPTP.I would like to know if it is possible to make such a configuration, and eventually if there is a smarter way to do e.g. only letting clients connect to location A or B and granting them access to all ressources at both location A and B from there.
View 1 Replies View RelatedI am trying to configure my network so that VPN traffic is only routed to a single physical port on the RV180 or to a certain subset of devices on a network.
I have a site-to-site vpn setup in a home office and am connecting to the corporate network. The user has a couple of devices running on the home network that need access to the corporate network.
We are hoping to leave his PC accessible to his home network as well as the corporate network, but restrict other devices from accessing the vpn.
I beleive I could do it by playing with the subnet but I can't get my head around it.
We have a Cisco ASA 5510 at our main office that makes connection with a 5505 at our other office using site to site VPN. (works)
Now for the question,
we want to access our other office from the main office but we wont want them to have access to our servers etc. so basically we want to control them but they shouldn't have the rights to control us.
Is this possible with a site to site VPN? and how to do it.
Our HQ office has an ASA 5510 with full access to internal and external IP's. We have a small group of remote users that are working from a shared office suite and they only have Internet access by way of internal default gateway. Using a VPN client is not desirable due to many other devices requiring access to HQ. Is there a way to create a site-to-site VPN from this remote office space back to HQ (ASA 5510) if they have no access to the public IP address on their end?
View 2 Replies View RelatedI'm just new with ASA. I'm just self-studying on it. I was tasked to have an ACL that will allow inside hosts to access a specific network. Is there a way on how to know all the inside hosts on the behind ASA so that I can do a "object-group network" on those inside hosts which I think it will look neat.
View 1 Replies View RelatedI have configured the ASA in a very similar manner to how the PIX was set up but I'm having trouble with some hosts on the inside accessing the Internet. Any inside hosts which use DHCP work fine. Any inside hosts with a static IP (and configured on the ASA with a "static" rule) cannot access the Internet. For example, in the config below the server daviker-dialler cannot access the Internet. I've spent a few days working on this now and have started from scratch several times but I'm not getting anywhere. Apologies for all the X's everywhere, didn't like to post anything sensitive on the Internet.
View 2 Replies View RelatedI am using a three interface ASA config (Internet, DMZ, Inside). The DMZ and Inside networks are both RFC 1918 space however it is against our corporate policy to allow our DMZ IP space to be internally routable, therefore we must target routable IP's which NAT to the DMZ hosts . In my DMZ network there are two devices - a Web Server and a 802.11 Access Point.
The Web Server is hosting our corporate web site. When the clients accessing the internet via the Access Point try to access our corporate web site they are not able to. A DNS lookup of the A record 'www' returns the public IP address, which when targeted translates to the real RFC 1918 IP of the web server.
Is there a way to use destination NAT or another clever config so when a host targets a public IP which is being translated on a different interface right back into the same interface it originated from it would allow the traffic?
I have recently upgraded from a Cisco Pix 515E to a Cisco ASA 5512-X.
I am obviously having trouble considering the changes implemented in 8.2. I have set up the wan and lans appropriately, as well as the VPN's. Everything is working at my location, and the VPN's are established as well.
I would like to be able to have full access in between all three VPN's and my location considering our web, email, DVR, and database servers are here.
I can't seem to ping or access my off site routers GUI pages the way I can with the PIX.
When I establish the mirrored rules on the firewall, I am able to do these things, but I lose internet at my current location.
I have problem with accessing servers through site-to-site vpn from ASA which makes this site-to-site vpn and has enablerd Clientless VPN.Reason why I need it / What I need to do:ASA 5510 has enabled Clientless VPN and on this portal is allowed users to go to URL of internal servers through bookmars. We are using it when somebody could not access IPSec VPN or is in internet cafe. So this user logs into clientless vpn and click on bookmark to access mail server for exmaple. But there is problem, asa cannot access this server through site-to-site VPN.
Network:Here is quick design of my network.I don't have problem access server in VLAN 159 from VLAN 10 or 100. But I need to be able access servers in Vlan 159 from ASA 5510 which has IP address 192.168.1.4.I have this subnet which ASA belongs in BEFORE-NAT object in same place as VLAN 10, 100 are and in Site-to-Site vpn profile.
