Cisco Wireless :: WLC5508 - Requires To Setup A Dynamic Interface On A Network?
Aug 10, 2012
Having setup several WLC4402's in the past, I am posed with a new implementation that I have never tried before. I will be setting up a new 5508 that will ONLY be used for remote access-points in H-REAP mode. It is going into a data center and there will be no local LWAPP's.Is it still required to setup a dynamic interface on a network that will essentially only have the controller IP? Or can I serve all the AP's out of the single, untagged management interface (which I believe is also the old ap-manager interface now?)
View 2 Replies
ADVERTISEMENT
Dec 14, 2011
I have one ASA 5510, a primary ISP (cable, the single public IP lives on the ASA), and a backup ISP (ADSL, separate router that hosts its single public IP). I use IP tracking to detect link down on the primary. When I pull the plug on the cable modem and go to "Route monitoring", I can see the ASA's default route is now the backup ISP default route.That conforms with [URL] Pings to 8.8.8.8 fail however, and when I do a packet trace the ASA complains about the dynamic nat rule that still points to the primary ISP's interface.Only when I change the existing dynamic NAT rule (on my inside interface) to use the backup ISP's pool (which is a single 192.168.x.y address) , does 8.8.8.8 reply to my pings. So it kinda works but it's not full auto . I can't add a second dynamic nat rule on the same inside interface, nor can I select 2 IP pools in a single dynamic nat rule.
View 4 Replies
View Related
Apr 17, 2013
Is it possible to setup DHCP on the WLC5508? If i have 2 or 3 VLAN with different Scope and IP range, how can i do?
View 1 Replies
View Related
Apr 6, 2010
I just installed my new Cisco E3000 and configured it over the HTTP interface, as I have on previous routers. I am unable to find any setting for the "Guest" wireless network (outbound internet only), or the Parental controls. Both of these are features of interest, and they're simply not listed in any of the web-based settings.
Puzzled, I did a Factory Reset and configured it via the Cisco Connect instead.. this had the Guest feature and Parental controls, but none of the other features I need, like QOS, or Port Forwarding, or DHCP disable.
It seems like the Web interface only configures some settings, and the Cisco Connect configures other settings, but I can't use them both.
Where does one set up the additional password for Guest access? Other than this, the router works fine on 2.4 & 5 GHz, nice..
View 9 Replies
View Related
Jan 3, 2012
I am tasked with configuring a 2504 wireless controller. Is it possible to assign an SSID to an interface that has dynamic ap management enabled?
Scenario:
Location1:
1) 10.0.0.0/24
2)192.168.0.0/24 DMZ
Location 2:
1) 10.0.5.0
Both locations are routable using network 1 at each location. However, I need to configure several access points and send them to location 2. These access points will communicate with the controller at location 1 on network 1. Two SSIDs will need to be on network 1 at location 1. The other SSID will be on Network 2 at location 1. This network is not routable.
View 32 Replies
View Related
Mar 11, 2013
This is a working example using static. But it doesn't work with the dynamic interface or I'm doing something wrong. Need to get rdp access to my laptop.
ASA Version 8.4(5)6
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]...
View 1 Replies
View Related
Feb 3, 2011
I have a network with Two 3800 Cisco Routers as Central and many Cisco 2811 Router as Branches. Now I set two Tunnel on each router connection Interface FastEthernet from each 2811 to SubInterface Fastethernet on 3800. I set OSPF as Routing Protocol and I configure QOS on Tunnel connections. Then I have a safe connection with backup connection between 3800 Router and each 2811 Router. Now I want to set VPN with IPSEC and Certification Authentication with CA Server for Security all connection. I set IPSEC and ISAKMP and Certificate on each Router and Set Dynamic VPN on Cisco 3800 Router and Static VPN on each Cisco 2811 Router. Now when if I configure tunnel with Crypto map, it works correct and all packets are encrypt. But if I try to set crypto on physical Interface(because I want to set qos on tunnel then protect packets on physical interface) however all packets are routed but crypto and encrypt d o not work. Set qos on tunnels and crypto on fastethernet interface.
View 4 Replies
View Related
Sep 29, 2011
I've been having this issue where my wireless network completely disappears from my computer and it requires a restart to fix.I know for a fact that it is not my modem/ISP as my iPad still connects just fine to the network.My network disappears about after 10-20 minutes of being logged on.
View 1 Replies
View Related
Aug 3, 2009
Have 13 DCS-920 Every few days a few random cameras will will hang/become unresponsive at random intervals. The cameras require that I unplug the cameras before they will respond. When the cameras are unresponsive I cannot access the camera via a web browser, the D-View Cam software, or the setup wizard. This is a problem as they are all mounted in positions requiring a ladder to access.
I have some connected via 802.11g and other hard wired over 10/100 cat-6 Ethernet cable.
View 14 Replies
View Related
Sep 10, 2012
How to setup dynamic dns for Cisco 2621xm ? What IOS support Dynamic Dns?
View 3 Replies
View Related
Mar 28, 2012
I live in a condo building that uses 3 Cisco Catalyst 3550 switches connected to a Comcast router with 100 Mbps download. Currently we regulate bandwidth by providing each user with 3 Mbps download. Even if only two people are active they still only get 3 Mbps download. I would like to set it up so if two people are using they each get 50 Mbps; a sort of 'dynamic qos. Is this possible with these switches? Would we have to purchase a Cisco router in order to provide this feature?
View 9 Replies
View Related
Nov 21, 2012
I'm working on setting up a template configuration for the Cisco ASA 5505 device that we'll use to configure more routers for various client needs. One of the requirements requested of me is the following: Internal hosts assigned a DHCP address are blocked from the internet Internal hosts with a static IP are permitted access to internet All internal hosts can communicate regardless of state
Now, I'm fairly new to this and I'm certain my terminology isn't correct so googling the problem has been fruitless. I have followed basic configuration guides and have configured the device to hand out DHCP addresses to hosts plugged in ports 1-7. If I'm plugged in and specify my address manually in the OS I am blocked from any access so I can only assume there is an access policy or some rule preventing me from authenticating against the router despite having set up VLAN1 to be the entire class C subnet. What sort of steps would I need to do to configure this? New access lists. For the record, the dhcp addresses are in the range of 10.100.31.64-10.100.31.95. VPN users are assigned an address from 10.100.31.220-10.100.31.240 and there seems to be no issues with that configuraiton. I don't wish to constrain what addresses a user can use should they specify a static IP (10.100.31.5 should be just as valid as 10.100.31.100).
View 10 Replies
View Related
Jun 7, 2013
Have an SRP527W that I've had a couple of years,
Model:SRP527W, ADSL2+ AnnexA, 802.11n ETSI, 2FXS/1FXOVersion ID:V03Hardware Version:4.0.0Boot Version:1.1.17 (Jan 4 2010 - 21:15:46)Firmware Version:1.01.29 (002) Mar 29 2013ADSL Firmware Version:0.78.0Recovery Firmware:1.01.20 (011)Setup Wizard Version:20110728.00
As indicated in the subject, wireless users are finding that it is either unattachable (shows up in the list but fails to attach) or if you manage to authenticate and get in, it's painfully slow or simply drops out. Security is WPA-PSK. Only noticed the issue after a couple of Windows 8 laptops came into the household, but the problem still seems to be there when they are off so not sure if they are connected in some way or not. Updated to the latest firmware - no change. Wired connections are fine and when it's initially restarted, so is the wireless, seems to happen sometime after wireless services are restarted. Only the one Wireless SSID, nothing fancy, max users around 5, all on laptops or the odd pad. I changed channels done narrow wide etc, (using mixed mode - some Wireless N laptops some Wireless B/G. Nothing seems to make any difference. No log entries until the Wireless system is restarted, doesn't require a reboot of the router, just a SUBMIT of the existing wireless settings to force it to restart.
View 8 Replies
View Related
Jan 29, 2013
Currently we have 20 remote sites, each with 2-5 AP's each. They all connect back to our Main Data Site in the US and register on a single WLC5508.
We do not have a backup WLC, but are looking to purchase one. What I would like to know is, are there any problems with the secondary WLC being installed in our Main Data Site in Europe? These two main sites are connected via a 10M MPLS WAN.
So all the remote sites could still connect to the WLC in the US, but in the event of a WLC failure in the US, they would need to fail over to the site in Europe
View 5 Replies
View Related
Feb 6, 2013
I'm using WLC5508 /w 7.0..My client do not get its IP. Status shown "DHCP_REQD".I found in (Cisco Live) Troubleshooting Wireless LANs with Centralized Controllers This related with Enable/Disable DHCP Proxy checkbox. I solved. with Enabling this.But,
1) Why this box have been working correctly for longtime? No one did diable/enable this feature on my box.
2) I guest, ver7.0 Disables this chechbox by default. Or not? I also have others two 7.2 boxes. Those are all Enabled.
View 7 Replies
View Related
May 30, 2011
I have access to free wireless service but it requires a security key? How do I get this key?
View 3 Replies
View Related
Feb 4, 2013
I have a WLC5508 , we are using external DHCP for WLANs
one WLAN is able to get IP from DHCP server but another WLAN not , the DHCP server is same , only 2 different scopes.
This is debug
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP received op BOOTREQUEST (1) (len 308,vlan 1, port 1, encap 0xec03)
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP processing DHCP
[Code].....
View 2 Replies
View Related
May 7, 2012
I have some problem about dhcp via VMware 7.1. My client connect the wifi and get ip address well, then, i turn on VMware (inside my computer) and set as the bridge mode. I found that my VM cannot get the ip-address from dhcp server and I using WLC5508 version 7.2. I try to connect via Switch, my VM get the ip address well.
View 1 Replies
View Related
Jun 6, 2012
looking at doing the site survey before detailed implementation. we plan to use a wlc5508, AP3602, a good tripod/stand, PoE switch and AirMagnet to conduct the site survey. i'm inclined to use a single AP and just a guest SSID and let AirMagnet merge the readings on where i 'locate' the AP (on 1 VLAN)
View 1 Replies
View Related
Apr 4, 2013
A customer have a bad coverage in a corner of his branch office. He like to add a mesh AP (MAP) in the near of that corner.
I checked allready the documention about Mesh but i'm not sure if Flexconnect and Mesh works togheter. This MAP is in a branch office and the WLC is in the head quarter therefore he likes to uses Flexconnect togheter with Mesh.
View 10 Replies
View Related
Feb 25, 2013
I have a customer who is going to deploy a WLC HA AP SSO setup. I have recommended them to have 4 Gigabit SFP modules in each WLC5508.The customer now asks if it is possible to only have one or two SFP modules in the standby unit ? As he says it is properly not going to go in service one time within the next five years if he is unlucky.
View 5 Replies
View Related
Feb 6, 2013
We have five cisco WLC 5508 and one WCS .The WLC is running on 7.0.116.0 version at present but we want to upgrade it to 7.4.100.0 but on cisco site at download location , the below thing is mentioned...
WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time
Access Point Model----Cisco 3501i Series
So i want to know, can i upgrade it to this version when we are having the WCS in our network ?
View 16 Replies
View Related
Jul 25, 2012
So I have a WRT160N firmware v3.0 wired connection to my PC, and at least once a day my connection speed drops from 2mbs down to almost dial up speeds at 60kps. Just unplugging the router then plugging it back in seems to fix it every time. I've contacted my service provider and they say there's no issue on their end, and since I don't get this problem when I plug the modem directly to the PC I agree with them. I've done a factory reset and that didn't work. I've gone through the FAQ and can't find anything useful in there.
View 7 Replies
View Related
Sep 9, 2011
My ISP here at my mother's in Italy (www.teletu.it) gave me the following configuration:
1. Supported Protocol: PPPoE or PPPoA
2. VPI: 8
3. VCI: 35
4. Encapsulation: LLC (If not supported: VCMUX/NULL)
5. Modulation: Multimode
6. Authentication Protocol: PAP or CHAP
if I connect my laptop to the ADSL modem, it all works just fine and I can connect to the internet (as you can see )
HOWEVER, if I then try to configure my WRT54G v6 to use this internet connection (I NEED to be wireless here, or I won't be able to use my iPhone and iPad), there is no way apparently for me to configure the Encapsulation, Modulation, and Authentication Protocol above. I just upgraded my WRT54G's firmware, and am now running firmware Ver.1.02.8, 10/05/2009. I was hoping this would allow me to set these parameters, but I can't find a way.
I tried just configuring the WRT54G with PPPoE and the ISP's userId/password, but this doesn't seem to suffice, and I don't see any other settings I could try.
View 3 Replies
View Related
Jul 15, 2012
I recently installed a Cisco X2000. Several PCs running Windows XP Pro connect wirelessly. Also, we have an Android device and iPhone connected to the wireless network. We have a network printer and network drive connected via wires to the router. Most of the time the router and cable modem features work well. However, every so often all devices lose wireless signal simultaneously. It is not possible to reconnect to the X2000 unless I unplug the X2000 and plug it back in. After this reboot, we can connect again. Obviously, this is quite frustrating. By the way, we get acceptable signal strength after the X2000 locks out however none of the devices (computers or phones) are able to connect.
View 1 Replies
View Related
Jul 28, 2011
I was excited to learn that USB printer support was added to the E4200. I'm disappointed to find that the USB printer option that is available in firmware version 1.0.02 requires Cisco Connect software. There is no version of Cisco Connect for Linux. I was hoping that this would allow the printer to be shared among my Win7 desktop, Win7 laptop, and my Linux desktop running Ubuntu 10.10. No such luck. WIth the printer connected to the router I can print with any one computer. My previous configuration had the printer connected to my WIn7 desktop so that desktop had to be turned-on to print. The bottom line is that I still can't print from the Linux box without turning on the desktop machine. Cisco please provide a way to connect to the printer without using the Connect software! Or provide a java version that can be run on any OS.
View 4 Replies
View Related
Feb 3, 2012
In one week I need to import the config from my 4404 WLC to my new 5508, then I just want to change the mgnt IP address of the 5508 and then bring it into the same mobility group.How do I import the config when the 5508 is straight out of the box?
View 13 Replies
View Related
Jun 22, 2012
I have a WLC5508 and 25 LAP 1041. I use two wifi, one with RADIUS for data and other with wpa-psk for voip. The problem is the voip conectivity is broken.How can i improve the handover?
View 11 Replies
View Related
Sep 15, 2012
I have WLC 5508 with 6.0 software and kept in main office and 10 sites are connected . I created Group and hreap for the sites AP.Now customer wants the secondary WLC to keep on one another site. And the customer is asking all the configuration like ap group and all should come to secondary wlc automatically . In future also if he create any new group in primary it should come in secondary wlc.And if primary goes down the secondary should controll all the sites and when comes up primary should taken care.Active standbye mode.
View 10 Replies
View Related
Nov 8, 2011
I have been asked to setup wireless and we have purchased WLC 5508 and 1142 APs.We have several remote sites and a centralized WLC. The requirement are to have a common SSID (Corporate) advertised across all the remote sites and have that SSID locally switched, and have another two SSID Guest and Mobile tunneled back to the central site (WLC).I want all the wireless (Corporate) clients to use the same subnet as the wired clients at each remote site, the IP assigment will be done by a DHCP server at the central site. The Guest and Mobile users will use a common subnet each across all the site and this will also be handled by the DHCP server at the central site.
I have enabled H-REAP with Centralized Authentication and Local switching but I'm not sure about the second part which is to have a common SSID (Corporate) across the remote sites and localy switched whilst having the other two SSIDs tunneled back to the WLC. Cisco TAC told me to configure dynamic interfaces for each of the remote site but then he said I still wouldn't be able to switch the Corporate traffic localy if I use a different subnet to the wired subnet for the wireless clients.
View 12 Replies
View Related
Dec 30, 2012
My problem ist that i have 4 air-cap-1552e APs witch are powerde trugh Power Injectors. They worked fine for a few days but then the controller (7.2.111.3) lose connection to them. Right now i have only one Joined AP. The other 3 are status not joined. I can Ping all 4 Aps and wifi clients are connected through them.
View 8 Replies
View Related
May 16, 2012
I tried to implement WLC5508 in my network but when I came to connect it to the switch core which is a Catalyst 4000 the link didn't get up. This switch module is a fastethernet, I wonder if that might be the problem since I also tried connecting my laptop to the WLC and the link got up.
If that might be the cause, is it possible to get WLC to 100 Mbps?
View 5 Replies
View Related
Sep 8, 2010
I have on my desk a WLC-5508 that I need to setup to ship to a remote location. Normally we configure 4402 model and this model/version appears to be much different. I am trying to configure just enough via the command line to access the GUI via a laptop directly connected to the device. I’ve gone through the Wizard Configuration Tool where you set the hostname, admin account, and management interface (among other things). We use LAG and tagged VLAN on the management interface. I’ve been told in the past this is how we configured the 4402 models via laptop directly connected once the GUI is accessible, but with LAG enabled I don’t understand how a laptop could communicate via trunk, so I've disabled LAG and set the VLAN to untagged. In either case the laptop does not communicate with the WLC. Skipping ahead to my current setup I see the following information via the CLI:
(Cisco Controller) show>interface detailed management
Interface Name................................... managementMAC Address...................................... IP Address....................................... 10.1.1.20IP Netmask.......................................
[Code]....
View 6 Replies
View Related
