Cisco Wireless :: 2960-C Client IP Not Received From 1140 LWAP
Mar 5, 2013
I am installing a small wireless network (for the firs time). The WLAN is connected to a router/firewall and consists of a Cisco 2960-C Series 8-Port Compact Ethernet Switch, a Cisco Aironet 2500 Series Wireless LAN Controller for Lightweight Access Points and a Cisco Aironet 1140 Series g/n Lightweight Access Points (five AP if I get it to work).
My problem is that when a client connects to the access point it does not get an IP-address.
In the WLC DHCP proxy is enabled and Internal DHCP server is used.
The scope is from 192.168.104.65 - 192.168.104.99
The WLC IP is 192.168.104.60
The DHCP server is given as 192.168.104.60
When starting the system I can see the the AP have the IP 192.168.104.66 so it seems the DHCP gives out IP-addresses. I can ping the AP.
When a client connects to the APit is asked for the security key and the client can be seen in the WLC monitor section. The client never gets an IP-address; in the WLC monitor 0.0.0.0 is shown.
View 4 Replies
ADVERTISEMENT
Apr 29, 2012
I have an environment of Cisco 5508 Wireless Controller and 1142N Access Points. I have a problem with the ratio of concentration of clients connecting to Access points in floors.
Recently I have been turning off 802.11a on the access points and I am seeing increase in client count in a few of acces points.What is the maximum client count supported by these access points and how do i ensure they are distributed evenly on access points?
View 4 Replies
View Related
Apr 23, 2013
I have one 5508 with Product version 6.0.199.4 and about 7 Cisco 1140 APs.We have a next problems. Go out of the connection on the clients PC, while physically a wireless connection to the workstations is not broken, but access to network resources is lost and restored after some time (up to about one minute).The logs on the controller at the same time see the following message.
View 3 Replies
View Related
Nov 28, 2011
We are using the CISCO-DOT11-ASSOCIATION-MIB in a Cisco Air AP 1140 device with release 12/4(21a)JA1 to find out the radio type of wireless client (B/G or N). The clients in question are of type Wireless N and Wireless B/G. We are querying cDot11ClientDevType and cDot11ClientRadioType but the relation between the returned values and client/radio type is not clear:
2 devices returned: cDot11ClientDevType = 102 ==> pc4500Client(102) - client with a 4500 radio and ClientRadioType=2==> ccxClient(2) - CCX- compatible radio1 device returned: cDot11ClientDevType = 1==> unknown (1) – unknown and ClientRadioType= 1==> unknown(1)
Questions: On a Cisco Air AP 1140 device
What OID needs to be polled to find if the client's radio type?What value is returned by this OID if the radio type is B/G?What value is returned by this OID if the radio type is N?
View 1 Replies
View Related
Jan 14, 2013
I'm running PI 1.2.1.012 and I'm having issues populating client information. Most of my switches are 2960 series. Specifically I get a lot of MAC Address "Unknown" and nothing in the IP address field. I probably get about 25% of the correct MAC address and 10% of the IP addresses. I also run CiscoWorks Prime LMS 4.3.2. and the user tracking information is about 98% correct pertaining to MAC address and IP address. My other network management tools also are very accurate.
View 1 Replies
View Related
May 20, 2012
We're in the process of upgrading our Wireless AP's from autonomus to LWAP. We're doing the upgrades remotely (we have 100's of sites to do, and it's not possible to be there to console on to each one), using a local computer to upgrade them to LWAP's with the Cisco Upgrade Tool.Having some inconsistent bugs pop up though from time to time.The most common one is that it basically buggers up the IP address after applying the recovery firmware image. It's supposed to keep the IP it had according to the IPFile.txt (for example 172.25.25.4), but it does something very weird... it keeps the last two octets (so 25.4 from the e.g) but replaces the first two octets with a 192.168 address. So the final address in this example after the UpgradeTool has done its work, is 192.168.25.4 - which is compeltely wrong.
This causes it to be unable to talk to the WLC (obviously, with bogus IP information it will struggle), and gives us big problems in that it wont ever come up unless someone can console to the AP and fix it. We can usually resolve the issue by munging about on the switch - switching the port it's connected to between access and trunk and doing some shut/noshut cycles seems to do the trick mostly.
View 9 Replies
View Related
May 15, 2012
i have out of box 20 AP 1100 LWAP...and cisco 22XX WLC......i need few information
1- what is option 43 in DHCP once i take the AP out of box shd i config static IP for managment
2- How LWAP register to WLC?
View 1 Replies
View Related
Jan 17, 2013
I was looking for a way the manually re-authenticate dot1x client from cli and found this: [URL]
"You manually reauthenticate the client by entering the dot1x reauthenticate interface interface-id privileged EXEC command"
I've tried it 2960 with 12.2(58)SE and 15.0(2)SE, but it doesn't seems to be implemented. Have I missunderstood something? Or do you guys have any other command to accomplish a manually re-auth?
View 6 Replies
View Related
Dec 5, 2012
I have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
View 3 Replies
View Related
Aug 18, 2011
I have an AIR-AP1242AG-E-K9 which had c1240-k9w8-mx.124-21a.JA loaded, I followed the link below and upgraded with Cisco’s upgrade tool to c1240-rcvk9w8-mx with no problems at all, after the upgrade I could then see the LWAP on the 4402 controller and had it working a treat.Now the problems begin, I brought it into the office where we have 5508 controllers, plug in the LWAP into our management switch and boot it up I get an IP assigned from the DHCP server and the AP goes into discovery mode but never finds the controller.I have logged the boot process but this does not give much away, our other 1100 series AP’s boot fine,
[URL]
Console Boot Log.
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
[code]....
And that is where she sits and does nothing more, I have noticed the DNS problems but the other 1100 series LWAP’s boot up after show that same issue.
View 2 Replies
View Related
Jun 20, 2011
Is it possible to Change IOS of 1252 LWAP AP to Autonomous AP? I have seen some documents for changing Autonomous AP to LWAP and change back procedures.
View 4 Replies
View Related
May 7, 2012
I have a 1121 autonomous AP which I switched to the lightweight mode by copying the LWAPP ios to its flash and issuing the command boot system flash IOS_file_Name. After that I was unable to associate the AP to my wireless controller because it was continiously rebooting. Unfortunately this AP does not have a console port so I can access the debug and see what is happening. And I was not able to switch it back to the autonmous mode becaus the AP won't accept the Autonomous mode IOS anymore.
View 2 Replies
View Related
Feb 28, 2012
We had core(4503), distribution(3750), and access switches(2960) in our environment. Currently we configured the clock manually in each switch, but a reboot of the switch resets the clock also. We are planning to make a single switch as a NTP servers and others are clients to synchronise the correct time even after a reboot of the access switches.
View 6 Replies
View Related
Apr 4, 2011
I would like to convert some 1142N LAP to Autonomous. Is there a way to do ?
I have noticed a new image : c1140-k9w7-tar.124-25d.JA.tar
I don't see a way to replace the image in flash ?
View 1 Replies
View Related
Mar 5, 2013
I have a 3502 AP that I am attempting to set back to factory default including clearing the username and password. It is going to work off of 4400 controllers. I have read numerous documents no how to clear the config and password but so far nothing has worked. I can get it into ap: mode but not sure what to enter here. When I do a dir there doesnt seem to be any files. It will pull an IP address via the local router but cannot communicate with WLC.
View 28 Replies
View Related
Mar 11, 2013
I am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. If i add some config in primary controller or do some changes or reboot all the AP's are moving to backup controller. this doesn’t have any problem, but many AP's which moved to backup controller are losing VLAN mapping. This happens every time. Primary --> backup, backup --> primary. Both controllers have same vern...same config etc..
AP model: AIR-LAP1252AG-A-K9
Controler model: AIR-CT5508-K9
View 15 Replies
View Related
Apr 10, 2013
I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.
View 2 Replies
View Related
Jul 7, 2011
I have a customer who accedentally got a AIR-LAP-1141. He needs it to be autonomous. If I convert from LWAP to Autonomous, will there be a licensing issue?
View 1 Replies
View Related
Jul 10, 2012
We have few sites with old 1232 ag AUTONOMOUS existing AP's , They are connected through 1 mbps link to main office .Now we are planing to upgrade with WLC 5508 and few 1140 ap . but we want to use these same 1232ag ap on some sites.So we need to upgrade it to LWAP .
1>Is it possible to upgrade this model of AP
2>Which is the ios i should download , is it avaliable in cisco site (as this ap is end of sale now )
3>How the step to upgrade this autonomous ap
View 3 Replies
View Related
Jun 13, 2012
We have just installed our first CT2504.After install I have found a dramatic drop in signal strength compared to the wireless survey result obtained.All of our site surveys include real world testing using an AP, in this case a AP1041N.In doubt I retested a section using an AP1041N in the same location as one of the recently deployed LAP1041N.
In the same location a LAP1041N has between -10 and -20dbi difference in SNR compared to the test AP1041N.For example locations that tested with -60dbi using an AP1041N have little to no coverage using the LAP1041N installed.This applies irrespective of the WLC automatic control over Tx power or manually setting the LAP TX to the highest level.
View 5 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
Jul 12, 2012
Is Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?
View 1 Replies
View Related
Nov 20, 2012
how to disable radio on the AP 1140 from NCS script .
View 5 Replies
View Related
Jan 28, 2009
I tried to find the radiation pattern for the 1140 AP, but no luck so far. Where to find it?
View 7 Replies
View Related
Apr 18, 2012
I need a legible radiation pattern graph for the 1140 AP -- the antenna pattern. This is for a wireless deployment application which models signal strength. It needs to be specific for the 1140 AP as the antenna has a Maximum gain of 3 dBi which is different than the antenna gain on the 1130 AP.
View 2 Replies
View Related
May 31, 2012
We have two WLC's 5508. Following are its interfaces & details:mgmt 10.49.5.251 on wlc1 & .252 on wlc2 access p 10.49.6.251 on wlc1 & .252 on wlc2 there is no AP manager interface seen on both wlc's nor configured. both wlc1 & wlc2 are connected each to two switch ports, configured as normal trunk link each.LAG is enabled on both WLC's.
View 2 Replies
View Related
Sep 29, 2011
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies
View Related
May 12, 2011
To lay it out, I recently installed 4 of these in a new office space. We have them connected to a 3750 stack....
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 54 WS-C3750X-48P 12.2(53)SE2 C3750E-UNIVERSALK9-M
2 54 WS-C3750X-48P 12.2(53)SE2 C3750E-UNIVERSALK9-M
3 52 WS-C3750-48P 12.2(53)SE2 C3750-IPBASEK9-M
[Code].....
as you may notice, port f5/0/36 is showing not conencted. This is the case even if I move this LWAP to one of the other 3 ports that are working or even a port on one of the other 3 switch models in the stack. I troubleshot without cross connects, I changed port configs, I changed cables, but I still do not get a link. The LWAP does get power though and will start to boot, but then the status light on the top will just blink orange. sounds like the LWAP is broken.. BUT - if I move this LWAP to a port on a 6513, it connects to the switch and links to the WLC just fine.
View 6 Replies
View Related
Dec 19, 2010
I just installed an Aironet 1140 to replace a Netgear ProSafe access point that I had in my network prior. I'm having one issue that I can't figure out though. None of the client PCs can establish a connection to an external (over the internet) VPN server while on the Aironet wireless. If i unplug the AP and plug a PC into the same port that normall feeds the Aironet I can VPN just fine.
Is there any "VPN Passthrough" option that needs to be enabled somewhere on the 1140 that is blocking this traffic for some reason?
i'm running the following IOS BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1) and I've included my running config below
Current configuration : 2092 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname ap!enable secret 5 [omitted]!no aaa new-model!!dot11 syslog!dot11 ssid MetroC authentication open authentication key-management wpa guest-mode mbssid guest-mode wpa-psk ascii 7 [omitted]!!!username Cisco password 7 [omitted]!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 no dfs band block speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.1.3 255.255.255.0 no ip route-cache!ip http serverno ip http secure-serverip http help-path [URL]
View 9 Replies
View Related
Mar 28, 2012
I try to setup a 1141 aironet AP to authenticate my user through our Ms Radius Server ( Win 2008 R2).Everything is fine with small Bussiness AP WAP4410N with the following configuration:But I can't setup successfully the aironet 1141 with the same settings and getting it works.Here is my configuration for the Aironet 1141 Vlan 1 is the ssid I want to get it work with Radius.
View 1 Replies
View Related
Dec 16, 2012
We have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
View 3 Replies
View Related
Dec 10, 2012
If I do a speed test (bandwidthplace.com) while connected to a remote locations 1140 standalone access point, the download/upload speeds are roughly 100kbps. There are no other devices connected to the access point at the time. Wired PCs on the LAN that the access point is connected to are not having a problem.Pings from the laptop, through the access point, to our central WAN router are at <10ms.The WAN circuit (remote location to headquarters) is 5Mbps. No congestion.Circuit out from headquarters to I'net is 50Mbps. No congestion.Access point and router interfaces show no errors or collisions, etc. The configuration is the same as 28 other standalone access points in 28 different LANs on the WAN. They have no problems.
View 5 Replies
View Related
Jan 2, 2013
I have 3 Cisco AP 1140 at my customer (Service Industry) place, so they requenst us to provide Hotspot solution to them for managing the Internet connection for limiting to their Customers over the account system. Let me know how i can integrate hotspot BOX with Cisco AP.
View 3 Replies
View Related
