Linksys Wireless Router :: WRT54GS Factory Defaults / Resetting Connection Type From PPPoE To Bridge
Jan 17, 2012
I'm having a very difficult time getting my WRT54GS to work with my Westell 6100 modem. I've been bouncing around gathering info, and what I've learned is that the goofy way CenturyLink tech support told me to hook up my old wired router (modem line into outgoing (LAN) router port) is because the Westell 6100 is a "smart modem/router". Therefore, when I run the Linksys setup CD, it sees the modem as a router, and won't properly configure. I've also learned that the Westell modem can be "dumbed down" into simply a modem by putting it into "bridge mode", which is where I'm at right now - trying to get it reset to factory defaults and resetting the connection type from PPPoE to Bridge. In the meantime, I also reset the WRT54GS to factory defaults, and now I've got another problem: the router will not allow me to set up encryption. The default setting is "Disabled", and when I click the down arrow and try to make any selection at all (preferred selection is WPA2 Personal), it reverts to Disabled. I've also tried to change the router's IP address to 192.168.2.1 (and alternately to 192.168.1.253), so it won't conflict with the modem's IP, and it freezes up every time I try.
View 2 Replies
ADVERTISEMENT
Jun 23, 2008
I reset my WRT54G wireless router, so I could use the default password for 192.168.1.1 and the default password and username still do not work.
View 6 Replies
View Related
Jan 9, 2010
WRT160Nv3 Firmware Version: v3.0.02
I've been using Linksys for years but the last two routers I have purchased have been very problematic.
- My router hasn't had this problem before. The other day I was downloading 4 games at a time from STEAM, when I got home from work I found that my router had completely gone back to factory settings. So I configured my DSL PPPoE, SSID, Wireless Security (WPA) changed the default admin PW and about 20 minutes later it was back to factory again.
I've done a "hard" reset and reconfigured and still it resets itself. What's also upsetting is this completely opens my network up to ANYONE when this happens...
So far in the past 2 days I have (now using a backup restore file) re-configured the device 10 times.
The only thing I can think of is that I just got Windows 7 the same day this started happening. I thought it could be STEAM as well so right now I have STEAM closed to see if it resets while it isn't running.
Could TOO much demand on the router cause it to completely reset itself to factory config?? Seems to me like there's a huge firmware or hardware problem here.
I have other friends and even co-workers that also have problems galore with their Linksys products...No other router it seems has as MANY issues as Linksys. Hat to say it but my next purchase most likely will not be another one of their products. This just shouldn't be happening.
View 5 Replies
View Related
Apr 14, 2011
I have tried to reset a Cisco 2811 to factory defaults to no avail. The system is locked, meaning it's set to go immediately to username and password before doing anything else after boot up. I cannot get to ROMMON, nor can the CTRL-B break sequence allow me the option. THere is a "no-password recovery" option that apparently is set (or unset?) but I cannot work with that.
I am a newbie with the routers, but I have tried various CTRL-B breaks from bootup, to particular times through the boot up sequence.
I do NOT have "enable" (also known as "privileged EXEC") access on the router. The router, when purchased, had a username and PW that is required to even get to the basic level 1 access. Without it the PW, I can't even get to exec mode.
View 5 Replies
View Related
Jun 14, 2011
I have a Linksys SRW2008MP that I am trying to reset to factory defaults. The guy who set this up is no longer employed at my company, and I do not know the IP address to login with a web browser. The switch does not have a reset button on the back. I follow the instructions from Cisco's website, which include connecting a console cable and using HyperTerminal to login. I can connect to the switch and watch it boot up in HyperTerminal. However, when I get to the point of inputting user name and password (which should be 'admin' and '<blank>', I can't figure out how to make to terminal emulator accept the input (much like pressing the Enter button in a web browser). According to the pictures on Cisco's website, there should be an Action -> Edit -> Execute option down below the login, but I don't see it, so maybe the switch has to verify my credentials before I get to that prompt?
This is the first time in my life using HyperTerminal, and I think that's where my problem is. How do I get HyperTerminal to accept my input?
I have also tried using TeraTerm, a different console cable, and a different computer.
View 3 Replies
View Related
May 22, 2013
I have an 1841 (256M w/ crypto card) that stopped booting. I reset it to factory defaults as per Cisco's directions, then began to setup with Cisco Configuration Professional. On the next reload I get this:
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
[code]...
The ios on the flash is "c1841-advsecurityk9-mz.124-22.T.bin"
View 4 Replies
View Related
Oct 26, 2009
We've lost our WRT120N's administrator password and are trying to reset it to factory defaults.One peculiar thing that we have noticed is that the router has an IP of 192.168.106.1 rather than the default of 192.168.1.1 (this is verified by the default gateway, as well as a login prompt when 192.168.106.1 is put into a browser).Things we've tried to do to reset the router:
1) Press and hold the reset button at the back of the router for 30 seconds
2) Press and hold the reset button at the back of the router for 60 seconds
Interestingly, doing either of these things seemed to have no effect on the status lights.
View 9 Replies
View Related
Mar 9, 2013
today I got up and discovered that my WRT160Nv3 router has resetted to factory defaults itself, the name of the Wifi network was "linksys" and all configurations were the defaults...
That's normal? This is the first time it happens.
View 2 Replies
View Related
Aug 10, 2011
I flashed the firmware and the ipv6 automatic is on disabled and I cannot set it to enabled.the 6rd tunnel option I can change but that has not effect- in fact from what I looked up it seems to be something used by some cable providers.hate to have to reset the router to factory defaults and then reset the network up - just to see if i can get the option to set IPV6 auto to enabled.
View 3 Replies
View Related
Sep 16, 2010
I just upgraded to a E3000 from a WRT54G and I am having some issues with network speed.I have no special settings and have even tried restoring factory defaults and upgrading to the latest firmware to no avail.The time I notice the biggest hit is when transferring files locally on the network (WiFi and LAN).Let me note that I do know the difference between MB/s & Mb/s and the like.I have Comcast 20Mb/s Down, 1.5Mb/s Up (just a FYI, the main issue is local transfers)
With default settings my Laptop (ASUS N82JQ, Atheros AR9285 Wireless Network Adapter), connects to the router at only 65Mb/s (with full signal).Upload seems to be more decent ~600KB/s (Transferring files from wireless n laptop to the gigabit desktop).Download seems to be limited to ~150KB/s (Copying files from the wired gigabit desktop to the wireless n laptop).These speeds are horrible! ~5hrs to transfer 3GB of data!
One of my laptops had a card that was capable of both 2.4 & 5Ghz and I was previously getting ~2000-5000KB/s (2-5MB/s) transfers with this router (But I had to do a system restore on it and reset the router). My ASUS laptop seems to only work with 2.4Ghz though. If I change the 2.4Gh Wireless settings on the router to "Auto(20MHz or 40MHz)" the laptop will connect at 150Mb/s, but the speeds are the same slow speeds as above.
View 9 Replies
View Related
Aug 11, 2008
I have a WRT54G router Ver. 5 with firmware v. 1.02.5. This is the second time this has happened to me but the router reset itself to the factory defaults. I lost all my configurations. I'm saving the configuration this time but it will be annoying to keep having to reconfigure the router.
View 9 Replies
View Related
Aug 2, 2011
I have a WRT54GS wireless router. I can successfully set up the router with my DSL modem for PPPoE. Here's my problem. The router configuration requires you to put in the userID and password, then logs you in to your ISP automatically. I DON'T want it to do that. Is there any way to configure for PPPoE where ISP login is controlled manually; i.e., when the user tries to connect to a web page, a dialog pops up for entering the password?
View 1 Replies
View Related
Apr 3, 2012
Last year our Network Security Supervisor submit his resignation and unfortunately did not endorse us the admin password we already tried the password he suggested when we contacted him but nothing of them works. Is there anyway we can reset the password without resetting to factory default?
View 1 Replies
View Related
Dec 6, 2011
I recently changed my internet connection to DSL from Cable, so now I'm using PPPoE type of connection.
Right now my router is configured as Automatic DHCP with the modem doing the PPPoE connection. All is fine and well.
Since I own a PS3, and Nat Type 3 conection is really bad for my online gaming, I would like to bridge my modem and connect to the internet through my router. That way I can properly forward my ports, use QoS and effectively get a better connection on the PS3.
I was able to successfully bridge the modem, but the PPPoE config on the router isn't able to connect to the internet.
Modem and router have been reinitialized after the configurations were changed. I do have the username and passwords, and they were properly put on the router.
View 1 Replies
View Related
Aug 28, 2011
I have an 1142 AP that I am unable to set back to factory defaults.Here is what I have done so far:
- boot AP while holding down the mode button
- ap: delete flash:private-multiple-fs
- yes
- ap: boot
- when the AP boots fully I try and enter any lwap ap commands and get "ERROR!!! Command is disabled"
- the AP name and password were reset to defaults but I am unable to get the IP address cleared.
I've also tried "clear lwapp private-config" and get an error saying the command is disabled.
View 4 Replies
View Related
Jun 11, 2012
I've just bought a pair of WAP121 for testing and validation. I've set it up properly (user/password, IP, management vlan, NTP, SNMP, 802.1x, etc). So far, so good, everything worked as expected. I've downloaded the configuration to my PC, and also saved it to startup-config. I've powered off the unit, went for a coffee, and powered it back. All my settings were lost.
Tried to restore settings from the file downloaded to my PC, but no luck. After reboot, it was factory clean, no trace from settings in the backup file. I've set it up again by hand, power cycled it, and the **** thing reloaded to default settings.
Faulty unit, I thought, so I opened the other one I have, and repeated the whole thing, but same results. Test were made using the power adapter supplied but also tried with a catalyst 2960 with PoE.
View 3 Replies
View Related
Oct 8, 2011
Got a Belkin wireless modem router some 18 monthes ago, and after a bit of a struggle managed to set it up. It worked fine, aside from the odd depower repower. For some reason, it just stopped working yesterday. I initially checked all my cabling etc and everything seems fine. I next tried resetting my modem/router to factory settings. When I tried to install the Belkin software I fell at the first hurdle with a message saying "The setup assistant is not able to connect to the router". After googling my issue, I followed others advice and running the cmd setting and typing in "ipconfig" only to find that my media state was disconnected.
View 2 Replies
View Related
Oct 27, 2011
What is the procedure to reset a 1941 router to factory defaults? I just recieved my1 1941 router. I connected it up to my Mac using USB. I got loged in using the cisco/cisco login and it said it will only work once and that I should create a new account. So I entered the command as directed on the screen and it gave my an error about the command. I verified it three times and each time it rejected. While I was looking online for an answer the connection timed out and now I can't get back in.
View 1 Replies
View Related
Feb 28, 2012
I successfully pulled it out of the box and already broke it.
What I did to lose my connectivity to it (via IP, console is OK), but I'd like to start from scratch and during my learning/experimentation I will undoubtedly need to do this over and over until I get things right.
I've found various guides, none of which look like what I am after. Basically, I want to return this to the condition that it was in when it came out of the box. IOS is version 12.4(6)T11 .
View 2 Replies
View Related
Aug 25, 2011
I'm part way through trying to set a Catalyst 4510R to factory defaults, One thing I'm stumped on is how do i remove the Customer Disclaimer eg what commands do i need to remove this and any other customer text within the switch, see below copy of text from the switch with customers details omitted.
The ** computer systems and ** networks are only to be used in accordance with the** Electronic ** Media Policy. Please read
[Code]....
View 3 Replies
View Related
May 19, 2013
I wanted to load the factory defaults for my 881W so I could get a clean start. Following this Cisco article: [URL]. I used the following commands while tel netted in via an ether net cable to one of the ether net ports: router#configure terminal router(config)#config-register 0x2102router(config)#end router#reload System configuration has been modified. Save? [yes/no]: n Proceed with reload? [confirm] .
Once I hit enter to proceed with the reload, the router power cycled. From that point forward, I never got a link light or connection via my ether net cable to the router on any of the ether net ports (0,1,2,3). I can get a link light on WAN FE4, but no DHCP ip address to telnet in. I do not have a Cisco USB console cable, which is why I've been trying this via my ether net cable. Hopefully, I didn't ***** up the router.
View 1 Replies
View Related
Jan 5, 2012
I have a used 1252 wireless AP. I can't get into it. How do I reset to factory default?
View 1 Replies
View Related
Jul 22, 2011
specs: linksys router wrt160n v3, verizon modem gt701c, windows xp service pack 3, verizon DSL, southern california.I have been able to connect to the internet directly through the modem only...but i need my wireless back working. I've reset my router a few times recently trying things i've read on forums from people with similar problems. The most recent thing i did was RESET the router -> connected modem/router/computer properly -> turned them all back on in the proper order -> check to see if websites would open. They didn't so i tried doing this, which was suggested...i plugged the router into the computer and enabled MAC address and then pressed the Clone MAC address button and saved....then I tturned everything off again and rebooted everything again in the proper order and still couldn't load any web pages. Here are my IPCONFIG/ALL read outs for both when i'm hooked up with the router & modem (which isnt working) and directly to the modem (which is working) this is the one with the router & modem:
C:Documents and SettingsOwner>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : shakas
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
[code]....
My modem and wireless were working fine for years...and then recently without me doing anything my modem kept dropping connection and the internet and dsl lights kept flashing and then going back solid....so i'd be connected for a few minutes and then they'd start flashing again over and over all the time. I finally called verizon and then had me fiddle around with stuff...followed all their directions...but ended up only being able to connect while directly connected to the modem. Even then, the modem was still losing connection and getting it back. (i was supposed to schedule a house call for a tech to check it out, never did) Over a couple weeks the connection ended up getting better on its own, so now it pretty much never drops out anymore. (almost) i've reset my modem, i've reset my router....i just still cant seem to get websites working with my modem and wireless router connected.
View 3 Replies
View Related
Sep 23, 2010
I purchased a WRV210. I configure the device, setup all my tunnels, WAN, LAN, Wirelss, Security, etc. and within 48 hours it "automatically" resets itself back to "out of the box" settings. This has happened twice now - once after it ran for about 4 days and the second time after only 5 or so hours of opperation.
Is this a known issue with the device? Is there an update I need to apply? I'd give ya my current FW version but I cannot login as it appears to have rest once again lol - and my tunnels are down so no remote access.
I made a backup of the config after the first unscheduled reset - (.bin file) so I have my settings ready to restore.
View 6 Replies
View Related
Dec 11, 2011
The IP address is unknown and we need to reset the switch. SInce we can't access the configuration menus. I was wondering if we could reset this device to factory defaults another way. I couldnt locate a reset switch.
View 2 Replies
View Related
Jul 4, 2011
PIX-515e reset to factory defaults
View 6 Replies
View Related
Jan 16, 2012
I have a cisco 800 that needs to be reset back to factory defaults. I tried typing in "config factory-default 10.10.10.1 255.255.255.0" at the conf t prompt, but I got an error Invaild input detected at ^ (the ^ is just under the word factory). So after a bit of reserch I came across this command "write erase" that seemed to do something but now I can't get any ip addreses. Here is the running config:
Using 1104 out of 131072 bytes
!
version 12.4
service config
[Code].....
View 13 Replies
View Related
Feb 7, 2012
I reset my Cisco 2911 ISR to the factory defaults. I then used the configuration guide to do the initial set-up through the CLI. I was able to assign IPs to the GE0/0 and GE0/1 ports. Now I cannot access the GUI device manager at all. I was able to ping the IP of GE0/0 so I know the adapter took the IP assignment, but still no GUI access.
View 7 Replies
View Related
Mar 7, 2012
I have been having some issues trying to stand up an older WiSM that has been incorrectly configured by my predecesssor and has a bad Mgt IP so I am unable to telnet or SSH into it, nor can I console or session into it.
What I would like to do is to change the Mgt address for the WiSM controllers (1 and 2) by way of the Sup (not sure that is possible) because as it stands they are set to 169.254.1.1 and are unreachable even when directly consoled into them.
Core-A#sh wism status
Service Vlan : 52, Service IP Subnet : 10.104.52.2/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Status
-------------------------------------------------------------------------------------------------------
3 1 10.104.52.3 169.254.1.1 4.0.217.0 Oper-Up
3 2 10.104.52.4 169.254.1.1 4.0.217.0 Oper-Up
Core-B#sh wism status
Service Vlan : 52, Service IP Subnet : 10.104.52.1/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Status
-------------------------------------------------------------------------------------------------------
3 1 10.104.52.50 10.104.30.254 7.0.116.0 Oper-Up
3 2 10.104.52.51 10.104.30.250 7.0.116.0 Oper-Up
I hope to get this WiSM setup on Core A and get it configured like I have my Core B and then run them in a dual failover design with load balancing between the two.
View 6 Replies
View Related
Nov 11, 2012
I am trying to setup a new LG dp200 blue ray player to my home network and cannot get it to connect, but i can use my phone on it and my xbox. Ive reset the modem and reset the player back to factory defaults after a few failed attempts.
View 1 Replies
View Related
Aug 22, 2011
I have a 4500 Catalysts switched (4510 R ) that require the configuration to wiped back to factory default setting, How would i go about clearing the configuration on each module board
The chassis consists of
2 x Supervisor engines v WS-X4516 with Flash cards
4 x WS x84448 GB RJ45 48 port switches
1 x WS x4306 GB Switch Module
I also have a Catalyst 6500 that requires each module within the chassis to we wiped back to factory defaults
1 x Supervisor engine WS X 6k SUP 2- 2GE
1 x WS X6416 G-Bic 16 port GB Ethernet
4 X WS X 6148 CE-TX Base T GE 10/100/1000
1 x WS X6348 48 Port Inline Power Capable
And i have a Catalyst WS - C 6513 with the following Module card that need the configuration wiped to Factory defaults as well
View 3 Replies
View Related
Sep 12, 2011
Currently I have Verizon DSL and which supplied me with a Westell 7500 modem/wireless router. I am also connecting a Linksys WRT54GS (firmware Version: 7.2.08) to the Westell 7500.
When I connect via cable or wireless to Linksys WRT54GS I am not able to establish VPN connection. I get the error “Error 619: A connection to the remote computer could not be established. So the port used for this connection was closed”.
However, when I connect via cable or wireless to Westell 7500 I am able to connect to VPN.
I tried resetting the Linksys WRT54GS to factory settings and reconfigured but no success to VPN.
At work we have a Windows 2003 setup with VPN Role on it and on my laptop I am using the built in VPN connection within Windows 7.
View 3 Replies
View Related
Dec 12, 2012
How do I get my router to connect to roku.When I enter my router password in Roku it doesn't find the router. And when I use Cisco Network Magic, it doesn't find the Roku device.
View 8 Replies
View Related
