Configure Tplink Modem On Repeater Mode In Order To Repeat Signal From (Huawei)?

Dec 4, 2011

That's y topology:

(TPLINK) /////////////// (Huawei)--->(internet)
...................wirless................cable

I want to configure my tplink modem on a repeater mode in order to repeat the signal from (Huawei) ...

View 1 Replies


ADVERTISEMENT

Wireless Repeat Wifi Signal Of Cisco Epc3925 Modem?

Nov 1, 2012

I am trying to wireless repeat the wifi signal of my cisco epc3925 wifi modem. The router i am using as extender is a netgear wndr3700. i dont have much knowledge about these thing and am losing so much time by trying to get it working. everytime i apply the settings in the netgear i am unable to connect to it (even wired) and have to hard reset it...attached are some screen shots of both devices from last settings I tried.

View 6 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR702N - Repeater Mode Signal Fades Out Or Does Not Work At All

Jan 31, 2013

Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.107 Build 121123 Rel.31456n
ISP : COMCAST

This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.

View 1 Replies View Related

Cisco Wireless :: WAP4410N Won't Repeat Signal

Jan 17, 2012

we purchased 8 WAP4410N access points to cover our entire school with wireless internet. 2 of those could not have access to a wired network accesspoint, so we wanted those to repeat the signal of 2 others. The ones who are to provide the signal are set up as access points, with the option to allow the signal to be repeated enabled. The mac adress of the other access point is provided, and the channel is set to 6. The 'repeat' 4410N ones are set up as wireless WDS Repeater, with the mac adress of the remote access point entered through the site survey. The channel is also set to 6.
 
When I connect with the 'repeaters' however, I only get limited access, cannot get on the internet, and I cannot change the network settings in Windows 7 from 'public' to 'business'.

View 3 Replies View Related

Linksys Wireless Router :: Configure WRT54G As Repeater Signal Of WRT120N?

Jan 2, 2013

Is it possible to configure the WRT54G as a repeater signal of the WRT120N?

View 1 Replies View Related

Using TPLink TL-WA801ND As Repeater And Connect PC Also?

Dec 26, 2011

I want to use TP-LINK TL-WA801ND as a repeater, at the same time I need to connect one PC to this repeater by UTP cable (the router has one RJ-45 port) will I be able to successfully connect this PC to internet using this router as a repeater ?

View 6 Replies View Related

Configuring TPLink WR841ND As Repeater?

Nov 30, 2012

I'm trying to configure mine as a wireless repeater, but to no avail. Here's what I've done so far: disabled WPS changed my router's IP to 192.168.0.2 (because the source router's IP is 192.168.0.1) rebooted the router enabled WDS, found the network I want to repeat using the Survey feature, then filled in the WPA2 password. enabled WPA2 security on my own repeated network, using the same authentication type and password as the original rebooted the router.

My router complains that "WAN port is unplugged", and it doesn't get a WAN IP or incoming packets, which probably means it's expecting the internet signal to come from the WAN port rather than the wireless network I set up, right? How can I force the router to connect to the network? Also, should both routers be in the same subnet? I've tried with different subnets but nothing changes. The source router is a D-Link DIR-600.

View 4 Replies View Related

Best Solution To Extend Signal Of Tplink TL-WR10

Feb 14, 2013

which will can extend the signal strength? changing antennas, put a wireless amplifier or buy ASUS 66U??change TPLink TL-WR1043ND to ASUS 66U ??? ASUS 66U is best to TPLink TL-WR1043ND and can extend the signal strength by up to twice the distance?

View 1 Replies View Related

Ta-wa500g - Using TPLink In Client Mode / No Internet?

Feb 28, 2011

I'm trying to connect a non-wireless enabled pc to my virginmedia network by using a tp-link ta-wa500g router in client mode. The pc connects to the router via ethernet fine, and i can access the router admin page etc., but the router doesn't seem talk wirelessly to the virgin box. it finds it and everything, but i can't access the internet at all. i've tried removing the password, resetting everything, I've upgraded to the latest firmware, but have come to a bit of a dead end.

View 1 Replies View Related

Linksys Wireless Router :: How To Use 2500 With Huawei Ws320 Wifi Repeater

Jun 12, 2012

I have set up my linksys in my main hall, i get a decent wifi signal in my room. But i get very very poor signals on my phones (bb9780 and Samsung S2). I bought a Huawei WS320 wifi repeater. how to connect these two so that i can get a strong enough signal in my room ?

View 2 Replies View Related

Using Tplink Tl-wa5110g Wisp Client Mode With Wireless Router?

Jan 2, 2013

I have a WISP internet connection. i have a Acess point tplink tl-wa5110g . i set it to wisp client router... My final goal is to share my wisp internet wirelesly.

Now i want to ask what i have to do next. do i need wireless router and connect it with the Ethernet port of the acess point..

View 1 Replies View Related

Cisco Switching/Routing :: Configure PPPoE On 831 Router With Modem In Bridge Mode

Sep 7, 2012

config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]

View 2 Replies View Related

Cisco WAN :: 2821 - Configure Router To Use 2 ADSL Lines With Dialer And Modem In RFC2684 Mode?

Mar 9, 2011

I want to configure my router to use 2 ADSL lines each with a dialer and a modem in RFC2684 mode. I have a 2821 (IOS 12.4) with an HWIC-4ESW.
 
My network topology is like this :

ADSL Modem 1 (RFC2684) --
(Fa0/0/0)
Router -- (Gi0/1) MyLAN
(Fa0/0/1)
ADSL Modem 2 (RFC2684) --/
 
1. I configure my DSL Modem in RFC 2684. The first use 172.16.0.2/29 and the second 172.16.0.3/29. I connect this devices to Fa0/0/0 and Fa0/0/1.
 
2. I configure Vlan1 to use the network configured on my modem :

interface Vlan1
ip address 172.16.0.1 255.255.255.248
 
3. I try to ping my devices :

#ping 172.16.0.2
 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.3, timeout is 2 seconds:
!!!!!

[code]....

View 3 Replies View Related

TPLink TL WR741ND - Router Setup With USB Modem?

Dec 26, 2012

I've got a a tp-link TL-WR741ND, but I don't have a ADSL2+MODEM ROUTER, (ADLS MODEM). Instead I've got a orange usb modem, how can I install the device?

View 2 Replies View Related

Huawei B660 3G - Can 3G Signal Strength Weaken With More Concurrent Users

Jun 4, 2013

I'm using a Huawei B660 3G router at my house, with with a service provider called 8ta (in South Africa). I've been struggling for months to try and get them to troubleshoot and fix my connection, which was working fine for about a year.

I'm now daily struggling with download speeds of as little as 0.1Mbps to 0.5Mbps, especially after 5pm until about midnight. Upload speed off course is even worse.

8ta, has after months of me complaining agreed to install an antenna at my house, which will probably take another few more weeks for them to accomplish.

I often have 5/5 bars of signal on the router, so my argument is that signal strength might not be the problem. Since the connection is in a residential area, I would assume that their network is more likely to be a bit more congested after hours, but a technician explained to me that their network is never more than 30% "occupied".

Can the number of users connected on the 3G network/tower cause signal strength to attenuate for surrounding users?

Would it replace the B660 (7Mbps) router with a 21Mbps counterpart?

View 2 Replies View Related

Configure IP Filtering For Huawei HG520b Router?

Jan 17, 2013

If you are familiar with the Huawei HG520s router, I want to filter an ip range (ex. 192.168.1.10 to 192.168.1.255) so that no other users can connect on this ip range and start using the router.

View 2 Replies View Related

Huawei USB Modem - Cannot Connect SSL Sites Through Proxy

Apr 17, 2011

I am using a USB Modem from HUAWEI Technologies to use internet when im not on a wifi zone.. The Internet Speed is kinda slow (512 kbps), so I configured my browser to go through a proxy to make it a lil bit faster (2mbps now)..Everything works fine except that I couldn't connect to https sites (gmail, facebook, eBay, etc)

View 3 Replies View Related

Connected To Internet Using Huawei Wireless USB Modem?

Feb 16, 2012

I am connected to the internet using a Huawei wireless USB modem connected to my desktop computer(no other type of service available) I would like to set up a Wifi home network so that I can connect using Wifi to all of the other gadget that I have in the house. So the question is can I connect a Wifi router using a ethernet cable comming from my desktop computer? and if so what router would you recommend for this application?

View 4 Replies View Related

TP-Link 3G/3.75G Router :: Using MR3220 With Huawei E3276 Modem?

Feb 5, 2013

Region : Finland
Model : TL-MR3220
Hardware Version : V2
Firmware Version : Newest
ISP : Sonera

I have a TP-Link TL-MR3220 and Huawei E3276 USB-modem (Sonera, Finland)Is there some update or advices, that can i use this huawei with MR3220? Or when update releases?

View 7 Replies View Related

Cisco Routers :: RV215W With HUAWEI E398 Usb Modem?

Jan 16, 2013

I'm trying to setup a Huawei E398 from Swiscom (switzerland operator) and my CISCO RV215W cannot detect him. Is the RV215W compatible with the Huawei E398 USB LTE Modem?

View 2 Replies View Related

Wireless Repeater Signal Keeps Dropping?

Mar 28, 2012

We have a home network which consists of one Motorola wireless router and 3 PCs. Two of the PCs connect directly to the wireless router without any issues, however, my PC dosent have a built in Wi Fi card so am using a TP Link wireless N USB adaptor.... so as you can imagine the signal is still very poor. So I have bought a TP Link AP and have it set up in repeater mode to increase the range of the router and thus improve my connection.

Now this works great in the short term as I get full signal, but the problem is the signal tends to drop out every 20 mins or so.Now, originally we were recieving an IP address conflict message which I thought was causing these drop outs, but I have rectified this by using MAC address filtering on the AP (think the AP was connecting to someone elses PC in our block of flats), but the drop outs still continue.

I have a static IP set on both my PC and AP and DHCP enabled on the Motorola router, I have also tried changing the Motorola's channel and moving the AP to different places but the story dosent change.I am a right noob when it comes to networking and have got this far by reading manuals, google searching and trail and error so dont know what else to do.

View 6 Replies View Related

Huawei EC159 Usb Modem Compatible With Asus Router RT-N56U

Dec 17, 2012

I wanted to know whether Huawei EC159 usb modem is compatible with ASUS router RT-N56U as I want to be sure before going for it..!

View 3 Replies View Related

Cisco Routers :: SRP500 Compatible With Huawei E398 USB LTE Modem

Jul 15, 2011

is the SRP541W compatible with the Huawei E398 USB LTE Modem? If not, will it be compatible in the near future?

View 4 Replies View Related

Can WRT54GS Repeater Use Antenna For Incoming Signal

Mar 6, 2013

I have a wifi signal set up in my home but my studio 200m away gets no signal. I bought a repeater on ebay but it's still too far to pick up the signal. I can't place the repeater between the two structures due to lack of an electrical outlet. If I get an antenna for the repeater (Linksys WRT54GS with W-DRT installed) do I simply attach it where the existing antennas are on the Linksys repeater or is it more complicated than that? It seems to me those antenna ports are for sending a signal not receiving a signal.

View 2 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3220 Doesn't Support Huawei E392 4G Modem

Dec 31, 2012

Region : Finland
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 rel.577775n
ISP : saunalahti

dosen't support my huawei E392 4G modem. if possible would you make bin for this. there is not other modems that you can get for 4G connections from the service provider so it would be nice if there was more compatibility than some old ancient modems. starts to feel like this is been sold as 4G router and dosen't actually support that at all.

View 1 Replies View Related

Put D-Link DIR-615 C1 In Repeater Mode?

Oct 5, 2012

I just recently upgraded my home router from a 615 to a 655, so I thought I would use the old router as a repeater bridge at another location.

I read that the DD-WRT firmware offered a repeater bridge function, so I successfully flashed the 615 C1 with the latest release 7/12.

I get all of the configuration steps, and even have set up client bridge mode. My problem is when I bring down the list of available wireless modes, repeater bridge isn't on the list.

Is the C1 version not able to do this? is there something else I need to do to enable a repeater bridge?

View 4 Replies View Related

Using Repeater To Extend Signal Of Access Point Both TP-Link TL-WA901ND?

Jan 9, 2012

Im in abit of trouble trying to setup a wireless network. Part of the problem is that I am many miles away and I've never setup a wifi-netork involving more than one device, that device being a router.I connected the TL-WA901ND to the router(a Thomson tg787) located in the house, this router couldn't be used simply because the SSID and its password is locked, and we sometimes have people renting the bottom floor and we would prefer a better SSID and a changable password for the network. The first TL-WA901ND(will call this one TL1(AP) from now on, the other being TL2(RP)) is set to operate as Access Point, having a different SSID and password for the network, and it works great. However, when I try to set the other one, TL2(RP) to repeater mode, with the TL1(AP) and that SSID/MAC as "target", it doesn't seem to work. I've tried using bot the repeater mode and the universal repeater mode but none of them seem to do the job.Is is possible to repeat the signal of an access point or does it have to be a router? The SSID and the WPAkey of the repeater is set to the same as the access point, is that correct?The access point is not the one handing out IP-addresses, the router is still acting as the DHCP-server, is that correct?

View 1 Replies View Related

Linksys Won't Connect In Repeater Mode?

Jan 13, 2013

i have a linksys running dd-wrt and i had for a long time and it always worked but recently it just stopped connecting.i dont know how to fix this it would always say connection limited.

View 2 Replies View Related

Siemens Gigaset Repeater Wlan Se365 Boosting Wifi Signal?

Mar 7, 2013

I recently purchased a Wi-Fi repeater (Siemens Gigaset Repeater WLAN SE365) to boost my wi-fi signal throughout my house without having to drill through walls of concrete (with a boost in phone wi-fi in mind on the top floor of the house). I was advised to buy one specifically with the make and model of my router in mind, as connectivity might be an issue if these don't match up. I own a Siemens Gigaset SX55 router so there should be no issue there (I can use the repeater on 2 different frequencies, not sure which one is best, 2.4 or 5 ghz). The instruction manual told me to connect the repeater to my pc once (through use of an Ethernet-cable supplied) so I could alter the settings of the repeater to match with that of my router (same SSID, protection method, channel). Whereas naming it the same as the router by modifying the SSID and using the same ASCII WEP-protection password as the router were doable, I could not find an option to change a channel.

At this point the instruction manual was fresh out of ideas and told me that I had set up the repeater as it should be installed. After unplugging it from my pc and plugging the regular ethernet cable back in for internet (There is wi-fi coming from the router downstairs but also a cable through the house to the pc) I was ready to go and seeing the wi-fi bars on my phone jump up to maximum made me extremely happy. Unfortunately the phone (and the app Wifi Analyzer) did recognize the full signal but when trying to open sites or apps that use internet it responded as if it had no signal whatsoever

View 3 Replies View Related

Linksys Routers - Using BEFW11S4v4 As Bridge Or Repeater To Send Wireless Signal

Jan 4, 2012

If I have two Linksys wireless routers in my house, ( 1 Wireless-G as the Gateway attached to the DSL line, and attached to the main computer, and 1 Wireless-b model BEFW11S4v4 that I want to use as a bridge or as a repeater to send the wireless signal around the attic (2 floors away) and I have connected them via Ethernet, and then connected to the attic computer (not the main one) via Ethernet to Wireless-B, why can I not get connectivity on the attic computer?

If I forgo the Wireless-B router, and connect the ethernet to the attic computer everything is fine, but there is no wireless signal in the attic. (only downstairs where the Wireless-G is.) I believe I can access the Wireless-G and tell it to be a bridge or a repeter (?? I think) but as far as I can tell the Wireless-B is giving itself the same IP address as the Gateway Wireless-G is using, and I don't have an connectivity, so I can't change it! Im confused.

View 1 Replies View Related

Cisco Routers :: Setting Up WAP4410N As Repeater To Extend Signal Of E2500?

Apr 18, 2012

Im having problems with setting up my cisco WAP4410N as a repeater to extend the signal of cisco E2500.It works fine when there is no password to be set on both devices. But when either one of these devices had beenset a password on it, then WAP4410N failed to extend the signal of E2500.
 
I tried steps as below:
 
1. Same password type in WAP4410N and E2500.

2. Different password type in WAP4410N and E2500.

3. Set password in WAP4410N ONLY.

4. Set password in E2500 ONLY.
 
All steps above makes WAP4410N fail to extend the signal range of E2500. WAP4410N successfully works as a repeater to extend the signal of E2500 when there is no password to be set on both devices.

View 2 Replies View Related

Cisco Wireless :: Does AP1142N Have Any Repeater Mode

Apr 12, 2012

We have an 2504 wireless controller at the office with 5 LAP1142's.  At another office we have a single AP1142 which doesn’t quite reach end to end.  Ideally I want drop in another AP1142 to provide end to end coverage.  Does AP1142 has a repeater mode?  If not is there any way to make two AP1142's work with each other so they appear as a singular access point?  Can they be configured to handle roaming?

View 1 Replies View Related

Cisco Wireless :: 1142 In Repeater Mode?

Jun 2, 2012

I am a bit confused of the repeater functionality in the mentione AP, my concerns are:
 
1- Will each radio be dedicated to one function (for example 2.4 GHz for user access and 5.0 GHz for repeater functionality)?

2- Will the internet speed for users be affected when using the access point in repeater mode (no ethernet)?

3- Can an Autonomous AP function as a repeater?

4- Is there any license required?

5- What is the signal overlap requirements between the two Wired and non Wired AP?

6- Can the non wired AP be work as a repeater for another non wired AP (similar to cascading)?

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved