TPLink TL WR741ND - Router Setup With USB Modem?

Dec 26, 2012

I've got a a tp-link TL-WR741ND, but I don't have a ADSL2+MODEM ROUTER, (ADLS MODEM). Instead I've got a orange usb modem, how can I install the device?

View 2 Replies


ADVERTISEMENT

Linksys Wireless Router :: How To Setup TPLink / TD-W8101G With Cisco E2500

Jan 15, 2012

I have IBM X3200 M3 ( with onboard 2 LAN ) not connected into internet,tplink modem router + wireless ( ADSL MODEM )--->cisco E2500---->ibm x3200 m3( ubuntu )

View 8 Replies View Related

TP-Link 150Mbps- TL-WR741ND - Getting Proper Setup Assistant Software?

Feb 24, 2013

Region : China
Model : TL-WR741ND
Hardware Version : V4
Firmware Version :
ISP :

My router box and the router itself are listed as 741N. I find no reference in the forums or on the website to this model. During setup, I can ping the router from the cmd prompt, but then it fails during the Easy-Setup assistant. I need to use the Easy setup because the language is otherwise Chinese, but it fails the network test. One of the two messages it sends are "Check the Model number". Is this a possibility? Is there a work around or where can I find the proper Setup Assistant software?

View 3 Replies View Related

Configure Tplink Modem On Repeater Mode In Order To Repeat Signal From (Huawei)?

Dec 4, 2011

That's y topology:

(TPLINK) /////////////// (Huawei)--->(internet)
...................wirless................cable

I want to configure my tplink modem on a repeater mode in order to repeat the signal from (Huawei) ...

View 1 Replies View Related

Unable To Use Tp Link Tl-wr741nd Wireless Router?

Dec 14, 2011

we just recently upgraded our router from an old model of d-link to tp link's tl-wr741nd. the wireless router was set up fine. but we noticed that we now experienced disconnection problems. our internet would just disconnect and then connect again every 5 minutes or so. but when i check the modem everything's fine. lights are on. even the lights on the modem are on. this problem never happened on our old router. is this possibly because of the N technology our new router has?

View 13 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR741ND / IPhone 5 Recognizes Router But Will Not Connect

Dec 11, 2012

Model : TL-WR741ND
Hardware Version : V1
Firmware Version :
ISP : EOLO

give me procedure for connecting WiFi to iPhone.The phone recognizes the router, but will not connect.No numbers, i.e. 192.168.1.1, etc are loaded No DNS loaded?

View 2 Replies View Related

Setup Router With Usb Modem?

Jan 19, 2011

I brought a router TP-LINK TL-WR741ND . I have an usb modem which has no other port as lan . I have only one ethernet lan controller which is integrated .Now With the mentioned device above can i setup my router , so i can use the internet on other wifi device.

View 2 Replies View Related

TPLink - Cannot Connect To Router Or Internet

Nov 13, 2012

I have a TP-Link wireless router which we have always been able to connect to the router with these laptops. My sister has come over to use our internet, which has worked before on her laptop, but now all of a sudden she can't connect to our router, it won't even allow her to type in the password it just says Windows can't connect to the network. I then tried one of our other laptop and after much battling it also refuses to connect to the router. eventually it did, but it still can't connect to the internet.I sat on the phone for about a hour with our network provider (I am from South Africa), and after trying many things, it still won't work. The guy said that there is nothing more to try.

[code]....

View 14 Replies View Related

TL-WR542G - Tplink Router Became Unresponsive?

Jun 18, 2012

So I am an owner of this router for the last 2 years: TL-WR542G - Welcome to TP-LINK . Today it died on me. All of its leds are lightning up, but it doesn't provide a wifi network, and won't give me an interface when i try to access it through 192.168.1.1 on my desktop . There seems to be nothing I can do about it , I tried pushing the reset button on it's back but it does nothing at all.

Do I have any other options to get some life back into it?

View 1 Replies View Related

Switches :: Setup A Server Behind Dsl Modem And Router?

Sep 22, 2011

I want to setup SQL Server on my internal home network, and make it available to my colleagues.

[code]...

Win 2008 Server with SQL Server.What do I need to do to allow my colleagues to connect to the SQL server from their computers, in their offices (not on my network)?For example, because I have a DHCP address from my ISP, do I need to use something like DynDNS to track my IP address?

View 1 Replies View Related

Three Computers - Internet Modem And Router Setup

Jul 14, 2011

We have three laptops in our house. We are set up with internet that gives me a direct connect and up to eight wireless devices. My son and daughter-in-law use the wireless and I use the direct connect. M son added a router (which I have no idea what that does) and set up networking on his computer (which I also have no idea what that does). When I am the only one on the computer, it flys. When either of them get on thiers too, it slowes a little. When both of them get on, I might as well get off because it can take up to three and a half minutes to load a page.

View 3 Replies View Related

Modem Router Access Point Setup?

May 15, 2012

I bought the DIR 655 to put into our network as the Netopia wireless fails to connect even though we have maximum signal strength. Att advised that buying a third party router would solve this problem.I did manage to almost configure the DIR 655. I would have to connect it to the system to test it[CODE]

View 5 Replies View Related

How To Disable Router In Cable Modem Setup

Jun 13, 2011

I've been having problems with the router portion of my cable modem router. I have a brand new router that I would like to use rather than the crappy router that is part of the cable modem.The problem is that I'm not able to get online no matter how I set the settings. I have disabled DHCP in the cable modem router and am connecting this to the router thru the internet port of the router.

View 12 Replies View Related

TPlink Router - Unable To Access Internet

Jul 23, 2012

I am able to connect to TPlink router through my pc but unable to access internet.The router is unable to detect dynamic ip.

View 1 Replies View Related

TPLink TLWR941N - Remote Desktop Behind A Router

Mar 20, 2012

I looked at portforward.com and have forwarded port 3389 in the modem with the ip address set to the router's address. I've also forwarded 3389 in the router to the pc's address.

View 14 Replies View Related

Connect To An Already Installed TPLink Router With Security?

Apr 30, 2011

I have a TP Link router installed at home with a 128 Bit encryption key. I have my home laptop and a couple of I-touches that are able to connect wirelessly. I have a laptop from work that I have not been able to connect to the TP Link after inputting the encryption key. how to be able to connect without affecting my home units that are already working?

View 3 Replies View Related

Linksys Wireless Router :: E3200 Setup Using USB Modem?

Apr 25, 2012

How do I setup a E3200 router using a wireless USB modem to connect to the internet? This is my only choice, I do not have a wired connection and I do not own the telephone wires and there is no permission to do otherwise.

View 3 Replies View Related

Linking TPLink As Access Point To DLink Router?

Dec 12, 2011

I want to link a tp link router as access point to a d-link router.

View 2 Replies View Related

Wireless :: TPLink WR1043ND Router - Can't Handle More Than 22 Users

Sep 12, 2011

I have router TP-link WR1043ND which cant handle more than 22 users?

View 4 Replies View Related

Unable To Connect To TPLink Router Wr941nd Through LAN Ports?

Jan 4, 2011

I have tplink router wr941nd. it was working fine but i when tried to use it again after some months i encountered this strange problem in which i am unable to connect to the router through its lan ports where has i can access the router through wlan i have tried reinstalling the firmware i have even installed dd wrt on it but i am unable to access it through the lan port.

View 3 Replies View Related

How To Connect TPLink Adsl With Belkin Wireless Router

Jan 13, 2013

I hav bsnl broadband connection in my home.... I connected a tplink wired for browsing...I also have a belkin wireless router..... I connected those routers.... And only wired communication is possible

View 7 Replies View Related

Cisco EPC2325 Modem - Router Cannot Connect To Internet During Setup

Jan 12, 2013

I've decided to set up a home network - my first attempt at setting up a network, but have run into a problem;I've bought a Linksys HRT54GL routers and connected it to a Cisco EPC2325 modem. I run the setup wizard and everything is going well until the router tries connecting to the internet when a pop-up appears telling me that it can't connect to the internet and that i should try turning my modem off and on again.

View 1 Replies View Related

Cablenet / Netgear Jnr1010 Wifi Router Setup Without Modem?

Feb 16, 2013

I am having netgear JNR 1010 wifi router and I use Cablenet. the wire which carries internet is directly connected to my Desktop pc's LAN port without modem.Is there any way to install this router without conecting to modem?

View 3 Replies View Related

Setup A Canyon CN-FW514 Wireless Router Through A Thomson Modem

Feb 11, 2011

I'm trying to setup a Canyon CN-FW514 wireless router through a Thomson modem.When I first started trying, I could get up the set-up screen on [URL] however this is as far as I got; the laptop said it had a very strong signal with the wireless connection, but I could not get any web pages to open (windows explorer couldn't detect any problems either). The Thomson modem works when I conect it to the laptop via the ethernet cable, but that's not much use to me trying to use the internet elsewhere in the house!I tried changing the IP address, subnet mask and gateway IP address on the set-up screen [URL] which seems to have been a big mistake; I now can't even get the set-up screen to appear.I've reset the internet options and have set everything to obtain the IP address automatically but am still having no luck.

View 5 Replies View Related

Home Network Setup Using Netgear Wireless Modem / Router?

Feb 2, 2013

I have two netgear wireless modem / router. I want to connect my internet, NAS and Media player on one device (netgear modem/router) and want to link the other netgear in my bedroom and connect another media player and also use the internet via primary netgear modem/router wireless connectivity.

View 1 Replies View Related

Setup Cable Modem / Router With Printer Attached To One Of LAN Ports?

Jan 25, 2012

Im trying to setup a cable modem which is also a router that has a printer attached to one of its lan ports. From there it connects to another router which connects to other clients from there i have another router with a VPN connection with other clients. I would like to be able to see everyone on the network. How do I setup the routers in particular the router with the vpn which is the last router. Also the vpn router is connected through its WAN port to the router ahead of it at its lan port so it can use its VPN connection.If it makes it easier lets ignore the cable modem as router and ill find the printer another way of connecting but essentially i need the two other routers for two ip addresses. One for the first router with my regular IP and then the other is for VPN IP.

View 3 Replies View Related

Linksys Wireless Router :: E2000 Setup Near Modem In A Room

Dec 25, 2011

So my family has an E2000 setup near the modem in a room that litterally is a DEADZONE, signal bearly gets in or out of this room. I've argued until I was blue in the face that  we ned to rewire the internets inlet to the house in to another room that isn't a deadzone and rune a router from there.They IT disadvantaged refused. We have also an E2500 they say hook it up, maybe it will work better (when your in a concrete and mettal room with a router sitting on a shelf surrounded by book and with a corless phone system hooks up and sitting on top of it... its jsut not going to work. is there a way i can take the E2500 and make it an access point for the E2000? 
 
I figure if I can I would take the E2500 and put int in a better location and jsut have it relay the E2000 internet. Because of the IT limited thought process of most of the people living here I'd prefer that they share the same SSID or atleast make for a simple transition for the apes I live with.

View 6 Replies View Related

ASUS RT-N65R Wireless Router - 3G Modem Sharing Setup?

Jan 29, 2013

I have an Asus RT-N65R wireless router, When setting up the 3g USB modem, it asks for the ISP. The ISP isn't listed.

View 1 Replies View Related

Protocols / Routing :: TPLink TP-8840 Router Led Blinking And No Internet

Jan 13, 2013

I had this problem for 3 months now, at random times I get no connection and the LAN led 1 in my router (which I am connected to) just keep blinking very fast, ADSL and ACT leds are just on. I tried to troubleshoot the problem and it detected 2 problems: "default gateway is not available" and "local area connection doesn't have a valid IP". even when it says that it is fixed, seconds later the problem is still there (sometimes it gives me one problem only). I tried many solution on the forum including reseting the router, disabling the laptop's wireless modem (I'm on a laptop) and even trying ipconfig/release - ipconfig/renew. everything is up to date and I update my antivirus (and it has auto update enabled). here are my specs:

Broadband connection: DSL
Router Make/Model: TP-LINK TP-8840
Anti-virus: Avira free anti-virus
ipconfig data:

[Code].....

View 19 Replies View Related

Using Tplink Tl-wa5110g Wisp Client Mode With Wireless Router?

Jan 2, 2013

I have a WISP internet connection. i have a Acess point tplink tl-wa5110g . i set it to wisp client router... My final goal is to share my wisp internet wirelesly.

Now i want to ask what i have to do next. do i need wireless router and connect it with the Ethernet port of the acess point..

View 1 Replies View Related

Motorola Modem / Router For Desktop To Setup Wifi For Kindle Fire?

Dec 27, 2011

I am trying to get my parents Kindle Fire to work. They recently purchased a Motorola Modem/Router which is hooked into the desktop and works fine. I want to get their new kindle to work and can not seem to figure it out. Their operating system is Vista which I can upgrade to Windows 7 if that would make it easier. When I click on setup the WiFi part of the installation wizard cd that came with the Motorola it says there is not a network adapter. I know what that is however I do not know why I would need it when the desktop is hooked directly into modem/router and I just need the WiFi for Kindle.

View 12 Replies View Related

Linksys Wireless Router :: E4200 Accessing Modem Setup Page?

Dec 4, 2011

if it is possible to access a modem setup page with a E4200 router? My router is on 192.168.254.200 and modem(WAG-200G) is on 192.168.254.100, ethernet cable is on internet port on the e4200 and on port1 on the modem. Modem is set is bridge and I set up a ppoe and dhcp on router. Everything is ok, except that i can not access modem setup page to see adsl conection speed and settings.

View 1 Replies View Related

Cisco Wireless :: Setup To 2921 Router Connected To Cable Modem

Apr 21, 2013

I have one interface setup to a Cisco 2921 router connected to a Cable modem.DHCP is on the 2921.when I connect to the ssid for my guest i'm redirected to the authentification portal 1.1.1.1 .i'm putting valide credential and when pressing the submit button .. it just go anywhere.
 
I have setup another SSID with a psk and it's working fine.. getting ip and able to browse internet.From what i have read... it's apparently DNS issue on my router.. but what should I check.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved