Cisco WAN :: Address Translation Logging ASR1006
Nov 12, 2011I would like to know if Cisco Collector Engine 6.0 can recive and reading the sent address traslation logging of router ASR1006. Using Netflow v9.
View 4 Replies
ADVERTISEMENT
Cisco Switching/Routing :: NAT Translation Netflow V9 - Router ASR1006
Nov 10, 2011I have problems in exporting translations of NAT from my router through NetFlow v9 ASR1006, to my server nfdump, any opensource or licensed software (collector) that I recommend.
ip nat log translations flow-export v9 udp destination 10.1.1.15 1181
D-Link DIR-655 :: Set Up IP Address Translation
Oct 18, 2011I have 5 static public IP addresses assigned by my ISP. I like to use one of these static public IP addresses to access one of my PCs in my office from the outside. So I like to configure something like:65.11.22.44 <-> 192.168.1.100.This translation is good for all protocols and all ports. Where I can configure this on the DIR655?
View 2 Replies View RelatedCisco :: Network Address Translation On 6500?
Nov 22, 2012We've got an application that is running on our LAN that is using IP addressing to connect to the server (they refused to use DNS).The server is now being moved to a VM which will be on a different subnet. The supplier is now concerned that there will be a big down time due to him having to reconfigure each device (about 100) with the new server IP. If the server was external I know I'd be able to do NAT on the FW to make this work but can it be done internally on my 6500s? I want to have the devices pointing at their hardcoded IP address off 1.1.1.10 and NAT the destination to the VMware servers IP 2.2.2.10? Is this possible using cisco NAT?
View 13 Replies View RelatedCisco Firewall :: ASA 8.4 With NAT Source Address Translation?
Dec 5, 2012I have a server in a DMZ of my 8.4 ASA with nat:
object network FTP-SERVER
host 192.168.1.102
nat (dmz,outside) static interface tcp ftp ftp
And that's working well. However, I now need to translate the source address of connections from the outside to the FTP server as well. The aim is that the source address of packets when they reach the FTP server is an address on the DMZ subnet (as the default route for the FTP server now needs to be something else, not the ASA) as well as this outside-dmz NAT. I thought overloading the DMZ interface of the ASA? Or another IP in that range?
How Network Address Translation Works
Apr 18, 2011How Stuff Works "How Network Address Translation Works"."This is where NAT (RFC 1631) comes to the rescue. Network Address Translation allows a single device, such as a router, to act as an agent between the Internet (or "public network") and a local (or "private") network. This means that only a single, unique IP address is required to represent an entire group of computers." so let's say 6-7 pc's can have access to the internet using the same IP. doesn't this causes any problems? what if one of those pc's was used fore doing something illegal? how can they spot it later on? or what if 2 or more pc's access (from that subnetwork) access the same website with the same IP?
View 3 Replies View RelatedCisco Firewall :: ASA 5520 Address Translation And Port Forwarding
Oct 31, 2011I am trying to correctly configure our ASA 5520 and our Mitel Border Gateway in our DMZ. In the documentation for the Mitel border gateway it wants me to set up 2 external IP's on my ASA one to allow 443 traffice into the MBG, and another for 443 traffic that needs to be forwarded to port 4443 for the MGB in the DMZ. My problem is I don't know how to do this. the MBG only has one IP, and I need to have 2 different URL's mapped to two different external IP's both externally using port 443, and one of them forwarding to 4443 on the DMZ interface.
View 10 Replies View RelatedCisco VPN :: 2911 / Port Address Translation For Remote Network?
Aug 4, 2012I have site to site vpn between cisco asa and cisco 2911 router.asa is static ip and cisco 2911 side is dynamic ip. my site to site vpn is working fine. I am just trying to make PAT over the vpn means i want forward one ip in my public pool to one of my local ip in the cisco 2911 side.
View 2 Replies View RelatedCisco Firewall :: ASA 5510 Address Translation Through Internal Network
Jan 19, 2013Is it possible to perform static Nat's through an internal network?I have a ASA 5510 with a public outside interface (let’s call it 68.68.68.1), and I have an inside private IP address (192.168.1.2/24). The inside IP address leads to a 4900m with that interface being configured with a 192.168.1.1 (no switching). On the 4900 M I have several VLANs one of them is an internal DMZ of sorts. (192.168.2.0/24). Within this DMZ network are several Web servers which need to be associated a public IP address (68.68.68.x).
Every time I configure a static Nat to associating a public IP address with an internal IP address within the DMZ, packet Tracer on the ASA informs me that the packet gets dropped at the static Nat and I cannot figure out why this is so.Safe it to say my question still stands is it possible to Nat (68.68.68.222 to and 92.168.2.60) given the configuration above, and how would I go about configuring in such the manner above so that I acn apply static nat through the 192.168.1.0 network to reach the 192.168.2.0 network.
Cisco Firewall :: ASA 8.3(2) / PAT Interface Address With Static NAT Port Translation?
Aug 22, 2011I have an 8.3(2) ASA with a single outside IP. Dynamic PAT translates inside addresses to the outside interface address. I would like to use static NAT with port translation to access an inside syslog server. I got an error when I tried using the outside interface address. Can I use both dynamic PAT and Port Translation with the same outside address?This is what I would like to use but I receive an error saying there is an overlap using the outside interface address.(192.168.1.0 is my inside network. 10.10.1.10 is the outside interface IP.)
object network inside-net
subnet 192.168.1.0 255.255.255.0
nat (inside, outside) dynamic interface
object network SYSLOG_SERVER
host 192.168.1.50
nat (inside,outside) static 10.10.1.10 service tcp ssh ssh
Home Network :: Static Port Address Translation?
Mar 24, 2011In my router I can set rule that all traffic incoming to router's extAddr:8888, is forwarded to my intAddr:8888. But I also need reverse rule that packets originating from intAddr:8888 are translated to extAddr:8888. Can I do that? What technique can I search on google to find more information, because it is not port forwarding. I would calll it reverse port forwarding or static port address translation, but I do not find anything useful in internet searching these keywords.
View 3 Replies View RelatedCisco Application :: ACE 4710 Source Ip Address In Logging
Mar 21, 2013I've configured the ACE4710 to bring the logging to a syslog server! Here's the configuration
[...]
logging enable
logging fastpath
[Code]....
I saw to log with connection on the syslog server but It would be interesting to know the "source ip address" and my question is : It may be possible to configure for the logging a kind of "transparent pass through"?
Cisco Firewall :: ASA 5520 - ASDM Logging - Disable Rules Logging
Nov 16, 2011I'm encountering what I think is an issue on logging system on FW ASA 5520 - Asa Version 8.4(2), ASDM version 6.4(5). When I disabled the logging inside a rule from ASDM, or from console with the "log disable" option inside ACL, If I check in ASDM logging real time window I continue to see all the entry related to disabled rules. This is a correct behaviour about ASA logging ? How I can "hide" the entry related to disabled rules (this is what I need for troubleshooting purposes) ?
View 1 Replies View RelatedCisco WAN :: ASR1006 Log NAT Translations
Feb 24, 2013We have:
ASR1000-RP2
ASR1000-ESP40
ASR1000-SIP40
SPA-10X1GE-V2
SPA-10X1GE-V2
!
Kiwi Syslog Server
ASR performs the function of ISG. The number of subscribers until 10000. This number is constantly growing. Because of the economic address space subscribers surf the Internet through NAT.
Now the task to keep logs of all translations or binds. Need to store the information about what time, certain internal IP address using the external IP.
I've tried:
!
ip nat log translations syslog
!
logging trap debugging
logging host xx.xx.xx.xx transport UDP port xxx
no logging console (so as not to load the CPU)
!
Error stopped publishing but logs do not come. I think of the huge number of translation per second, it can not send them as fast. How can this problem be solved or otherwise obtain and store information about a translations?
Cisco WAN :: Show Modules In ASR1006?
Feb 15, 2012In a 6500 or 7600 a 'show module' gives a run down on all the modules in the slots, their HW and SW versions and status. But I can't find a similar command in the ASR1006.
View 1 Replies View RelatedCisco VPN :: Configuring DMVPN With 2 ASR1006 Routers
Jun 7, 2011 I'm trying to configure and DMVPN architecture with two routers ASR1006 to server a bank remote offices, one ASR in CO building and the other in CA building (CO: Operational Center; CA: Recovery Center).Each ASR have two LAN connections to internal network and two WAN links to remote office. Each WAN links belongs to differents provider.Each remote office has a router with two WAN links connected to that WAN providers.We are configuring the DMVPN considering two primary tunnels in the CO building and two failover tunnels in CA building.We made the configuration (schemas and configuration attached) but we only get two tunnels up at a time. We cannot ping from office router to four tunnels interfaces in both hubs.
We made some test disabling some tunnels and we could get communication only with two tunnels interfaces. We got communication through tunnels when we have just two.We want to have the four tunnels for high availability. We would like to know how to troubleshoot and make a design review because the examples and documentations are very limited.
Cisco WAN :: ASR1006 Restarts When Write Command
Jan 8, 2011my ASR1006 router with the IOS ver:
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISE-M), Version 12.2(33)XNE, RELEASE SOFTWARE (fc1)
is restarting again and again when I try to write the configuration.
Cisco WAN :: ASR1006 / Traffic Drops When BGP Re-converges
May 5, 2011why I would see packet loss when BGP comes back up.We have 2 ASR1006's both running full tables of BGP to the same upstream ISP. We load balance the 2 links to them. the ASR's have an OSPF connection between them.When one pipe goes down we see not packet loss; however, when that pipe comes back up we see packet loss until the BGP table fully loads in that router again.
View 1 Replies View RelatedCisco :: Show IP SLA History Empty - ASR1006
Aug 29, 2012I want to do something with IP SLA and started by estabilishing a baseline.
I'm trying to check history on an ASR. I tested same config on a 3845 and was forgetting the "history filter all". After this I could see history table on 3845 but still history is empty on the ASR1006. The operation started because I can see information with "show ip sla statistics".
know if i missed something or maybe this is not supported in ASR1006?
re-ld-tcc-02_ASR1006#show vers
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-ADVIPSERVICESK9-M), Version 15.2(1)S2, RELEASE SOFTWARE (fc1)
[Code]......
Cisco WAN :: ASR1006 - Keeping Logs Of All Translations Or Binds
Jan 4, 2011ASR performs the function of ISG. The number of subscribers until 10000. This number is constantly growing.Because of the economic address space subscribers surf the Internet through NAT.Now the task to keep logs of all translations or binds. Need to store the information about what time, certain internal IP address using the external IP.
View 19 Replies View RelatedCisco :: ASR1006 - Discovering Netflow Aggregation Cache
Sep 28, 2011We have an ASR1006 and I'm just discovering net flow aggregation cache.
I tried prefix aggregation and worked fine. But i cant get any information when checking AS aggregation. All I get is 0 in source and destionation AS. [code]
Cisco WAN :: ASR1006 - Create PPPOE Connection Via Ethernet?
Jan 10, 2011I have cisco router ASR 1006 .... i need to create PPPOE connection via Ethernet ... and can do that on the management port ???? and what is the type of adapter that use in the Giga Ethernt interface to connect it to fiber ???? hint :- my interface hardware SPA-10X1GE-V2
View 7 Replies View RelatedCisco WAN :: Configure ERSPAN On ASR1006 - Not Getting Any Traffic On Destination Port?
Mar 18, 2012When trying to configure ERSPAN on a ASR1006, I'm not getting any traffic on the destination port. ERSPAN flavour is LOCAL SPAN, as described in:
[URL]
Configuration used, is the following:
monitor session 1 type erspan-source
no shut
source interface GigabitEthernet0/0/2
destination
erspan-id 10
ip address 10.10.10.1
[code].....
Apparently everything is configured in the proper way, however I’m not getting any traffic in the destination port. Also I’ve noticed the following in the details from ‘Session 1’:
Destination IP Address : 10.10.10.1
how to configure Local SPAN using ERSPAN?
Cisco Wireless :: ASR1006 L4 Redirect CaptivePortal-DHCP Radius Attributes
Dec 3, 2012There is an ASR1006 Router in the network that serves as an Intelligent Service Gateway (ISG). Subscribers are layer 2 connected and subscriber sessions are initiated on a DHCP request. ISG is configured as a DHCP relay agent. Wi-Fi clients connect to the WLAN using Open SSID and are being redirected to a Web Portal where they enter their login info. This info is sent to RADIUS server which checks if the user is allowed to use Internet service. All the APs are connected o WLC using CAPWAP. The question is the following: there is a requirement to track from which AP a particular Wi-Fi clients is connected. In this case ISG needs somehow to obtain AP’s mac address and send it to the Radius server (probably using attribute 30 – Called-station-id). One possible way for ISG to obtain AP’s mac is via WLC. But the thing is that when WLC is configured as DHCP proxy and Option 82 is set, a wireless client does not obtain IP address via DHCP. In this particular case there two DHCP relay/proxy in the network path between client and DHCP server. Is there any other away for ISG to obtain AP’s mac address?
View 8 Replies View RelatedCisco WAN :: 881 Router - NAT Outside Translation
Jun 16, 2011currently I face problem with outside nat translation and Im not sure how to solve it. I gotta 881 router
int vlan1
ip address 10.10.10.1 255.255.255.0
ip nat inside
[code]...
and remote server 100.100.100.25 routed to interface fa0/0. So the problem is that hosts from V lan 1 and V lan 2 want to communicate to this server, but they cannot route, which means, that I have to "give" them some IP from their range as fake address of this server and translate it. So I did
ip nat outside source static 100.100.100.25 10.10.10.7 (for Vlan 1)
ip nat outside source static 100.100.100.25 20.20.20.7 (for Vlan 2)
but I get
% 100.100.100.25 already mapped (10.10.10.7 -> 100.100.100.25)
As far as I understand router doesn't allow this translation, because if the communication would be started from outside (initial packet would come from server side), router wouldn't know how to translate its source address.
Cisco Firewall :: ASA 5520 Nat Translation Max?
Aug 24, 2012I am going with ASA 5520, know how many NAT translation is possible.
View 2 Replies View RelatedCisco VPN :: ASA 7.2(2) - No Translation Group Found?
Aug 1, 2010My remote VPN clients aren't able to do anything network wise once they have connected to the VPN. The ASA keeps coming up with "no translation group found" in the log.
Result of the command: "show running"
: Saved:ASA Version 7.2(2) !hostname ciscoasadomain-name office.propertyfinder.comenable password ######## encryptednamesdns-guard!interface GigabitEthernet0/0 description Office Network Interface nameif Office-LAN security-level 100 ip address 10.121.10.4 255.255.255.0 ospf cost 10!interface GigabitEthernet0/1 description 4Mbps BTNet Internet Connection nameif Internet-Primary security-level 0 ip address 213.121.253.33 255.255.255.248 ospf cost 10!interface GigabitEthernet0/2 shutdown no nameif no security-level no ip address!interface GigabitEthernet0/3 description Office Wireless Interface nameif Office-Wireless security-level 10 ip address 172.16.0.1 255.255.255.0 ospf cost 10!interface Management0/0 nameif management security-level 100 ip address 192.168.1.1 255.255.255.0 ospf cost 10 management-only!passwd 2KFQnbNIdI.2KYOU encryptedboot system disk0:/asa722-k8.binftp mode passivedns domain-lookup Office-LANdns server-group DefaultDNS name-server 10.121.10.20 name-server 10.121.10.21 domain-name
[code]....
Cisco :: 881 / SNMP Number Of NAT Translation
Jan 5, 2012I am looking for the SNMP OID to monitor the sh ip nat translations on a cisco 881.
#sh ver
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Thu 26-Feb-09 06:01 by prod_rel_team
[code]....
Cisco VPN :: DNS Payload Translation In VPN3000?
Apr 8, 2012We have a VPN configuration currently using a VPN3000 device. According to this [URL] and some others I seen DNS payload can also be translated in NAT configuration.How can I doing it with the VPN3000 box ? On my configuration DNS payload aren't translated, but it is maybe an option I need to set or unset !
View 1 Replies View RelatedCisco WAN :: 2801 Route-map For Static NAT Translation
Dec 6, 2010I have a nat and vpn setup on my Cisco 2801 router.Everything is working as expected except the NAT. I have a single static nat translation but it only works for inbound and not outbound. Going outbound, it uses the default overload nat address of the outside interface. [code] I want to add another mailserver. But I fear if one mailserver were to get black-listed, they would both be reporting there ip address as the same address (the one on the ethernet interface) which would blacklist both mail servers.Again, inbound nat works ok, but outbound is just using the IP of the ethernet0/0 address.
View 2 Replies View RelatedCisco WAN :: 3620 - Change Source IP Of IP NAT Translation?
Feb 20, 2013Some network pros have setup our Cisco 3620 many years back during implementation.
I've just added a new server, with new ip, wanted to change the ip of ip nat translation in this router.
I did a show run, the config is this;
interface FastEthernet0/0
ip address 57.31.132.116 255.255.255.240
no ip redirects
[Code]......
Cisco AAA/Identity/Nac :: ACS 5.1 Error Code Translation
Jun 17, 2010I upgraded an ACS4.2 to ACS5.1, and in the ACS View Dashboard „ACS – System Errors” I see the following error message: [code] Unfortunately I can't find any documentation what describe what ERROR codes mean, so I don't know what does 32603 ERROR code mean.
View 11 Replies View RelatedCisco VPN :: ASA 5505 Anyconnect Language Translation
Apr 26, 2012I'm having a problem with the language translation for anyconnect.here's my setup:
-asa 5505
-asa version: 8.4(3)
-asdm version 6.4(7)
-anyconnect essentials
-anyconnect webdeploy: anyconnect-win-3.0.5080-k9.pkg
The anyconnect client is deployed by the asa using the webdeploy.my client machine is a windows 7 with regionnal settings set to french (canada).I added the language localization transform files for web deploy (the mst for french) to my asa using the asdm:remote access VPN -> network (client) Access -> anyconnect customization/localization -> Localized Installer Transforms -> add the french mst.