Cisco VPN :: Show Crypto Session Dumps Different Between 2811 And 2901 Routers
Nov 28, 2012
I have installed a new 2901 router with the IOS version 15 code (c2900-universalk9-mz.SPA.152-3.T.bin). I have a template config that I have created for my remote VPN routers that I have been using on 2811 routers with version 12.4 (c2800nm-advipservicesk9-mz.124-24.T1.bin).I do have the securityk9 active on the 2901 software
Technology Package License Information for Module:'c2900'
-----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc None None None
data None None None
Issue is when I do a "show crypto session" the GRE tunnels session status read down on the 2901 router but on the 2811 session reads up-active. Everything is working and I am routing over the GRE Tunnels.
[Code] ......
View 1 Replies
ADVERTISEMENT
Nov 24, 2012
i repalced old cisco router 2811 with new one 2921 , all works except crypto map VPNs routers can ping each other , ACLs are not applied to outbound interfaces show crypto isakmp sa is empty after i make same configuration on a new router 2921 config crypto isakmp policy 10
hash md5
authentication pre-share
crypto isakmp key key address Y.Y.Y.Y no-xauth
[code]...
keys match , crypto isakmp policy is same , IOSs supoort VPN .interess traffic alse been initiated from both side and all worker in old cisco router with same configuration?
View 3 Replies
View Related
Jan 13, 2013
I have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
View 6 Replies
View Related
Aug 18, 2011
In a basic VPN l2l scenario using ezVPN, server behind NAT device, client using 3G. What would be the reason to have in the output of the show crypto ipsec sa, a current peer different from remote crypto endpoint on the server ?
View 3 Replies
View Related
Feb 25, 2012
I have setup ipsec VPN in my C2811 router but when "show crypto isakmp/ipsec sa" shows nothing. Remote end point is an "ASA5520". Does it indicates that the remote ASA5520 not yet configured?
Code...
View 9 Replies
View Related
Nov 16, 2011
I replaced old cisco router 2811 with new one 2921 , all works except crypto map VPNs routers can ping each other , ACLs are not applied to outbound interfaces show crypto isakmp sa is empty after i make same configuration on a new router 2921 config.
View 1 Replies
View Related
Jul 15, 2012
My router is Cisco 2811 with IOS version 12.4(22)T1. It had established IPSec with another peer (203.*.*.250 shown below) for long until recently we make it re-establish IPSec VPN with another peer (203.*.*.30 shown below). It showed that the new sa is active but the result still showed there were 4 deleted SAs. The 4 obsolete sa entries won't vanish no matter what I do i.e. reset the interface, re-create crypto map, clear all sa and etc.
From numerous testings we knew that the VPN doesn't work even the desired sa is there remaining active. I reckon it has something to do with those deleted sas ( i mean it is supposed to show only the last one if it is working fine ). I don't know how it would be come like this as we did pretty much the samething on other VPN routers with no problems.
View 20 Replies
View Related
May 17, 2012
I'm dealing with a 4506 switch that whn I try to apply "sh auth sess int xx" I get "Invalid Input Detected" ... Is there any way that I can get the authenticated session over a port even if I can't apply "sh auth sess int"?
View 1 Replies
View Related
Jan 9, 2012
I have a switch 4948, with version 12.2.31.sga4 ( I dont found bug about monitor session) and we try to made port mirroring with a monitor session from a VLAN and port belong at this VLAN have traffic input and output, but in the destination port, I always see it output traffic..
Global command
Red-127#sh run | in moni
monitor session 1 source vlan 1127
[Code].....
View 3 Replies
View Related
May 4, 2011
I have a Cisco 2811 and a Cisco 1841 and I cannot get these cards to show up. My IOS for the 1841 is c1841-spservicesk9-mz.124-6.T7 and my IOS for the 2811 is c2800nm-spservicesk9-mz.124-17. When I do a "sh diag" the cards come up as: "unknown daughter card WIC module is not supported/disabled in this slot".
So I am guessing I need a different IOS.
View 1 Replies
View Related
Apr 11, 2012
Would it be possible to make a socks proxy (not normal http) which dumps all outgoing connection/packets to a file then can change the file then re-send it?
View 1 Replies
View Related
Dec 5, 2011
I have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies
View Related
Jul 7, 2011
I have to install and configure two 2901 routers at different location with high availability. These 2 routers would be connected through WAN, now I would like to configure high availability bwtween two routers.
I have attached a small diagram of the placement of 2 routers.
how do I configure high availability between these 2 links or routers.
View 3 Replies
View Related
Jun 10, 2013
Does the 2901 have etherchannel capabilities? If so, how to configure it? I mean, I can type "show etherchannel 1" in it, so I would assume if I can show it, I better be able to configure it, right?What about the 2911?
View 1 Replies
View Related
Oct 2, 2012
I have 1941, 2901 ISR routers. I will use 3G backup when primary link (metro ethernet / G.SHDSL) goes down. Do I have to use Data License (SL-19-DATA-K9 / SL-29-DATA-K9) in order to switch back to 3G when primary link is not reachable) ?
View 7 Replies
View Related
Feb 13, 2012
In my company we put a RV042 router to connect two links to internet, but we have problem to enter a bank. The solution they gave us was to disable encrypted session balancing but I don´t know how to do it.
View 2 Replies
View Related
Nov 19, 2012
I'm practicing MPLS and wanna establish a simple LDP targeted session between 2 indirectly connected routers. when establishing this session with loopback IP address of routers, the session is established, but when I tested this session with another router's fast0/0 that is MPLS enabled, the session did not established. I wonder, if a targeted LDP session, needs to be established between 2 IPs that are selected as LDP IDs of respective routers. I made routers to use their fast0/0 IP addresses as LDP ID and the session was established.
View 2 Replies
View Related
Oct 7, 2011
I have two routers 2811, which set ntp client. Different versions of the IOS, other devices are working properly. My routers takes time to ntp with other router,which take time from ntp server.
View 1 Replies
View Related
Mar 6, 2012
I got the Cat-5e network cable but I cant get it to show up, when I plug it in I cant seem to get it to show up on my computers.
View 4 Replies
View Related
May 24, 2011
How come the 2600 series IOS has the show mac-address command but it does not display anything? you need to use show arp? is this for when you use one of those network modules that is a switch?
View 2 Replies
View Related
Mar 13, 2013
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies
View Related
Jan 29, 2012
How to understand "show sessions" and "show connection" commands? And what is the difference between the two?
View 2 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Jun 18, 2011
I have a cisco 1760 with running VIC-2FXO (working fine). I'm now trying to replace that line with an ISDN line through a VIC2-2BRI.
View 4 Replies
View Related
Aug 5, 2012
A multipoint GRE (mGRE) and IPSec tunnel is built between two routers. The topology of the device is briefied below:Configuration in End Router: This is a cisco 2811 router. Amoung 2 ethernet interface ,one is using for LAN and one is for WAN. In WAN part , we have configured mGRE (Tunnel1 and Tunnel 2)by creating sub-interface of the router. From the interface ,we terminating the link to MPLS cloud from there its pointing towards our core router.From End router we are advertising the path through EIGRP and from the cloud BGP advertisied to the core router.[code]
View 1 Replies
View Related
Oct 18, 2012
What are the IPv6 anycast addresses using for?, are they some kind of broadcast? I have a router 2811 I'm configuring ipv6, do I need to use these addresses?
View 1 Replies
View Related
Mar 22, 2012
why does my 2811 routers boot to rommon after uploadig IOS c2800nm-ipbasek9-mz.151-4.M1.bin
View 1 Replies
View Related
Mar 24, 2011
ipconfig /all reports one of my three DNS servers as 192.168.1.1. My Default Gateway and DHCP Server are also reported as 192.168.1.1. This is from a recently installed Valet M10 updating an old Linksys router. The Linksys reported the three DNS servers octets independent of the router's ip and other default settings.JK
View 1 Replies
View Related
Feb 6, 2012
Why does err 0x80040900 show up sometimes when tx/rx email? I use a WRT54GS linksys router. I have more than one computer which use Microsoft Outlook 2003 to check email accounts. When the error shows up I can ping the server no problem. The error sometimes goes away and comes back randomly.
View 2 Replies
View Related
Feb 16, 2013
I purchased a new BelkinN750 DB router on 2/12/2013. It seems to think the date is Jan. 1 1970. How can i fix this problem or should I just return it and buy another brand?
View 2 Replies
View Related
Sep 18, 2011
Basically the problem that I have is that I have a new Exchange server sitting on 192.168.12.2 IP address and on the router I have this NAT enabled
ip nat inside source static tcp 192.168.12.2 110 212.115.5.5 110 extendable ip nat inside source static tcp 192.168.12.2 25 212.115.5.5 25 extendable
The Exchange can receieve emails but it will not send them. It cannot make connection to any of the smart hosts on port 25 or can't even send mail using DNS. When I run telnet my.smarthost.com 25 it will not connect but if I run that from the router then it connects fine.
View 1 Replies
View Related
Jun 17, 2012
I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
View 5 Replies
View Related
Mar 7, 2011
I have this situation, I need to establish an IP sec communication to another site but I need to identify all my packets sent, as a different networks as my local one. for example: my local network is 10.5.0.0/24 and I need to sent packets as 10.6.0.0/24. I suppose that I need to do Nat with this IPs. But in this router Nat is already applied to outbound traffic to Internet. How can I apply this NAT to crypto map only?
My router is a Cisco 877 with 12.4 IOS an this is the relevant configuration, crypto map vpn it´s used to sent traffic to second site.
crypto isakmp policy 2 encr 3des authentication pre-share group 2crypto isakmp key xxxxxxxxx address XX.XX.XX.XX
crypto ipsec transform-set vpn esp-3des esp-sha-hmac
crypto map vpn 1 ipsec-isakmp set peer XX.XX.XX.XX
[ code]....
View 2 Replies
View Related
