I have two routers 2811, which set ntp client. Different versions of the IOS, other devices are working properly. My routers takes time to ntp with other router,which take time from ntp server.
View 1 Replies
I faced up with a strange configuration issue at my 2811 router running IOS C2800NM-ADVIPSERVICESK9-M, Version 15.1(3)T. The configured Dynamic and Static NAT do not work (users can't go out to Internet and can't reach internal services via external IPs).The configuration seems to be very simple (one internal and one external interface, one address for dynamic NAT pool, and only few static translations -- see attached file).
View 8 Replies View RelatedWill NME-AIR-WLC6-K9 work in Cisco 2811 Router?
View 3 Replies View RelatedMy router is Cisco 2811 with IOS version 12.4(22)T1. It had established IPSec with another peer (203.*.*.250 shown below) for long until recently we make it re-establish IPSec VPN with another peer (203.*.*.30 shown below). It showed that the new sa is active but the result still showed there were 4 deleted SAs. The 4 obsolete sa entries won't vanish no matter what I do i.e. reset the interface, re-create crypto map, clear all sa and etc.
From numerous testings we knew that the VPN doesn't work even the desired sa is there remaining active. I reckon it has something to do with those deleted sas ( i mean it is supposed to show only the last one if it is working fine ). I don't know how it would be come like this as we did pretty much the samething on other VPN routers with no problems.
I'm trying to connect a Cisco 2811 using an octal cable to a Juniper MX480 console port.Since the distance between Cisco 2811 and router is 20ft, im using couplers and a straight-through cable for the lack of slack. This wiring doesnt work, however in another city it works going straight from the Cisco 2811 octal cable to the router since they are in the same rack.
View 4 Replies View RelatedA multipoint GRE (mGRE) and IPSec tunnel is built between two routers. The topology of the device is briefied below:Configuration in End Router: This is a cisco 2811 router. Amoung 2 ethernet interface ,one is using for LAN and one is for WAN. In WAN part , we have configured mGRE (Tunnel1 and Tunnel 2)by creating sub-interface of the router. From the interface ,we terminating the link to MPLS cloud from there its pointing towards our core router.From End router we are advertising the path through EIGRP and from the cloud BGP advertisied to the core router.[code]
View 1 Replies View RelatedWhat are the IPv6 anycast addresses using for?, are they some kind of broadcast? I have a router 2811 I'm configuring ipv6, do I need to use these addresses?
View 1 Replies View Relatedwhy does my 2811 routers boot to rommon after uploadig IOS c2800nm-ipbasek9-mz.151-4.M1.bin
View 1 Replies View RelatedBasically the problem that I have is that I have a new Exchange server sitting on 192.168.12.2 IP address and on the router I have this NAT enabled
ip nat inside source static tcp 192.168.12.2 110 212.115.5.5 110 extendable ip nat inside source static tcp 192.168.12.2 25 212.115.5.5 25 extendable
The Exchange can receieve emails but it will not send them. It cannot make connection to any of the smart hosts on port 25 or can't even send mail using DNS. When I run telnet my.smarthost.com 25 it will not connect but if I run that from the router then it connects fine.
I have installed a new 2901 router with the IOS version 15 code (c2900-universalk9-mz.SPA.152-3.T.bin). I have a template config that I have created for my remote VPN routers that I have been using on 2811 routers with version 12.4 (c2800nm-advipservicesk9-mz.124-24.T1.bin).I do have the securityk9 active on the 2901 software
Technology Package License Information for Module:'c2900'
-----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc None None None
data None None None
Issue is when I do a "show crypto session" the GRE tunnels session status read down on the 2901 router but on the 2811 session reads up-active. Everything is working and I am routing over the GRE Tunnels.
[Code] ......
I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
I have 2 Cisco routers , 1841 and 2811 , I need to setup site to site VPN , but i dont now some how it just does not seems to be working ,
Find attached the Configuration along with the
<----- 172.31.1.0/24----- DG:172.31.1.1>Cisco 2811<Dialer1 -----//Internet//----------Dialer1>Cisco1841---< DG:10.236.5.254-------------- 10.236.5.0/24--->
Find attached command executed on each router in the below order
1) show ver
2) Show run
3) show logging
4) show crypto ipsec sa
5) show crypto isakmp sa
Debugging enabled on routers are
1)Debug Crypto Isakmp
2) Debug Crypto Ipsec.
I've never had this problem before with my ISP (Knology).But supposedly they had a scheduled maintenance real early this morning before 6 AM.Well, ever sense they did maintenance the router will not work and neither will my old one. The new router is a netgear, the old one is a linksys.I called them a few times and everything they had me try did not fix the problem.I can get internet access connected directly to the modem just can't get the router to work.When I right click and diagnose the problem it tells me that it's a connectivity issue with the modem. When I use my old linksys router and diagnose the problem it tells me that the DNS server is not responding.I have also tried resetting the new and old routers to default settings and started fresh.
View 16 Replies View RelatedI have an RV180 VPN router.I try to enable the VPN users with PPTP or QuickVPN but is not working.For PPTP sometimes my windows 7 connects to the router, sometimes doesn't connect with a random error message.When it connects, the windows 7 from outside the lan can see the computers from inside the lan but the computers from inside the lan cannot see the windows7 one. This is random also. When i succed to connect, from that computer, the internet is not working anymore.I tried to set the VPN in the same subnet as lan, i tried with different subnet. Is not working.I updated the last firmware. The same.Restore factory settings couple of times, the same.
View 6 Replies View RelatedI have problem with bandwidth management on my RVS4000.
That is the way how i done it:
All traffic (TCP & UDP on all ports)
IP range 192.168.0.2 - 192.168.0.2 (My IP adress)
Guaranted download speed 1kbps
Maximum download speed 5000kbps
after saving setting and rebooting router I have maximum download speed on my PC 12000kbps, Why QOS doesnt work ?
Rx:, recently I have perchase 2 RV120W routers thinking that it must be very easy to setup the site to site vpn. i cannot get my remore office to link to my main office and vice verser.
Scenaro
- I'm using 2 RV120W routers for each site.
- Site A using a subnet of 192.168.10.0 mask 255.255.255.0
- Site B using a subnet of 192.168.11.0 mask 255.255.255.0
I have setup the VPN using the wizard and I got site to site tunnels connected and show as 1/1 Connected (1 user) in the status he IPsec connection status show
--Policy Name: VPNA
--Endpoint : public IP address from my ISP 203.117.222.221
--Packets Tx:145 Rx:0 and Kbytes shows Tx: 29.55 Rx:0
Q1 why I cannot use dynamic DNS naming in the policy setting ? eg: aaa.dyndns.org, I have to use the ip address instead eg: 203.117.222.221
Q2. I cannot connect from Site A to Site B , I can't even do a ping to 192.168.11.1 from Site A. even though it show the Site to site tunnel is coonected.
I am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies View RelatedWould one of the 'Cisco RV016' work with a switch? I'm planning on running our work network using this device to load balance between 3 WAN connections and would like to keep the upstairs and downstairs computer users separated via a switch.Will the switch affect the load balancing or will the router still be able to detect each individual user and balance the load as seen necessary?
View 7 Replies View RelatedI have a big problem with my cisco wrv210. I want to use URL Filtering to block facebook.
Enable
ip range : 192.168.2.5-192.168.2.254
url string : Facebook, www.facebook.com , facebook.com notting work.
Apple AirPlay won't work on AppleTV (from neither computer nor iPhone) with my new Cisco small busines router WRVS4400N. It was working just fine on old consumer level linksys router. I have spent 3 hours with Apple support to no avail. Apple TV works fine on internet functions (netflix, YouTube, etc.) and I can play music and videos from the cloud, but iPhone and computer can't connect to AppleTV even though the icons appear in iPhone and Computer... just can't establish a connection.
View 2 Replies View RelatedToday i have a Linux computer as a router and it works fine, but when i change to my RV042 the software VPN stops to work (VPN Direçáo) on the computer. We use this software VPN for the card payments (D-TEF) so i have to get it to work. I opened the same ports as i had in the Linux on the RV042 did not work, i opened all port on the RV042 did not work, i put it in DMZ mode and it did not work, i opened it all to the IP address of the computer that has the program on it. The computer with the VPN software has a fixed IP adress.
View 7 Replies View RelatedTried everything .... beginning with updating to actual firmware, installing C++Redistr and all other tips I found.eg there are no ssldrv.* in the assumed directories .... there is a certificate which is outdated in the 1920th (lol) ... it´s true.Phone support is not avail .... because we use it a couple of years .... with xp and vista there is no prob?Perhaps there is a usefull handout/whitepaper available? I´ve followed this link, but that did not work:[URL]
View 1 Replies View RelatedI have been unable to get the UPnP function to operate on this router. Box has been checked and saved several times with no results. Ports cannot be opened maunally as well. I have been through every page looking for something that was missed, along with the sparse documentation instructions to no avail.
UPnP and port forwarding worked fine on the residental E3000 router that this replaced. I thought this was an upgrade, but it is seeming like a downgrade now.
connect my new device and get it working as an extender?
View 2 Replies View RelatedI have a Linksys Cisco system router and cannot get it to work, I believe I have it hooked up right. I am wanting it for a Sylvania wireless mobile internet device.
View 1 Replies View RelatedI'm trying to ensure I have wireless coverage in my entire house and having extreme difficulty getting all machines to play nicelyWireless modem router #1 (downstairs in my house) is connected to the ADSL line and has the following config:IP Address = 192.168.1.1 DHCP on DHCP pool 192.168.1.3-192.168.1.100 Subnet = 255.255.255.0 Wifi channel = 1 Wireless router #2 (upstairs) is connected by ethernet cable to Wireless modem router #1 and has the following config:IP Address = 192.168.1.2 DHCP off Subnet = 255.255.255.0 Wifi channel = 11 Different SSID and encryption key to Wireless modem router #1 With this configuration, I can connect to the internet via both routers and all seems to be well. Except... having established a connection through either one, my machines will only make a pretend connection with the other one. By "pretend", I mean that the (Windows) machine says it has an excellent connection to the router but can only see machines on the LAN - it cannot get to the internet even though other machines are connected through the same router to the internet.
For example, if I'm sitting next to the downstairs router and establish a connection with it, all is well. Then I move upstairs and my machine switches to the upstairs router. Signal strength will be reported as "Excellent" and I'll be able to connect to the local NAS or printer but no external devices or sites.I have tried having the same SSID and wireless configuration on both but the result was the same.Today I read the suggestion to enable the DHCP server on the 2nd router but to set it to distribute a different non-overlapping IP range (i.e. router 1 can have a pool of 192.168.1.3-192.168.1.50, and router 2 can have a pool of 192.168.1.51-192.168.1.99)
i want to set WRVS4400N Route all traffic through, it function as same as sonicwall Route All.
View 1 Replies View RelatedToday i installed an RV180 VPN router as replacement for a netscreen ns-5GT.Exactly the same configuration, everything works, except port forwarding from WAN to a host inside NAT.My ports are open (online port-scanner sees the ports as open), the hosts are accepting connections, but a connection can't be made.Probably a bug in the firmware.
View 30 Replies View RelatedHow to set this new router up correctly in a way that they can get open nat with one Xbox on the network?I have tried to setup the router so that I port forward the following ports:
UDP/TCP | 3074
TCP | 80
TCP | 88
UDP/TCP | 53
The xbox is setup with a static ip address:
IP | 10.141.167.50
Subnet Mask | 255.255.255.128
Gateway | 10.141.167.1
In addition to simple port forwarding, I setup access rules in the firewall with any source to go to the 10.141.167.50 single ip destination. I have also tried with port forwarding off, but upnp on, and the ports setup specifically in that screen for this xbox. Finally, I disabled the port forwardingin the upnp, as well as the port forwarding screen and simply setup port triggering, while leaving the upnp service enabled. After all of that, the xbox would not get open nat. It doesn't make any sense to me that this doesn't work. I even tried turning off all port forwding and triggering and putting the xbox in as the dmz host. No dice. I'm honestly thinking now that there is a problem in the firmware or something that requires some special workarounds. I'm on the new firmware (i.e. 4.1.0.2) and at the end of my rope.
Using an rvs4000 with firmware v2.0.3.2 I am able to delete 'setup/lan/static ip mapping' entries, but I am unable to add any.After deleting an entry, hitting save (which reboots the router) and then trying to enter the same device with a different static ip address, the "add" button has no effect.
View 2 Replies View Related1) SG200-18 configuration
- VLAN 10 and 20
- VLAN 10: Port 1 tagged, Port 14 untagged
- VLAN 20: Port 1 tagged, Port 13 untagged
- Port 1: 1UP, 10T, 20T Admit tagged PVID 1
- Port 14: 10UP Admit untagged PVID 10
- Port 13: 20UP Admit untagged PVID 20
Port 1 connected to Fiber ONT (On VLAN 10), Port 14 connected to RV042G WAN.Once RV042G LAN connects to SG200-18 (VLAN 1) port, RV042G WAN unable to get public IP and internet connection gone, port 14 showing "Discarding" under "Spanning Tree"
I have configured the sr520 using cca.Basically I have a device connected to the sr 520 via wireless with the ip address 192.168.200.160.
The SR connects to the internet using adsl and pppoe.I configured NAT to the device for a number of ports, however it doesnt work.
I have a problem with my RV110W router. I would like to setup Quick VPN access. Manual is quite straightforward: enable management, create users, install client and that's all, should be working. But NOT. it does not work.
Remote Management is enabled on port 8080. Should it be changed to 443 as required for QVPN? Or it does not matter. Is it ok, to have management on 8080 and QVPN on 443?
I have tried to connect via QVPN Client ver. 1.4.1.2. Of course ip as well as user and pass has been changed. I tried to change management port to 443, but first:
1. i was not able to access management console at all
2. QVPN - still did not work
