Cisco Routers :: RV042 V3 And XBox 360 / Can't Get Open NAT To Work
Dec 14, 2011
How to set this new router up correctly in a way that they can get open nat with one Xbox on the network?I have tried to setup the router so that I port forward the following ports:
UDP/TCP | 3074
TCP | 80
TCP | 88
UDP/TCP | 53
The xbox is setup with a static ip address:
IP | 10.141.167.50
Subnet Mask | 255.255.255.128
Gateway | 10.141.167.1
In addition to simple port forwarding, I setup access rules in the firewall with any source to go to the 10.141.167.50 single ip destination. I have also tried with port forwarding off, but upnp on, and the ports setup specifically in that screen for this xbox. Finally, I disabled the port forwardingin the upnp, as well as the port forwarding screen and simply setup port triggering, while leaving the upnp service enabled. After all of that, the xbox would not get open nat. It doesn't make any sense to me that this doesn't work. I even tried turning off all port forwding and triggering and putting the xbox in as the dmz host. No dice. I'm honestly thinking now that there is a problem in the firmware or something that requires some special workarounds. I'm on the new firmware (i.e. 4.1.0.2) and at the end of my rope.
View 2 Replies
ADVERTISEMENT
Jan 17, 2012
I have a RV042 Dual Wan. Two internets balanced wow! who would've thought that the headaches were waiting patiently right down the corner.
I was working with a 2wire Gateway that came with my ISP. I was able to open the ports in order to have public access for my students and teachers to upload their work. All I had to do was to allow my server ip address to have access to different ports blocked by the ISP. I used [URL]
I bought the RV042 for various reasons like excellent content blocking, load balancing, quick vpn, among other. But I just can't open the port 80 while having having my two ISP connected with load balancing, not even while having only one modem connected.
I have resolved many issues using the protocol binding. I have tried everthing. I just don't undertand something.
Whenever I connect my server to my old router, "www.canyouseeme.org" tells me that my port 80 is open. Whenever I connect my servet to the RV042-DW, my port appears closed.
So it's not any OS issues.
I've tried:
- To forward the TCP 80~80 port to my server static ip address... but failed
- To enable UPnP function with the same port... but failed
- To configure the port triggering with the same port.. but failed.
- To disable the firewall.. but failed.
- To use transparent bridge in the WAN1 with my 2wire Gateway... but failed
- To set up an account in DNS.ORG already had one, everythings is in green.. but failed.
- To change the configuration in my old 2Wire Gateway router to allow a DMZ zone so all ports are public... but failed.
- To assign RV042 router ip address in my old 2Wire allowing that specific address to allow certain ports to be public... but failed.
I have the Firmware v4.0.4.02 from DEC/11
[URL]
View 2 Replies
View Related
Dec 12, 2011
I have been trying for about a week to get open nat on my three xbox 360's I have in my home. Things came to a head last week when the gaming group and I tried to play over xbox live, but our games kept disconnecting. When I checked my network, none of my xboxes had open nat.
I had only one public ip at the time we had the trouble, but now I have 5 public ip's from comcast. Currently, I only have one of them setup with my router working as normal.
On that router, I have given the two xboxes static ips:
10.141.167.50
10.141.167.51
One of the xboxes is setup with port forwarding with the following ports:
3074 UDP/TCP
88 TCP
80 TCP
53 UDP/TCP
the other xbox is setup as a dmz host. The xbox that is setup with port forwarding gets open nat, but the other one, despite being the dmz host, does not get open nat.
The router is setup as follows:
10.141.167.1 - router ip
10.141.167.2-149 - dhcp server range
255.255.255.0 - subnet mask
My dns servers are from open dns. I have only one wan connection coming into the router also. That is through comcast business class. The connection is a 30/5mbps connection. One last thing, I have the latest firmware on the router as well. I updated it last thursday evening 12/8/2011.
View 2 Replies
View Related
Dec 31, 2012
How to change my NAT type from moderate to open for xbox 360. Belkin n450 dual band
View 1 Replies
View Related
Jan 2, 2012
Is there a way to use QuickVPN with the RV042 without leaving ports 80 and 443 wide open to Shields UP! scans? As a workaround, I am forwarding these ports to a non-existent IP and forcing QuickVPN to use port 60443. Yes, 60443 shows as open too if I scan it, but at least it's not in the first 1056 ports.
Router is Linksys-branded, using latest firmware for this hardware (1.3.13.02-tm)
View 5 Replies
View Related
May 23, 2012
I have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies
View Related
Apr 18, 2012
A company with 20 branches in Rio de Janeiro area. The main servers are in a datacenter located in downtown.Each branch has a RV042 router with firmware version 1.3.12.19-tm (Feb 13 2009 13:03:21) installed.All users in this network have a proxy configuration pointing to proxy.[blah].com.br port 3128.the HTTP/HTTPS traffic should go through proxy only. [code] Some "smart" users were caught using Ultrasurf application, which changes the proxy settings to go through port 9666 or even 443.In other machines, we've found some black proxies [for example: 212.46.27.142 port 8080].
My objective:
- To close all ports in Firewall -> Access Rules section and grant permission only to some selected and specified ports.
- To redirect all HTTP/HTTPS connections to go to proxy's IP address only.
Which Access Rules can I set in these RV042s in order to block and prevent these users to continue abusing this network?The users who were caught using Ultrasurf were fired.
View 3 Replies
View Related
Jun 15, 2011
Today i have a Linux computer as a router and it works fine, but when i change to my RV042 the software VPN stops to work (VPN Direçáo) on the computer. We use this software VPN for the card payments (D-TEF) so i have to get it to work. I opened the same ports as i had in the Linux on the RV042 did not work, i opened all port on the RV042 did not work, i put it in DMZ mode and it did not work, i opened it all to the IP address of the computer that has the program on it. The computer with the VPN software has a fixed IP adress.
View 7 Replies
View Related
May 7, 2012
I have activated Protectlink Web. But today i started to get "router is busy" in all pages, so we restarted the router. That problem was solved but now the the web Protection is no longer working. It says activated but licence status says waiting.
View 1 Replies
View Related
Sep 22, 2011
I have tried to load the config file from an RV082 to an RV042 with no luck.Is there a way to convert the RV082 file to work in a RV042?
View 3 Replies
View Related
Jul 25, 2012
I want to make a question about RV042. I used RV042 router in my office. I used content filter feature in router.Althought this have not been apply the rules. I think I made wrong rules.I enabled the block enable forbbiden domain .And then added the websites that I want block.However, these websites are still browsing in local computer.
View 4 Replies
View Related
Jun 15, 2012
Will the RV042 work with theAnyConnect Secure Mobility Client app? If so, is there and app note available? If not, which routers wil work with this app?
View 5 Replies
View Related
Nov 7, 2007
I have a WRT54G ver.5.(just did latest firmware) and a Buffalo Air Station wireless gaming adaptor.I have gone and port fowarded the UDP 88,UDP 3074,TDP 3074 I believe I have left the UPnP on (brother in law says not an issue)(?) On my XBOX 360 i have the IP & DNS set to Auto, and I get an OPEN setting on my NAT.But when I play online (Halo 3) I can't join any of my friends' parties,acting like it is STRICT. When I set up my IP & DNS to Manual and put in static IP & DNS, I run the tests and get STRICT. It seems to me that even though my NAT "says" its OPEN, it is really on STRICT.
View 4 Replies
View Related
Dec 15, 2010
i have the xbox and ps3 wired to the router and the laptop wirelessly to the router (if that makes any difference)
My router is the Linksys WAG54G2
View 9 Replies
View Related
Jan 28, 2011
I got a new Xbox 360 Slim and he has it connected through wireless, and His older Xbox 360 connected through Ethernet. And well we would like to play some games online without some major lag. So is it possible to have an Open NAT with two Xbox's within the same network?He has a Linksys Wireless-N Broadband Router WRT160Nv3.
View 5 Replies
View Related
Feb 17, 2012
I have a E1000 and already for the longest time I've been trying basically everything possible to get my NAT open from being strict.I've looked around and tried everything I came across including the port forwarding. The only thing different from what I have and from what I have seen is that my router's ip is 192.168.0.1 instead of 192.168.1.1 that everyone else seems to have. I don't know if that affects my NAT in any certain way either. What I can possbily do or what might be the problem as to why I can't get my NAT opened?
View 1 Replies
View Related
Jul 2, 2011
I have tried opening the ports on xboxs website. tried dmz. tried both. i have a basic understanding of changing your xboxs ip.i have disabled windows firewalls and got rid of macafee altogether.
View 10 Replies
View Related
Aug 13, 2012
I'm using Cisco Connect Cloud to connect to my E4200 router. I wish to open my NAT type as currently its moderate on all games.Where the hell is the area to add the port ranges?? Is it even an option on the new connect cloud? If it is, it doesn't make it very easy to find. Would be allot easier if you had a tab/app for "Gaming/Applications" like you did previously.
View 1 Replies
View Related
Apr 7, 2011
how to open my NAT Type For my xbox.
View 3 Replies
View Related
Nov 24, 2011
I have three xbox 360s (mine plus my son and my daughter)...I have my settings set to where when myself and my son are on our 360s our NAT type is open..
View 2 Replies
View Related
Apr 24, 2010
I just recently upgraded my router from the WRT160n V3 to the E3000. I had to port forward from my old 160n to get my NAT settings from Xbox Live set to OPEN. When I switched out the router to the new E3000, my Xbox Live settings went back to Medium (Moderate). I assumed this would happend since its a new router/setup.
setup my E3000 and Xbox Live so I can have my NAT settings to OPEN? I only need to setup 1 Xbox.
View 9 Replies
View Related
Nov 16, 2011
I Have a WRT160Nv2 and I am trying to get my nat to become unstrict for xbox live. I have tried port fowarding that has not worked. I tried this site [URL] and that didnt work(I only have one xbox 360 btw). Nothing has worked for me and every time I mess with something it screws up the internet so I have to set it up to the previous defaults. I know how to access my router I just need to know what to enable, disable, or add to the router.
View 1 Replies
View Related
May 5, 2011
I just got an Xbox and live and tried to connect to my Bell Turbo Hub but it came up with a not enough MTU error, I called Bell and they said It wouldnt work with live. If there is some way to make it work?
View 3 Replies
View Related
Jan 7, 2011
Seems like there those saying they have gotten there DIR-655 and XBOX 360 Wireless N Adpater to work in 802.11n mode. The adapter will only connect in 802.11g mode (and yes I have the correct adapter). I have set the settings to following
802.11 Mode: Mixed 802.11n and 802.11g
Wireless Channel 2.462 ghz - Ch 11
Transmission Rate Best
Channel Width 20/40
WPA-Personal
WPA2 Only
Cipher Type: AES
Does this router really work with XBOX 360 Wirelss N Adapater. If so, how has others got this to work.
View 3 Replies
View Related
Oct 4, 2011
My netgear router kept dropping my internet connection so after some research I bought the DIR-655 router. It installed fine. My computer connects to the internet great and so does my xbox. But now my xbox doesn't see my PC so I can not set up a media center connection. I know it isn't a firewall setting or a setting on my computer because it worked fine with my old netgear router and the router I had before that. I even double checked by turning off the firewall. I have version 2.0 firmware and the settings are out of the box. I assume there is something I need to set up to get this to work but I have not been able to find any answers on the internet. I don't know a lot about networking as I've always used out of the box settings and had success with everything working the way I like.
View 6 Replies
View Related
May 25, 2012
Had to uninstall pure networks software as wouldnt work with new HP printer software 8600 at all. took me 2 days to figure that out. anyways I am a newbie when comes to networking. I finally got everything to work but I cant get the xbox to connect. I tried within the software at the IP address but nothing happens, DWA 552, Software version A2, Firmwre ve 1.1 os/ win xp media 2005.sp 3 computer: made by me: Intel BX97520J (bad axe) cpu: Intel quad, 6600 2.4 ghz,
View 1 Replies
View Related
Aug 1, 2012
I cannot get my xbox to be able wrt54g . Device on comp does not read xbox yet xbox piccks up router
View 4 Replies
View Related
Nov 21, 2012
Continued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
View 1 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Nov 14, 2011
I am having a NAT issue with my two xboxes. The router is an e1000 v2.1 firmware 2.1.02. One xbox is wired into the router and the other has a wireless adapter. The wireless xbox gets open nat automatically, while the wired one's nat is strict. If i mess with DMZ and turn UPnP off i can get the wired to be open but the wireless one to be strict. Also port forwarding does not seem to work because only one or the other xboxes will get an open NAT. I do have the the correct ports in the port triggering section set to on but that does not seem like it works.
View 5 Replies
View Related
Mar 21, 2013
I have the N600DB Wireless Router I am connected to the internet, but cannot open My Routers Homepage with http://router or http://192.168.2.1. How can I get to this page to reset the router settings? I also cannot connect any of my wireless devices to the network..
View 1 Replies
View Related
Jan 23, 2011
Trying to set up Black Ops for the xbox 360 and it wants us to enter a WEP number. Where is this located?
View 1 Replies
View Related
