Cisco Infrastructure :: HWIC-2FE Fails To Pass Ping Packets Greater Than 449 In Slots 0 Or 1
Apr 9, 2013
When we install an HWIC-2FE card in slot 0 or slot 1 of a 3845, the interface fails to pass any ping packet greater in size than 449 bytes. It works fine up until that limit is reached, but then fails completely on a larger size packet. If we move to slot 3 or slot 4 on the 3845, the card works just fine! I have looked through the cisco official bug tracker for HWIC-2FE, but could not find a similar symptom listed. We're running advanced ip services 12.4(24)T7 code on the routers. Any software fix or if this is a platform problem with the 3800 series.
View 3 Replies
ADVERTISEMENT
Jun 13, 2013
Is it possible to pass 802.3 packets over a L2TP?If so, how would the tunnel differ from a normal L2TP?
View 1 Replies
View Related
May 30, 2013
I have a sg200-18 connected via one of the ports to my ISP's router/modem. Using an unmanaged switch everything works as expected, but after a few days on my sg200 my two computers fail to get assigned IP's and cannot connect to anything. I also have a couple printers that seem to have no problems getting their IP's passed through to the router as I can use them fine from my machines when connected to the unmanaged switch.
Is there a possibility I don't have my switch setup properly to know that all outgoing data must go to the router, or UDP traffic is being dropped somehow?
View 7 Replies
View Related
Jan 16, 2008
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
View 4 Replies
View Related
Aug 15, 2011
When I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
View 1 Replies
View Related
Oct 4, 2012
Can We use Cisco HWIC-4ESW as no Switch Port.
View 5 Replies
View Related
Apr 23, 2012
Just want to ask if 4-port serial HWIC-4T is compatible for the Cisco 2801?We need additional HWIC for Fast Ethernet but the problem is we don't have already slot for it.We already have two HWIC-2T 2-port serial which is inserted at slot 1 and slot 3. We're planning to buy 4-port HWIC-4T so we can use the slot 3 for HWIC Fast Ethernet.if it's possible to have the 4-port serial HWIC-4T be inserted to Cisco 2801.
View 1 Replies
View Related
Sep 2, 2011
How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies
View Related
Dec 21, 2010
I would like to passthrough ICMP 8 (ping) requests through the DIR-655 to my server. I found where to allow the router to respond to ICMP 8 requests, however, I do not want the router to responder, rather the server itself. Is there a way to pass these requests through to the server?
View 3 Replies
View Related
Aug 18, 2011
My computer will connect to the home network but won't connect to the internet or pass the ping test.
View 4 Replies
View Related
Dec 28, 2011
I have a 2811 ISR, a lab unit with almost nothing yet configured other than some IP networks on serial and FE interfaces to ping to other lab routers. And I have one HWIC-4ESW installed, and I amrunning IOS 15.2.I want to set the card as a single routable interface and just have the ports act like switch ports, which I imagine is the default design of these cardsI work a lot with Cisco 891 ISRs so figured it's the same here, assign an IP to interface Vlan1 and all is well. That was wrong, obviously more config is required.It seems there are a lot of differing answers out there, so far none what worked for me. The best looking one I could find said to assign an IP to the Vlan 1 interface, then go to each of the four FE interfaces on the switch module.
View 3 Replies
View Related
Apr 17, 2012
I've just started a CCNA course and my lack of knowledge has me a bit stuck. My network is comprised of Cisco components and I'm semi familiar with them just from reading and looking through options. I currently am using a Cisco ASA 5520 on my network and I am trying to join another network via one of the interfaces. My network is 192.168.0.0 255.255.0.0 and my inside interface is 192.168.1.1 255.255.0.0. I enabled a second interface using a static ip of 10.0.0.1 with a subnet of 255.255.255.128. Connected to that interface, I have a Fortigate firewall at 10.0.0.2 255.255.255.128. I can ping just fine from the Fortigate network to the 10.0.0.1 interface on the Cisco ASA 5520 network, but I can not ping the 10.0.0.1 interface (or anything past it) on the ASA 5520 from any computer on the Cisco network. I've read that ACL's and NAT have to be done as well as enabling traffic between interfaces with the same security levels. (both interfaces have security levels of 100 and the option is checked to allow traffic).
Note: each network has it's own internet connection. The connection is to share information on servers on both networks with each other.
View 1 Replies
View Related
Jun 25, 2012
I have a couple of Switches Blade 3120, working as active-standby model (HSRP) on a new site deployment. There are other 20 sites more or less, working on the same model, without issues. But in this one, we are seeing a high cpu usage. The traffic going through the platform is 600Mbps (on peaks), and in this case we have 40% of CPU usage. Traffic should be close to 3 Gbps. When we tried to send the whole traffic through the platform, active switch began to drop packets on the majority of interfaces.
When we analyze the CPU usage, there is a special process called "HL3U bkgrd proce" always have the most CPU use, but we do not know what concerns. We do not know if it is caused because there are PBRs configured. It should not matter. How I mentioned, there are other sites working fine and have had always the same PBR number.
What is causing the high usage?. Is there a special debug we could to perform to diagnose the issue?. Also, we have seen a high interrupt CPU usage (9% in this case).
bog-sib-INT-rtr-1#show processes cpu sorted 5sec
CPU utilization for five seconds: 30%/9%; one minute: 25%; five minutes: 23%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....
View 3 Replies
View Related
Jan 23, 2011
I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan
View 2 Replies
View Related
Jul 3, 2012
I am connecting a cisco device with huawei device. The issue is when i ping with normal size packets (56 bytes) its ok. But when i increase the packet size above 1500 it doesnot works. MTU on both size is configured as 4096. I have also checked by varying MTU size, but still the same.
View 1 Replies
View Related
Oct 23, 2009
I have a new WRVS4400N VPN router and have set it up for VPN. On a separate computer I have a Verizon EVDO card so I have used that with a separate computer to access the internet on a public, routable IP address off of my network.
When I use the QuickVPN client, I wasn't able to get into my network (using ddyns.org) because I didn't have the "BLOCK WAN REQUEST" setting disabled so the router could be ping'd. Once I did that, I verified I could successfuly ping my ddyns name abc.xyz.com.
In the error log of the QuickVPN client, I still see:
2009/10/24 16:57:15 [STATUS]OS Version: Windows XP2009/10/24 16:57:16 [STATUS]Windows Firewall is OFF2009/10/24 16:57:16 [STATUS]One network interface detected with IP address x.x.x.x2009/10/24 16:57:16 [STATUS]Connecting...2009/10/24 16:57:16 [STATUS]Connecting to remote gateway with IP address:x.x.x2009/10/24 16:57:28 [WARNING]Remote gateway wasn't reached...2009/10/24 16:57:36 [STATUS]Remote gateway was reached by https ...2009/10/24 16:57:36 [STATUS]Provisioning...2009/10/24 16:57:47 [STATUS]Tunnel is configured. Ping test is about to start.2009/10/24 16:57:47 [STATUS]Verifying Network...2009/10/24 16:57:51 [WARNING]Failed to ping the LAN IP of the remote VPN Router!2009/10/24 16:57:52 [WARNING]Failed to
[code]....
I HAVE been able to make the connection successfully without any other changes to the environment. It's hit or miss, but usually a miss. Restarting QuickVPN sometimes works on the next try, but then fails if I disconnect and try again. Even when that ping error message is appearing, I am able to ping the host name at a command prompt without a problem.
Is something else on the router possibly blocking the ping requests?My router is behind a Westell F90 6100 DSL modem operating in bridge mode. The 4400 is obtaining the WAN address from Verizon(DSL) and that is also where I have my PPOE info entered to obtain the internet connection.
View 7 Replies
View Related
Apr 9, 2012
I am trying to create a Script to reload my cisco 1941 router when a ping test has failed.I am using IP SLA to ping and tracking snmp oid. What I want to do is to stop the router from reloading after 4 times if the ping test is still failing . But when the ping are successful again to restart the applet. I have the reload configured but cannot figure out how to do the rest. [code]
View 1 Replies
View Related
Dec 29, 2010
We are testing a new 1Gbps WAN circuit between 2 sites. We have cisco 3750 and 4507 on each end. Every time we run extended ping sweep ranging from 36 to 18024 bytes the packets are being dropped randomly once the size goes above 1500 bytes. Our ISP claims Demark to Demark test are clean and they don't want to acknowledge the problem, they blame our switches. To prove the problem is not on our end we've put different switches at each end, still facing the same issue. Ping success rate is around 98 to 99 percent.
View 11 Replies
View Related
Mar 30, 2012
I have a Dell Inspiron 11z (1110) with Dell 1397 mini wireless card. The wireless connection lags/drops persisitently at any time of day or night. When I connect the computer to internet via ethernet the connection is stable. When I run a diagnostics on the wireless card all pass, except the internet IP ping. I get the following message:
The wireless router/AP for your network is working, but your computer is not able to use an IP address to connect to the Internet. You will not be able to connect to the Internet, although you might be able to connect to your local network. Contact your network administrator or wireless router/AP installer for assistance.
I have installed latest driver for the 1397 mini wireless card, albeit a couple of years old.
The wireless router I am using is Netgear Rangemax Dual Band DGND3300v2. I can get into the router administration area but am at a loss as to how to reset/re-install it.
View 1 Replies
View Related
Nov 21, 2011
I have configured a GRE tunnel and set the IP MTU to 1420 then I received this message. %Warning: MTU set 1420 is greater than default 1396, fragments will happen, What and where is this default MTU? Ive never set one and it doesnt look like any values Ive encountered for the MTU before. (its an 1841) Even a link to a document would be fantastic here as I cant find any info so far.
View 3 Replies
View Related
Sep 19, 2012
I have a new technicolor TG582n modem and the wifi signal doesn't reach to all the house. It's a big house, lots of concrete walls. I also have a Linksys WRT54G router and I'm wondering if it's possible to put the Linksys in the other area of the house and capture the signal from the Tompson. Then connect to that signal with my laptop. Maybe this will work to give me wifi in all areas.
View 6 Replies
View Related
Jan 5, 2012
One of our clients is replacing some of their aging network components with 4 Cisco 2960S switches. Unfortunately in this case, my skills of switch configuration are greater than my skills of network design. I have a really crude network diagram of their basic network layout (4 servers, 4 switches, and a number of endpoints).
How would you experts design the physical connections in such a way as to facilitate some redundancy?
View 18 Replies
View Related
Jun 30, 2011
Is there much of a network speed difference between a green drive, Seagate Barracuda or a regular drive?i.e. would you see greater network throughput with a 7200 RPM drive compared to a 5900 RPM drive?
View 6 Replies
View Related
Nov 28, 2011
Can the sup720b be used in any other slot on a 6513 besides 7 and 8?
View 1 Replies
View Related
Aug 20, 2011
I would like to transport two time slots (TDM traffic) over an IP network in order to connect two telecom devices located in different sites, i have cisco 2811 routers on both sites with ip advanced services 12.4.20T IOS
View 5 Replies
View Related
Jan 7, 2013
I want install a wireless card--dual band, N, -- in my Studio XPS 9000 desktop. I have a dual band router.My questions:
1. Are the expansion slots PCI or PCI Express?
2. What card is recommended?
View 1 Replies
View Related
Apr 1, 2013
I have a cisco 6509 (ws-c6509-e) IOS 12.2.(18)SXF6 with the following modules and submodules: [code] I would like to add another module, I have WS-6816-GBIC or WS-6516-GBIC which one will work with my 6509 ? The 6509 has four module slots empty: 4-7-8-9, Can I add the card in one of these slots ?
View 10 Replies
View Related
Jun 27, 2012
I have a situation where a customer doesn't have the required power units installed in their 6500 for me to provision a WiSM2.They use a VSS pair with a single Sup720 in each. They have no intention of adding a second Sup to each chassis.
I need to justify why they can't use slot 6 (which has power reserved) if I am to get them to upgrade the PSU's. The documentation I've found says it is supported but not recommended.
View 1 Replies
View Related
Aug 10, 2010
Is there a way of ascertaining whether my 5510's have 1 memory slot or 4 memory slots without having to open the chassis?
View 6 Replies
View Related
Jun 4, 2011
when I browse for internal WLAN cards for my new desktop their interface is described as "PCI 32 bit", which is weird because expension slots on new desktop mobos are all PCIexpress.I know the PCIexpress's interface is physically different then PCI's, and that it carries 64 bits.So, will that work? Do you know internal cards that with PCIexpress interface?
View 3 Replies
View Related
Sep 2, 2012
My Cisco 2960 Switch hanging problem (does not work or LED light), when i removed SFP module slots its working fine.
View 1 Replies
View Related
Apr 21, 2013
Access Control on an ac1200 does not seem to flexible enough to include hours from say 8pm - 6am. On my old Linksys I would simply have multiple entries for the same MAC address but this does not seem possible.
View 1 Replies
View Related
Mar 12, 2013
Can I populate all 4 EHWIC slots in a Cisco 2911 router with VWIC3-4MFT-T1/E1 cards supporting clear channel T1 data traffic?Or do I need a higher performance router inthe 3900 series to do this?The data sheets lead me to the conclusion that I can but I just want to validate this.
View 6 Replies
View Related
