Cisco Switching/Routing :: 6509 OSPF Neighbor Fails Due To Bad ISA

Mar 26, 2009

our backbone (6509) is connected to atm backbone (nortel passport) those are connected through  giga Ethernet interface and running ospf in area 0. One week ago we lost the ip connectivity between those backbones, the interfaces were in up but the neighbor relation fail and it was kept in LOADING STATE, according  we the logs the neighbor relation fail because a BAD LSA was received (error messages %OSPF-4-ERRRCV:Bad LSU adv and %OSPF-4-BADLSATYPE:Invalid lsa:Bad LSA chksum Type 5 were received during the outage)We check in cisco and this is quite normal behavior if we receive a bad LSA but the customer is asking why we have the same error message for long time and we didn't lost the neighbor relationship.

how many bad lsa we can receive before to lost the neighbor relationship.We receive two errors messages for bag lsa.. [code]

View 3 Replies


ADVERTISEMENT

Cisco Switching/Routing :: IOS For Support Of OSPF And BGP In 6509-E

Sep 13, 2012

If i look at the Feature Navigator , it says that IP Base Supports OSPF and EIGRP. But if i look at the Cisco Link it contradicts the Cisco Feature Navigator.
  
[URL]
 
if I have 6509-E with VSS-SUP720-10G and want to run OSPF and BGP on the Switch. What is the IOS i require? WIll IP Base Suffice or i need to take Advance or Enterprise Image.

View 1 Replies View Related

Cisco WAN :: 3750 OSPF Neighbor Stuck In Exstart

May 5, 2012

We have an existing network with OSPF configured between 3750's (DR and BDR) this is working fine.But the Nexus 7k which has been configured to run OSPF, won't established the adj. It is in the same network/subnet.The MTU is 1500.

View 5 Replies View Related

Cisco WAN :: 3620 - Cannot Issue Ospf Neighbor Command With NBMA Interface

Jul 27, 2006

I config my E0/0 Interface with "ip ospf network non-broadcast" command, I want this interface to use uni cast to hello neighbor.
 
As I issue "neighbor x.x.x.x" under ospf process, it told me that: OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint networks. I am sure that there are no any typo, and show ip ospf interface e0/0 says it's been an NBMA interface, so what's wrong with this router?
 
IOS information:
(C3620-J1S3-M), Version 12.3(18), RELEASE SOFTWARE (fc3)

View 7 Replies View Related

Cisco Switching/Routing :: 3550 / Routing Protocol Neighbor Between SVI And Routed Port?

Apr 18, 2012

I have a collapsed core design with routed ports between all components. Access layer switches, data center switches, core/aggregation. All routed (no spanning-tree at all).Now...I have to add an IBM BladeCenter with a BNT layer 3 switch to my topology. However, those nasties don't seem to support routed ports.How can I have a routed port on my cisco switch and a standard access port on the BNT and still establish an adjacency with an SVI? I am running OSPF, but I am labbing this in my home lab with 2 x 3550s and EIGRP.
 
On SW2:
*Mar  1 00:57:00.711: EIGRP: Received HELLO on Vlan100 nbr 10.1.1.1
*Mar  1 00:57:00.711:   AS 999, Flags 0x0, Seq 0/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
*Mar  1 00:57:02.303: EIGRP: Sending UPDATE on Vlan100 nbr 10.1.1.1, retry 9, RTO 5000 tid 0
*Mar  1 00:57:02.303:   AS 999, Flags 0x1, Seq 17/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1

[code].....

View 10 Replies View Related

Cisco Switching/Routing :: ASR1000rp1 / PIM-SM Neighbor Go Down And Not Coming Up

Jul 21, 2012

I have 2 ASR routers running PIM-SM between them on several sub interfaces.PIM hello interval configured for 200ms.Sometimes PIM neighbors between ASR routers going down.
 
Reboot for each router not resolving the problem.Deleting  ip pim sparse-mode and configuring it again on one of the ASR routers resolves the problem.
 
I didn't find any related bug.The version is asr1000rp1-adventerprisek9.03.06.01.S.152-2.S1.bin

View 6 Replies View Related

Cisco Switching/Routing :: 3750 / EIGRP Router Won't Update Neighbor With New Network

Apr 18, 2012

I am working at a client site today on a routing issue.  I am currently working on an issue where a 3750 switch running EIGRP will not update its neighbor router when a network statement is added to the eigrp instance.The neighbor is a 3825 router.
 
Both the switch and the router have a common network which is 192.168.36.0/24.
Both the switch and the router are in a neighbor adjacency.
Both boxes have "no auto-summ" in the routing configuration instance.
 
I can run debugs on both routers (debug eigrp packets) and then I can watch queries and updates when I issue "auto-summ" or "no auto-summ".  Also I see a "graceful restart" for the peers when this is done.I had an expectation that when I added the network (this is just an arbitrary network for testing, which is 172.16.69.0/24).  I wanted to watch this network being sent in an update to the neighbor router.When I add the above mentioned network, there are no updates packets sent from the 3750 to the 3845.  I have not had success to this point trying to resolve.  I have followed the Cisco document "Troubleshooting EIGRP Flow Chart", but have exhausted all it has to offer and now it is at the point where it is telling me to contact TAC.

View 19 Replies View Related

Cisco Switching/Routing :: 6509 To 6509-E Chassis Upgrade?

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

     x3     48 ports
     x1     NAM
     x2     Sup720
     Running 12.2(18)SXF3
 
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco Switching/Routing :: Upgrade Of 6509 To 6509-E Chassis

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

x3     48 ports
x1     NAM
x2     Sup720

Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco WAN :: 3845 / 6509 - Both Links Via OSPF

Mar 20, 2013

I have one Cisco router 3845 and one switch 6509, they have two links connected each other via OSPF, I want to have link 1 as high priority, and link 2 as low priority. When the link 1 is down, it can be kicked in to the link 2. How I can implement this setup.

View 8 Replies View Related

Cisco WAN :: 6509 OSPF Stays In Route Table

Apr 5, 2012

I have an MPLS router that connects to the core network.This router distributes (per route maps) routes from OSPF into BGP and from BGP into OSPF.The OSPF Process conencts a 6509 to the 7206 MPLS router. There are some routes in the OSPF process that I have filtered out of the 6509. They do not show up inthe 6509 at all and this is the only way they can be getting into the 7206.Checking the 6509 database, this route is gone, but it stays in the 7206 until I clear the route manually. The result is the route still gets distributed into MPLS. [code]

One thing to note, there are two possible OSPF paths the route gets into OSPF, one of them, the route is filtered with distribute-list on the 6509, which means it is still in the database, so it is still in the 7206 database, and still get distributed into BGP on the 7206, correct?

View 3 Replies View Related

Cisco Switching/Routing :: Layer 3 Switching And ASA 5505 With OSPF?

Jun 15, 2012

We are setting up a test lab in our DMZ.  The path to the internet is basically like this.  Anything past the firewall is irrelevant. For this lab lets assume it is vlan 300.
 
LAB SW ---> DMZ-SW ---> ASA FW ---> INTERNET
LAB IP Range = 172.16.300.0 /24
GW = 172.16.300.1 (On FW int)
Trunked all the way through.
 
I have an int vlan set up on the LAB SW.  It is being trunked to DMZ SW.   DMZ trunks it to ASA FW where there is a failover with a redundant switch.On the ASA the interface 0/2 is a subinterface 0/2.300 being used as the default gateway. 
 
I have DHCP running in a specific range on the LAB SW and do get an ip address when plugged in.  I cannot ping the default gateway on the ASA FW.The GW is defined using default-router command for 172.16.300.1 i.e.  default-router 172.16.300.1?
 
We are running ospf on the firewall.  There appears to be a pattern with ospf and a similar subnet setup elsewhere.  I was wondering based off of this info would configuring ospf for 172.16.300.0/24 allow me to ping the GW from a client on the LAB SW.Secondly.  I trunked 300 on the DMZ SW but I didnt add the vlan  to the configuration. i.e.  conf t <enter> vlan 300 <enter>  Does this really matter?  Or is having the vlan in the configuration only pertain to access mode on interfaces?

View 1 Replies View Related

Cisco Switching/Routing :: 4506 Resilient Routing Design With OSPF

Aug 27, 2012

We have 2 sites, each with 2 x 4506 switches which will be connected togther using an etherchannel. The switches will provide access ports for client devices and will be configured with HSRP to provide gateway redundancy. SW1 will be HSRP active.2 metro ethernet links will be installed in each site which will connect back to our HQ sites. OSPF will be used over the backbone to provide resiliency and to allow shortest path routing to each HQ and to prevent traffic over the HQ to HQ link.

The 4506 will be trunked togther with an SVI for providing OSFP adjacency.For the traffic flow from SW2 to HQ2, traffic will hit SW1 and then route back to SW2 and then to HQ2. Is this the best way to do this? Should a second link be connected between switches just for routing or should something like GLBP be used?

View 6 Replies View Related

Cisco Switching/Routing :: Filter A Specific Host(s) From OSPF Routing Table On A ASA 5550 (ABR)?

May 22, 2013

I am attempting to filter a specific host(s) from my OSPF routiing table on a ASA 5550 (ABR) using LSA prefix lists.  However, when I look at the other routers in that area, I notice that ALL LSA type-3's are being removed (10 hosts are now missing from the routing table). I have verified the filter is working on the ABR, but I can't figure why ALL hosts/routes that were coming into the area are now being filtered instead of the specific one that I want to filter out.
 
Here is the config on the ABR:
 
prefix-list pdm_pl_000 seq 10 permit 206.253.180.137/32
!
!            
router ospf 1
network 10.0.0.0 255.255.255.0 area 0
network 10.150.10.0 255.255.255.0 area 10
network 10.150.252.0 255.255.255.224 area 10

[code]....
 
The 206.253.180.137 host is actually coming from Area '3'.  Am I doing something that is removing all type-3 LSA's?

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 7010 / 5510 - Run OSPF As Layer 3 Routing Protocol Between VPC Peer Links

Mar 25, 2012

I have an environment where i have two nexus 7010 switches, along with 2 nexus 5510's. I need to run OSPF as a layer 3 routing protocol between the vpc peer links.  I have 1 link being used as a keep alive link, and 3 other links being used as a VpC link.
 
1) Is it best to configure a separate Vpc VLAN i.e 1010

2) Is it best to configure a vrf context keep-alive

3) just have the management address as the peer ip's.

View 2 Replies View Related

Cisco Switching/Routing :: OSPF Or EIGRP On 851 Or 861?

Dec 14, 2011

Does 800 series routers support OSPF or EIGRP?  Command for EIGRP is available but when you try to run it, you get that "protocol is not available in the image".  Is there a specific image that I can get that will support either of these two on a Cisco 851 or 861?

View 4 Replies View Related

Cisco Switching/Routing :: Does C3560-12PC-S Run OSPF

Nov 21, 2012

I am in a doubt if the 3560-12-PC-S supports OSPF. Datasheet says we need IP Services image. But 3560-12PC doesn’t have the option with IP Services. Then I havigate to [URL] how?
 
So, any clues whether or not this box can run OSPF?

View 1 Replies View Related

Cisco Switching/Routing :: 6500 Migrating L2 To L3 With OSPF In LAN

Feb 4, 2013

We have an existing network with a core 6500 as a VSS connecting 4 buildings with 4500 chassis under which number of L2 switches are connected. Currunlty we are using RSTP in ring for redundancy but we want to use OSPF in LAN for faster conversion.All the VLAN's are created on 6500.

View 4 Replies View Related

Cisco Switching/Routing :: 3560 OSPF Across Trunks

Nov 7, 2011

I am beginning to implement OSPF into the network I work on. I have a network which consists of multiple 4500, 6500 series routers and 3560s. Each switch has its own set of VLANs. In other words VLAN X on one switch is not the same as VLAN X on another switch. I had envisioned connecting each switch via trunk links and then routing via the loopback addresses on each device. That didn't work. Then I created a VLAN 100 on each switch. Each one was configured with an IP in the same subnet range (10.3.0.1 and 10.3.0.2). I added these addresses to the OSPF process in area 0. It worked. However, this is not desired. I have not seen many examples of 4500 layer 3 switches configured with OSPF. The examples I have seen show the interfaces configured with IPs.

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5596 UP L3 OSPF

Jan 3, 2013

I have 2 Nexus 5596UPs with a layer 3 cards that are exhibiting some very peculiar behavior.  The systems are running 5.1(3)N1(1).I have configured 2 VRF contexts each running their own OSPF process.  There is a static gateway of last resort configured on each VRF, which is to an upstream pair of 5585X's in Active/Active.  Each OSPF process has the "default-information originate always" command configured, however, backbone neighbors are not recieving a gateway of last resort from the 5596UPs.  The applicable configurations are show below.  All other routing information is passing correctly between devices in the network.  This network is not production, it is a proof of concept for a larger implementation.

View 26 Replies View Related

Cisco Switching/Routing :: 867VAE-K9 Is Missing OSPF?

Dec 12, 2012

I have a 867VAE-K9. On feature navigator it is listed as supporting OSPF. However when I go into config mode and type "router ?" BGP is there, but OSPF is not. Also, under my tunnel interfaces there is no support for any OSPF commands such as "ip ospf cost" etc. I'm in the process of raising a TAC. I have tried five or six different versions of IOS code that is available for this device, in each, we never see OSPF listed but sometimes see "router odr" or "router lisp"...

View 5 Replies View Related

Cisco Switching/Routing :: OSPF Not Up Between 4510E And ASA 5540

Sep 28, 2012

between 4510 E(172.29.95.2) and ASA(inside IP 172.29.95.19) ospf not up, but between L3 interface tenGig 6/1 OSPF running with area0 [code]

View 3 Replies View Related

Cisco Switching/Routing :: Two Ospf Processes On ME-3600x

May 30, 2012

I have a problem with ME-3600x running two ospf processes. Proc1 is WAN and PRoc2 is LAN. I am redistributing routes into both directions. After a WAN outage ,  certain wan routes did not get redistributed into the LAN process. I had to do a clear ip route to fix the problem. Has anynoe seen such a scenario with ME-3600x or any other switch/router

View 8 Replies View Related

Cisco Switching/Routing :: 6500 - Campus OSPF Configuration

Aug 26, 2012

I manage a small/medium sized campus network consisting of 4 Cisco 6500 series chassis (each with SUP720's) and a couple hundred Cisco 3550/3560/2960 edge switches. We recently completed a new leg of fiber that will make a completed loop between all of the 6500's .... before I make the pyhsical connection I need to figure out my OSPF entries on each 6500 switch.

View 4 Replies View Related

Cisco Switching/Routing :: 3750v2 Any Limitations To OSPF Process

Jan 2, 2012

I've been reading the documentation for the new 3750v2 switch, and I'm wondering is the IPBase license supports FULL OSPF. The product sheet notes that it supports OSPF in the IPBase license, but then further down the page it notes that for advanced routing functions (EIGRP,OSPF) you need the IPServices license. Are there any limitations to the OSPF process on a 3750v2 with the IPBase license?

View 3 Replies View Related

Cisco Switching/Routing :: 3560X-24P-L Switch OSPF Support?

Mar 21, 2012

I acquired a 3560X-24P-L Switch which I wanted to use at our datacenter.  However, I need a switch that supports OSPF.  It came with a Universal IOS but there was no "Router" command under conf t.  I downloaded and applied the latest "IP Base" IOS, but still no Router OSPF.  Based on the matrix here > [URL] I thought "IP Base" supported OSPF, but what exactly is "OSPF for routed access" ?  Do I actually need an "IP Services" IOS?  From my download options, I do not see an IP Services IOS for the 3560X-24P-L so I'm left to assume that the switch does not support L3 / OSPF.  So my question is this particular switch supports L3 / OSPF and what is Universal IOS?

View 5 Replies View Related

Cisco Switching/Routing :: 3550 OSPF Default Route

Aug 19, 2012

I'm working on a little OSPF setup in my lab and having a problem pinging out to the internet.I have a setup with (3) 3550's running ip routing. I'm configuring OSPF but I can't ping the internet from any L3 switch except the switch with the actual uplink to the internet.[code] From SW2 and SW3, I can ping SW1 on all IPs (192.168.1.90, 10.10.10.1, 10.10.10.5) but I can't ping 192.168.1.1 which is my gateway to the internet.

View 3 Replies View Related

Cisco Switching/Routing :: Configuring OSPF On A Layer 3 Switch 3560G

Apr 12, 2013

Configuring OSPF on a catalyst 3560G Switch to connect to our building next door by way of fiber.  The other two switches in the other building are running OSPF, I am trying to connect to the other building and access a server which is on a switch running OSPF.  I am trying to configure the switch here to run OSPF and be able to see the neighbor, but currently can't although I've identified the networks.  Maybe I'm missing something, I've followed the instructions but  something is not right.

View 15 Replies View Related

Cisco Switching/Routing :: 3750 - How To Distribute Static Route Via OSPF

Mar 26, 2013

We have a 14 offfice MPLS network.  All offices have Cisco 3750s running OSPF which replicate route tables via our providers BGP peers.   I am introducing a new network in our SF office which is not directly connected so in SF we have a static route "ip route 172.16.20.0 255.255.255.0 192.168.100.1. I want our other offices to learn this route route via OSPF so that they know how to get to the new network.  My problem is that of course remote sites do not see our static routes and i  have tried to add this via ospf but the switch will not propagate this route because it is not directly connected to the switch in SF.
 
router ospf 1
log-adjacency-changes
network 10.2.0.0 0.0.0.255 area 2.2.2.2

[Code]......

View 5 Replies View Related

Cisco Switching/Routing :: 3660 - ASA OSPF Filtering Inbound Routes?

Feb 11, 2013

How filter inbound routes in Cisco ASA OSPF? Because Cisco ASA has no "distibute-list" command for OSFP process configuration, I try to use "filter-list" command in area definition. So, I try to use next configuration:
 
R1 (Cisco 3660):
 
skip 
!
router ospf 1

[Code].....

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 6503 OSPF On Vlan Interface?

Oct 24, 2011

i'd like to configure OSPF on a Catalyst 6503 IOS 12.2.17.i habe an Gi1/9 with the ip address 192.168.97.30/24 and a VLAN 19 with the IP Address 192.168.19.0/24.I configured OSPF like this
 
router ospf 1
network 192.168.97.0 0.0.0.255 area 10.5.0.0
network 192.168.19.0 0.0.0.255 area 10.5.0.0
 
on the ospf peer is see that the adjaceny is established but i don't get the routes for the 192.168.19.0 network i checked the ip ospf interface vlan 19; i got ospf is not enabled on the interface then i tried to configure

int vlan 19
ip ospf 1 area 10.5.0.0
 
but it does not access ip ospf 1

View 3 Replies View Related

Cisco Switching/Routing :: 4507 Pb To Propagate Ospf Routes To Another Router On

Nov 15, 2011

On a 4507 v12.2(20)EW, the connected subnets which are declared in the ospf instance are not propagated to the MPLS carrier router.Only the static routes which are redistributed in the ospf instance are propagated to the MPLS carrier router.

View 1 Replies View Related

Cisco Switching/Routing :: 3560 - OSPF Load Sharing Design

Sep 16, 2012

We have our network setup as displayed in the attached. We have 2 HQ offices and 1 branch office. The branch office needs to connect to resources located at both HQs but taking the most effecient path. We have ethernet circuits connecting from each HQ to 2 x Cisco 3560 switches in the branch. HSRP has been configured on the 3560 switches with SW1 as active and SW2 as standby. OSFP has been configured in a single area 0 and the path cost on the link between HQs has been increase to allow 3560 SW1 to route to HQ1 directly and HQ2 via 3560 SW2.The 3560s are connected with a trunk with a L3 SVI for OSPF. This seems to work ok but I have noticed that the branch could become transit if the HQ1 to HQ2 link breaks. How can this be avoided? I realise that if we configure the branch subnets and SW1 to SW2 link in a stub area (area1) then all traffic will route from SW1 to HQ1 and will never share over SW2. I'm assuming that this is because OSPF chooses inter-area routes over intra-area.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved