As long as I have been doing this stuff, I have never had a clear understanding of all of the 6500 boot images and statements. The more I read online, the more I get confused.
1. What is the boot image "boot-mz" for? Where should it be placed (i.e. bootflash)? what command do I need to issue in order to use the boot image I want?
2. What is the IOS rommon image for? I thought the rommon image was the boot image but apparently these are two different images. Where should it be placed (i.e. bootflash, sup-bootflash, etc). What command do I use to ensure that I am using this IOS rommon image?
We have got a big problem with our NAM (WS-SVC-NAM-1) - it does not boot. We have got a second one and in an other chassis. I changed the chassis, and RAM and Flash from the other one. RAM and Flash are ok.
We checked the disc (hardware) with an Ontrack-tool -it is OK.
environment: 6500 VSS
sh logging: Jun 17 13:18:24: SW1_SP: Switch 1 Physical Slot 7 - Module Type LINE_CARD inserted sm(cygnus_oir_bay slot7), running yes, state wait_til_online Last transition recorded: (offline)-> empty (remove)-> empty_clr_persist (remove)-> empty (insert)-> may_be_occupied (timer)-> occupied (known)-> can_power_on (yes_power)-> powered_on (real_power_on)-> check_power_on (timer)-> check_power_on (power_on_ok)-> wait_til_online
document which explians normal booting sequence in a 6500 Switch running IOS. What I am looking for is in which order the image is loaded in SUP, RP, SP etc
One of the 6500 was going in bootrom mode, so I have formated the flash disk using the other Cisco 6500 switch and copied IOS file to the boot disk. But the 6500 booting failed.
The network gods recently updated our 6500 and upon reboot, the FWSM booted to CF:1 maintence partition,which caused an immediate outage. On the router, I ran the following command to set the default FWSM boot partition to the configuration with:Router#boot device module 4 cf:5 However, it appears the "show boot device" command has been replaced with "show bootvar" which doesn't show me which partition the router will boot the FWSM to. Is there a command I can run from the Router that will actually confirm the boot partition for the FWSM if the router reloads.
direct me to a document detailing the order that line cards are supposed to boot in a 6500? I'm noticing random boot sequences in some of my chassis,?Note: We currently run Sup720 3CXL for the most part.
The config is from our MPLS router located in HeadOffice, ^controlled-ospf ^ whats its function^ routes_in ^ whats its functionhow to change standard acl to extended acl.
The configuration for the natting is something like this [code] If I understand the config statements 10.232.50.98 is natted to 32.x.x.66 and 10.232.50.99 is natted to 32.x.x.69 , but do we need reverse natting stements as well to work this ?
I would like to config "when host X on v lan X goes to a network that is across an ip sec tunnel, for which v lan X network is not in the encryption domains, translate host X address to that of the asa in a network that is part of the crypto domain".
Interface vlan544 (172.16.80.0/24) is the local encryption domain, and 10.1.0.0/29 holds some monitoring servers that should not be part of the encryption domain, but rather get it's source address translated to that of the firewall in 172.16.80.0/24. Here's how I did:
# Vlan522 for 10.1.0.0/29, need to somehow have a specific nat here I guess that falls between the no nat and the generic "nat the rest to the global) [code]...
This obviously didn't work, the second (number 2) rule is never hit. What am I doing wrong?
I used the following statement to create Dynamic PAT to public IP address:
object network INSIDE_10.6 nat (any,any) dynamic PAT object network INSIDE_192.168 nat (any,any) dynamic PAT
Is that correct? Also I'm using one public address to PAT both inside networks. Is there any dvantage of using 2 different ones, so each inside network would be PAT to its own address?
nat (inside) 1 10.1.1.0 255.255.255.0 global (outside) 100.1.1.1 nat control is turned off.
By my understanding any traffic from the inside to outside interface will be PATted to 100.1.1.1. However, communications between inside and the DMZ will not be PATted, and should work with no problems.This seems to be corroborated by this document: [URL]Which states:"The adaptive security appliance translates an address when a NAT rule matches the traffic. If no NAT rule matches, processing for the packet continues."EDIT: I may have misunderstood the above statement.I found this guide to configuring NAT/PAT: [URL]It states:"When you specify a group of IP address(es) in a nat command, then you must perform NAT on that group of addresses when they access any lower or same security level interface; you must apply a global command with the same NAT ID on each interface, or use a static command. NAT is not required for that group when it accesses a higher security interface because to perform NAT from outside to inside you must create a separate nat command using the outside keyword. If you do apply outside NAT, then the NAT requirements preceding come into effect for that group of addresses when they access all higher security interfaces. Traffic identified by a static command is not affected."My problem is that packet tracer does not seem to bear me out. It tells me the packet is dropped due to "no matching global" when I source traffic from the inside interface and send it to the DMZ.
Is there a cisco best practice on the maximum number of NAT statements on a Cisco ASA? We have a 5520 and a coworker is adding static NAT policies so a vendor can monitor around 1,029 nodes. The problem is each node inside is a 10.X.X.X and to keep the IPs from overlapping with other customers the vendor monitors they would like us to NAT to a 172.16.X.X scheme.
I am trying to set a logging discriminator that will drom any message contans the mnemonics etc. "ABC" and "XYZ". As fists step I configure this:logging discriminator nolog mnemonics drops ABC
but when I am trying to add a second statement.logging discriminator nolog mnemonics drops XYZ
in the same discriminator (nolog) it replaces the first statement with the last. So in the show run I have always one statement for discriminator "nolog". Finally, how can I configure a logging discriminator with more than one statement? I am using IOS Version 12.2(33)SRD4 on a Cisco 7609.
I have a 6509 running s72033_rp-ADVIPSERVICESK9_WAN-M version 12.2(33)SXH5. Four incorrect bgp aggregate-address statements were entered in which overlap. Attempted to remove the statements but they won't come out.
I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
I have a new asr9010 that I want to upgrade from 4.2.0 to 4.2.1 sofware. When i try to run the "install activate isk0:asr9k-mini-p-4.2.1 sync" it fails and complains that the 2 files below or equivalent must be active.
iosxr-infra V4.2.0 iosxr-fwding-4.2.0
When do a show version i can see files are loaded and on the asr9010. Attached is a show tech
I own 2 different Panasonic IP cameras (BL-C30 and BL-C210A), which in the past have been able to FTP captured images to a host (in this case, the UGOLOG service). Upon upgrading my router to the D-Link DIR-655, this ability stopped. I also tried HTTP transfer, and this too is now unsuccessful.I can access these cameras from the internet, so the router is properly opening the ports. In my testing, I was able to FTP directly to the site via browse (ftp://) with no issues at all. The port/userid/password was accepted. On the cameras, I've played with login timing and data transfer method (active/passive), to no avail. The cameras report: Could not connect to FTP server. (panasonic error code: 133 80005008H) and FTP error 426: Connection closed, transfer aborted.On the DIR-655, firmware Version :1.35NA.
I search for the both files, because I want to configure one ASA with 8.2.1 and the other ASA with a 8.4.x image to see the differences between both versions. But I don`t have a account to download the ASA Image 8.4.x an the ASDM 6.4x to test it.Is there a chance to get those Images without a Account.
About two days ago my laptop started having problems with video playback on flash websites and pixelation/off-color images on every site I go to. The videos will be playing and then suddenly will start "tiling" and glitching around wile images will either not show up, show only half of the image, show up half "normal" and half pixelated, or be completely pixelated and blocky. This only started happening just recently and has never happened before.
I have several network cameras within my home. Some are Panasonic. How can I view the image without using their cgi. I just want to view the camera image within my security program. How can I do this?
Whenever I load a gallery of images or even when I open up a couple of websites, sometimes the image/website won't load and is perpetually loading, only to time out minutes later.I've tried out different browsers (Chrome, Firefox) on my wired desktop and tried this on my Laptop through WiFi with the same two browsers. The result was the same each time. So it's not about faulty computer hardware, software or malware on the machines. [code] When I ran a Speedtest.net test, this weird issue happened on the end-result screen. Normally when you do a test there, you can share/compare etc. But for me, that content did not appear.On Reddit I browsed a couple of ragecomics for my leisure and then some of the img.ur hosted images won't load. I know this issue still exists, because I use Randomly ordered wallpapers / Wallbase.cc to test out the case. By using this link, you're presented with a bunch of random thumbnails. So I scroll down and keep loading thumbnails as fast the website and I can endure. But at one point, it will stop at a random thumbnail, load the first 20% of the image and freeze. Or it will load 20%, freeze, and continue loading the rest. I also tried this out by opening wallpapers, closing them with CTRL+W, repeating this process until one of them refused to load, but when I refreshed the browser it would magically load the image.
I have reset my modem and my router, the router has been restored to factory defaults. So I'm clueless on what could be the cause of this weird issue. Nothing in the LAN has changed, this started about a week ago. I've narrowed it down to the router, but there's nothing in the settings that would cause this behaviour.
I noticed my tumblr dashboard was loading corrupted thumbnails. I first thought that tumblr was having problems, until it started happening on my deviantArt, and YouTube. I was worried that it was my computer, but then the same thing started happening on my moms' Macbook, and then her Wi-Fi streaming television started corrupting the video. And then, sometimes a website won't load fully, but will instead load part of it's code, or instead my browser (I've tried on Google Chrome, Firefox and IE) tells me the webpage is unavailable, or doesn't exist. It'll load up semi-properly (with the corrupted images still) after a refresh or two, but it's tiring and worrisome.
WDS allows you to capture and deploy images on a network to client pcs. I Was wondering how many images wds allows you to capture and deploy and if there were any work a-rounds that would allow you to deploy more.
Whenever I access a file through HTTP, it seems to require that I completely load the file before it will display.
1) For large images, this will result in the whole thing taking some time to load before displaying in its entirety, unlike the usual progressive rendering.
2) For file downloads, this will result in the file being downloaded only after being cached, appearing only when the whole file has finished downloading, unlike the usual process where it can be seen as a progress bar in the browser's download window (for some reason, FTP downloading seems to work normally)
3) For internet streaming video, this means the video will not display until the whole video has been buffered (i.e. will not play until fully loaded)
1) I am on a home network. Other computers (including my old one) do not exhibit similar problems 2) Using Firefox 9.01 3) Win 7 SP1 4) Realtek PCIe GBE controller
