Linksys Wireless Router :: E4200 - Can't Upload At Normal File Size
Jul 8, 2011
I have an odd problem with the FTP server. I currently hooked up a 250GB portable HDD which is formatted in NTFS. A single folder in the root of the drive is mounted as the FTP server. Every time I upload a zip or far, the file comes out ends up being uploaded corrupt and double the original file size. I have used 2 FTP clients, using either ASCII or binary. No matter how I go about it, I can't make the files upload at the normal file size. Its not just archives, however, I tried an mp3 and it too got uploaded corrupt and double the size. I then downloaded the mp3 to try and play it but it didn't play in windows media player. However I loaded the 'corrupt mp3 into audacity and the file played like normal.
View 5 Replies
ADVERTISEMENT
Oct 18, 2011
if Linksys will be increasing the size limitation of the E4200 USB storage devices? Will the next firmware allow larger drive sizes? I only bought the thing to share via the router my digital content that is stored on an 8TB external device. What is the perpose to the limit in the first place? Is this a hardware or software limitation of the device?
View 2 Replies
View Related
May 31, 2011
Enabling auto detection of the upstream bandwidth in the qos tab results in a significantly lower than normal maximum upload speed? I have the Blast plan from comcast (20/2 sustained; 30/4 with powerboost). Here are the results.
With the Qos OFF:
View 9 Replies
View Related
May 4, 2012
I have an e4200 and every once in a while a few files on my USB Hard Drive will change to an empty folder. What do I do to change the file back to its original format and what do I do to keep this from happening again later? I have photos that are not replaceable and do not want to lose them?
View 5 Replies
View Related
Apr 26, 2011
I've verified that the router and the pc have the same time zone, daylight savings update specification and that they both showed the same time (00:56AM). But a file created on the attached USB device was timestamped 01:56AM (the date was correct).
View 9 Replies
View Related
Mar 24, 2013
I just upgrade my service with Comcast so I can now get up to 50Mbps, however the modem when directly connected to the PC can obtain these speeds, it does not when the PC is connected to the E4200 router. In fact the Cisco Connect speed test shows the upload speeds (10+ Mbps) to be faster than the download speed(4.82 Mbps). I upgraded the firmware to the latest level but it did not make a difference.
View 4 Replies
View Related
Aug 29, 2011
I'm using .01 firware and I notice that after I reboot the router I get duplicate filenames on the HD attached to it with the video files. What folder or config file can I delete so it will do a clean rescan? please fix the E4200 media server in .02 firmware
View 9 Replies
View Related
Mar 24, 2012
I have recently purchased a Cisco E4200 to replace my D-LINK DIR-655, which I thought was defective because I was getting slow wirless file transfer speed, regardless of setting, location and client.Using the E4200, when I transfer a file from a PC to another, both connected at 300mb on the 2.4ghz band, the file transfer rate reported by windows 7 and networx is from 2MB/s to 3.5MB/s. I think those transfer rates are not acceptable. Is that a good assumption ? I would expect something in the range of 10MB/s (which is what I get with a cheap dlink router, wired)
I also had great difficulty finding a channel. I had to try them all one-by-one as the auto channel selection made my PCs connect at 130mb.The E4200 is setup as follows:
-WPA-Personal
-Channel 5
-802.11n only
I have tried 3 different computers with different network adapters and they all underperform (IMO..).There are no other wireless networks in my area.I also took the E4200 to my office which is very crowed. Every single channel is occupied by several wireless networks. I get a file transfer speed PC to PC of about 2MB.I basically could have kept my DIR-655 as the speeds are identical.
View 4 Replies
View Related
Feb 9, 2011
is it possible to upload a htm file to the router using a command prompt? the page is located at [URL] I want to change the option of Allow All to Restrict Access at 8pm every night?
View 3 Replies
View Related
Jan 2, 2011
What is the ratio supposed to be between the download speed and the upload speed in a normal working configuation? My webpages are taking forever to load. I used this speedtest... url...
-download speed: 7.427 Mbps
-upload speed: 0.006 Mbps
My provider is cable, Brighthouse, hooked up to their Scientific Atlanta modem and from there it is hooked up to a Belkin Connect N150 wireless router. I am not using the wireless on my laptop but am wired directly to the router. [code]
View 3 Replies
View Related
Nov 1, 2011
I want to download the iOS update to my Cisco 2800 Series Routers and Cisco Catalyst 2960 Series Switches and leave them there till im ready to install them. Is this possible?
View 1 Replies
View Related
Sep 13, 2012
how do i set limit on the log file size in ACS 5.3. I had the same issue with Nexus 1000v but there is a command that enables you to set log file nane and size. it is getting bulky.
View 7 Replies
View Related
Nov 22, 2012
We have lms 3.2 that we are facing a problem with it. When we start the server the EDS-GCF log file size start to increasing rapidly until it consumes up all free space and it only stops when we stop the Daemon Manager service. I tried to do the pds how command but I get no output from it. I included the portion of the EDS and EDS-GCF log files. i searched and didn't find the cause of this error.
View 3 Replies
View Related
Jun 8, 2013
i have LMS 4.2 in Network with 100 devices, all of my devices have ACL so, there are too many logs in syslog
after a while the size of the log files in /var/log files (boot.log, messages.log) going to have huge size, something about 20G for each one
I'm looking for a way to reduce the size, is it possible to use Log Rotation or not?
View 1 Replies
View Related
Mar 24, 2011
I am currently trying to upgrade a 2800 series router to the latest IOS. I have loads of space on the router but the issue seems to be that Pumkin can't handle the size of the file. Keeps failing and saying that I might want to increase my block size. I increased it to the maximum size but still didn't work.
View 5 Replies
View Related
Jul 12, 2012
I am having difficulty uploading files on the internet because the speeds are so slow. My download speed is 23.88 MBPS, bu upload is .3 mbps. This seems to be a recent problem. The other computers on the network get upload speeds of 5mbps and do not have any problem, so I think there is some problem unique to this computer, and not a network problem. I can't back up my files because the speed is too slow.
View 8 Replies
View Related
Aug 9, 2012
First is it possible to change the length that new files will be created? Right now it creates 1 minute chunks which becomes a pain in the butt to manage. I would really like to set the length to 10min or even 60min chunks as one minute is just to short. I use the camera for constant recording and do not plan on puttin in a computer to record to due to logistics.
Secondly, is there software that will manage these files? That is pull down from the cameras SD and archive then allow you to simply play from any location via mouse or time picker?
I have used professional security systems in the past and know that this is just an entry home consumer camera but was hoping it had a little more functionality, as it stands the built in SD recording is almost useless without some sort of management software.
View 2 Replies
View Related
Jul 12, 2012
Is it normal for an E1000's LEDs to get dim after a few years??Because my LAN port #1 and #2 are dim, as well as the power LED.I'm guessing it's just because they are always on?
View 5 Replies
View Related
Jun 4, 2011
I was uploading a big 2gb file to my FTP server, it was all going good and I managed to upload the whole thing hassle free. After I finish I log out, and return about 3 hours later and try to log back in, to no avail.WinSCP gives me the following error:
[code]....
View 1 Replies
View Related
Nov 18, 2012
I accidently went into bridge mode on my linksys E2500 router. I want to reset it back to normal but i'm not sure how to do it. i tried the little reset button on the router but that didn't change it.
View 4 Replies
View Related
Jun 24, 2011
I can't upload on file-sharing sites , I have tried to upload on wupload.com , fileserve.com , ****file.com and other sites and I click to upload but the progress don't start only stay in 0% I have waited 3 hours to upload a music with 150 MB and still in 0% progress .
View 5 Replies
View Related
Nov 9, 2011
I am using WiSM in 6509, this WiSM has two controller with the same management IP subnet, I tired to upload the configuration to the TFTP server, but tried many times, one of the controller working well, but the other one always cannot reach the TFTP server, here is the debugger log for both controller
Failed one:
(KGV-WiSM-1) >debug transfer all a enable
(KGV-WiSM-1) >*TransferTask: Nov 10 16:26:08.735: RESULT_STRING: TFTP Config transfer starting.
*TransferTask: Nov 10 16:26:08.735: RESULT_CODE:1
*TransferTask: Nov 10 16:26:32.018: Locking tftp semaphore, pHost=172.16.102.107 pFilename=/KGV.aes
*TransferTask: Nov 10 16:26:32.018: Semaphore locked, now unlocking, pHost=172.16.102.107 pFilename=/KGV.aes
[code].....
why the controller can't upload the file, I can ping both controller and both controllers can ping to the TFTP server.
View 8 Replies
View Related
Jun 6, 2012
Is it normal for the "CISCO" icon/light to "fast flashing" periodically - not to be confused with the "slow flashing" that the E4200V2 displays when being "power cycled"?
View 1 Replies
View Related
Jan 11, 2012
are there any free services where you can remote upload a file (zip file 25MB) and have it sent to me via email as an attachment. not a link where i have to download the file.
View 1 Replies
View Related
Jun 27, 2012
I want upgrade my switches 2960-24PC-L RAM: 128MB and Flash: 28MB, but in the web page of cisco I see that the requirement of hardware is RAM: 128MB and Flash: 32MB.
I download the IOS file and this file is only 11.2MB so my question is if I can upgrade the IOS because my flash is enough for upload the IOS file.
View 12 Replies
View Related
Sep 27, 2011
I am using filezilla (ftp client) to upload to file server as well as other sites including free host and 000webhost, on large files my upload fail near the end,This does not happen if I bypass my e200 router, so it must be something about the the e2000 that is causing the failures.
View 2 Replies
View Related
Nov 22, 2012
I've hooked up an external usb drive to my EA4500 and i have enabled the FTP server so a friend of mine can download from the drive. Thing is though, that i want to limit the the upload of the ftp server so it wont be using the 100% of my ISP's upload bandwidth. How can i do that? I have the latest cisco connect cloud firmware and i go to Media Prioritization>Settings and set the upload to what i want, but he still downloads with the max speed of my upload..
View 6 Replies
View Related
Jan 21, 2011
I cannot upload files through http (e-mail attachments, send images to Facebook, send file to virustotal.com) with Linksys WRT600N router. When I remove connection cable from router and place directly in a computer, everything works just fine. I am using last firmware upgrade.
View 2 Replies
View Related
Nov 13, 2012
I upgraded my old router to a Linksys E1200 about 2 months ago. Like others with Comcast, I now have a lot slower internet speeds. I've updated everything, disabled WMM. I'm still getting slow speeds. My download speed is 3.12, which is not that bad for me. However, my upload is just below 1.
View 7 Replies
View Related
Jul 11, 2012
I bought an E2000 router as a replacement for my WRT54G router, since my internet speeds had been upgraded. But this E2000 router has been giving me nothing but trouble.
Wired through both the router or modem, I get my topspeed of 110mbps. However, as soon as I switch over to the wireless N function, my speed drops to only 25mbps. As far as I know, wireless N should have a much faster speed than that. Even my old WRT54G had faster speeds than this new router has. Mind you, that the distance between my laptop and router is about 3 inches away. The further I go away from my router, the speed exponentialy drops (20 feet, and the speed even drops to below 10mbps). Even with different laptops that have completely different wireless cards. Now honestly, I have tried EVERYTHING to get the speed up. Both 2.4 and 5ghz, 20mhz only, 40 mhz only, different channels (currently the router is in channel 11, being the only router in that channel), setting the network to G-only. I tried changing the Beacon interval thing in numerous settings, I even tried changing the MUT. Firmware is completely up to date. I have also tried placing the router on a completely different place, to make sure there was absolutely no interference (tough that shouldn't be an issue if my laptop is only 3 inches away) I tried changing the security mode to something different than WPA2/AES.
Nothing worked, if anything, it made it worse in some cases. I have litteraly tried every option I could find online, except for trying a third party firmware like DDWRT, which worked excellently for my old WRT54G, though I read that speeds can't be improved on this E2000 with a third party firmware.
Is there anything else I can do, or should I assume that my router is defective?
When I'm in my bedroom, I get a very poor connection and my speed drops to about 0.25mbps. Abysmal, so I bought a WiFi range extender to get me a better signal. It works, and it allows me to get a speed of about 5-6 mbps, without dropped connections. Still slow, but at least it works. The weird thing is, wired through my router or modem, I get about 9mbps upload speed. With this extender, I get the same 9mbps upload speed in my bedroom, though only 5-6 mbps download speed. You'd think that the upload speed would drop simultaneously with the download speed. How can my upload speed be higher (maxing out) than my download speed? I wonder if my transmitting antenna of my router isn't defective.
View 9 Replies
View Related
Sep 12, 2012
WRT160NL exchange download and upload speeds.Before the router everything is fine, then it wireless or Ethernet port occurs above situation.No difference what firmware it is (1.0.02, 1.0.03, DD-WRT...)
View 7 Replies
View Related
Feb 28, 2013
i recently switched from a wrt54g to a Cisco e1200 and my average torrent download and upload speeds went to 1200/kbps 100/kbps to around 200/kbs 0-1/kbps i got the latest firmware tried different channels disabled the wmm I've also tried wireless n only and wireless g only. I have no way to test the wired speed. I have a n adapter.what do i do.
View 9 Replies
View Related
May 13, 2013
Since we purchased our router in February, we've had intermittent problems with speed, and now it seems to be permanent. If we connect directly to the Comcast modem, everything is fine. If we connect to the router, directly or wirelessly, speeds drop to <3.
View 9 Replies
View Related
