WRT160NL exchange download and upload speeds.Before the router everything is fine, then it wireless or Ethernet port occurs above situation.No difference what firmware it is (1.0.02, 1.0.03, DD-WRT...)
View 7 Repliesi recently switched from a wrt54g to a Cisco e1200 and my average torrent download and upload speeds went to 1200/kbps 100/kbps to around 200/kbs 0-1/kbps i got the latest firmware tried different channels disabled the wmm I've also tried wireless n only and wireless g only. I have no way to test the wired speed. I have a n adapter.what do i do.
View 9 Replies View RelatedSince we purchased our router in February, we've had intermittent problems with speed, and now it seems to be permanent. If we connect directly to the Comcast modem, everything is fine. If we connect to the router, directly or wirelessly, speeds drop to <3.
View 9 Replies View RelatedI just upgrade my service with Comcast so I can now get up to 50Mbps, however the modem when directly connected to the PC can obtain these speeds, it does not when the PC is connected to the E4200 router. In fact the Cisco Connect speed test shows the upload speeds (10+ Mbps) to be faster than the download speed(4.82 Mbps). I upgraded the firmware to the latest level but it did not make a difference.
View 4 Replies View RelatedAfter recently intalling the WMP600N wireless adapter I have had great trouble getting it working properly.
Current performance
- signal: verygood/ excellent
- download speed: ~1mb
- upload speed: ~2mb
- signal speed: 18-54mbps (lots of variance but never above 54)
Comparison to my laptop
Laptop in same location with wireless G capability
- signal: verygood/ excellent
- download speed: ~20mb
- upload speed: ~2mb
- signal speed: 54mbps
my router is a D-Link wireless N router I recieved from my ISP. I do not believe my router is to blame for this problem since I have a laptop with an inferior wireless adapter recieving 20X the download speed.Drivers I have installed the latest drivers for windows 7 and I am running windows 7 Ultimate 64bit.
I have a RCA modem from comcast high speed internet.Also have a Linksys Cisco Wireless-N Gigabit Router model # WRT310N V2. When I connect the internet directly into the computer, I get download speed up to 21.07 mbps and upload speed of 3.07. When I connect through the router download speed 1.31mbps and upload speed of 1.01.I have no clue how to make changes to the router.
View 19 Replies View RelatedMy router is dropping the downloadspeed from 20mb to 1. After turning off and on, the router restores for a few days.
View 3 Replies View RelatedI did a search and came across this board because I too am having the same issues with wireless connection. I went as far as buying a new router, which like the original post stated, worked well for a few and then stopped. It's frustrating because I need the wireless connection for many items I use at home.
View 2 Replies View RelatedI'm having really slow speeds surfing the internet, watching videos on sites like youtube, and downloading files. So i went to [URL] and found that my download speeds are only 1.3 mbps!! my upload is fine, around 5 mbps.I am wirelessly connected to the router, but the signal strength is fine.
View 2 Replies View RelatedWe recently bought a home and just moved in. That being the case, we got a new ISP (Cincinnati Bell DSL). The service is advertised as "Up to 5Mbps."
My current equipment:
PC:
OS Name Microsoft Windows 7 Home Premium
Version 6.1.7600 Build 7600
Other OS Description Not Available
[Code].....
So what can I do to achieve faster speeds? Am I limited by the hardware I have? My Dell is roughly 6 years old. Am I limited by Cincinnati Bell? Is it the location of the wireless router? Are there settings I can adjust to create a faster connection?
I have a synchronous 10 Mb connection to my isp which I have conneted to a CISCO asa 5510. I have done a lot of testing and there is a very noticable difference in my upload/dowload speeds.When I connect a laptop directly to the Cable from my ISP's equipment and have the NIC set to autosense, I get similair results for Download/Upload Speeds I have tested and get 9 plus down and 8 plus up.When I either connect the asa directly to this cable and set to either 100/Full or autosense OR I place a non-managed switch in between the asa and the ISP's equipment My upload speed drops dramataically. The Download speed stays about the same 8 Mb Plus but my upload falls off the face of the earth drops to about a 1Mb. I have noticed this many times when I am going from a cisco 800 series router to a Cisco ASA.This is severely limiting my ability to perform replication out from my locale.
View 7 Replies View RelatedI upgraded my old router to a Linksys E1200 about 2 months ago. Like others with Comcast, I now have a lot slower internet speeds. I've updated everything, disabled WMM. I'm still getting slow speeds. My download speed is 3.12, which is not that bad for me. However, my upload is just below 1.
View 7 Replies View RelatedI have an E1200 that will work fine for a while, then suddenly the download speed for all wireless devices will drop to between 20-30 KB/sec. It happened last night when we were watching videos on Hulu. We were blazing along fine, when all of a sudden the connection was horrible enough that we had to stop watching. We have no idea what changed - there are only two of us in the house and we were both passively watching Hulu.
This has happened before, and usually changing something like the wireless channel has fixed it, but not this time. The PCs we have that are connected to the router via Ethernet get between 1-3 MB/sec, so I know it's not the modem or the ISP.The signal strength is good (4-5 bars). I have tried repositioning the router and the wireless reciever but that hasn't worked.I have the latest firmware for the router as far as I know (v2.0.02).
I have tried every channel available (including "Auto"). I have tried switching the Channel Width between Auto and 40 MHz. I have tried resetting the router to factory settings and re-uploading my configuraiton. I have tried setting QoS.
I have been experiencing intermittent issues with download speeds of 1-3 MB and ironically upload speeds of almost 10MB. When everything is working fine I get download speeds of about 35MB and upload speeds of 5MB which is normal. This issue comes and goes. I had Comcast come out several times and we finally pinpointed it back to the WRT400N router. The Comcast modem is a Cisco DPC3008 model. I know there are known issues with the Cisco WRT400N but have had a hard time finding the information. Any known issues for this model and if so what are the fixes. BTW, the firmware is up to date.
View 2 Replies View RelatedI Have BT Infinity and they are pushing 70mbps to my house ....i bought an EA6500 and i had real bad internet speed but amazing conection speed with my BT Home HUB3 ... 23Mbps with Cisco EA6500 and 68Mbps with my BT Home Hub3. I found out it was the Media Prioritization so just to be safe i reset my factory settings and made sure it was turned off. Just like magic i get the same now as the BT Home HUB3 .
View 1 Replies View Relatedi have WRT610N v1.0 with latest original firmware but ftp upload speed and torrent download speed is terribly slow.
View 3 Replies View RelatedI have been having a problem with my router for the past two weeks and my ISP (RCN) has done nothing to fix it so maybe with our nerd power combined we can find a solution!My router runs fine about 60% of the time, I get 20-24Mbps down and 2Mbps up connect wirelessly. the other 40% of the time the download speed suddenly drops to 1.5-2Mbps down and 1Mbps up. There is nothing in particular that I will be doing at the moment it just suddenly dies.Things I have done that have not worked.I have changed my channel to 1,6,and 11.Updated firmware.Factory Reset (New broadcast name/password).Set up static IPs.I have tried disabling WMM Support and this just kills any connection wirelessly to the router.Is there anything else you can think of to fix the issue, or should I just be demanding a new router the next time they come
View 1 Replies View RelatedAll I want is functional Wi-Fi in my house like the rest of the world. Unfortunately, I cannot have that for whatever reason.
Now that I said that, Let's me get down to explaining my issue. I orginally owned a Linksys WRT350n. This router worked fine for years, untill one day I decided to do a speed test on my new Motrola Atrix. My Wired computer gets ~22000kbps down and 4000kbps up... My wireless speedtest on my Atrix yielded 2000kbps down and 4000kbps up. I assumed it was the phone, so i went and tried every other wireless device in my house. Everyone of them got the same result.. 2000kbps down.. 4000kbps up.
At this point I went into my router settings and tried every available channel, all of them yielded the same result of 2000kbps down and 4000kbps up.. At this point, I assumed it was the router. Ive had it for a few years and figured it was just reaching EOL. I rushed to my nearest bestbuy to pick up a brand new Linksys E4200. I brought it home, hooked it up and was eager to test my new wireless speeds. Unfortunately the same results of 2000kbps down and 4000kbps up was the yield. Once again, I've tried every possible channel with no change to my speeds. At this point I called up Linksys/Cisco support.. They were POSITIVE it was a hardware issue and had me exchange the router, even though I informed them i had the same issue with my older router of a different model. I went along with it anyway, and exchanged my router. Same issue. I called Cisco/Linksys back up and informed them, and basically they told me "they'd make a note of the issue and call me back at a later date."
I downloaded a WiFi Analyzer on my cell phone. Theres only two other dectable networks in my area, and they are low low low signal. So, I don't believe it's heavy saturation. The router is in the same room as 3 of the wireless devices that get 2000kbps down/4000kbps up. So it's not range either.
I just replaced my BEFSR41 with a new WRT54GL (to get WiFi support in addition to Wired Support). With the BEFSR41 I was getting 50/8 speeds. As soon as I swaped with the WRT54GL my download speed dropped to 30Mbs. Is the WRT54GL unable to get 50Mbs unlike the BEFSR41 or is there something I have miss configured? I am using the same computer settings as I used to and reconecting the BEFSR41 restored my 50Mbs Download Speed. This is with wired connections with the WiFi turned off (to eliminate any question of the WiFi stealing any of the processing power).
View 9 Replies View RelatedI recently set up a new E1200 router to replace my old one. We are having problems with very slow download speeds (often <0.10 Mbps) even while the upload speeds are OK (8-10 Mbps). Our previous download speed over wifi was 10-15 Mbps.When I first set it up, the download speed was very poor on the initial computer. After fooling around, it was fine. I don't know what I did that made it speed up. However, my wife's computer has had very poor download speeds. After rebooting my computer, the download speed has also dropped bak to <0.10. I was able to stream Hulu on my Wii just fine an hour ago.
View 1 Replies View RelatedI have a Linksys WRT160N V2 wireless router that I am using with my Comcast Internet service. When I connect to the router via cable, I get download speeds up to 52Mbs (per www.speedtest.net). When I test my wireless connection, I can only get download speeds up to 14.5 Mbs, even though the Windows “Wireless Network Connection” speed shows 54.0 Mbs. I also verified this with another laptop, and got the same results. I also checked upload speeds, both wired and wireless I get the same speed of 11 Mbs.
Is there some reason I can’t get faster download speeds with a wireless connection?
Recently bought a new Dell XPS8500; it's connected to my Linksys WRT160N router. After running some speed tests in the evenings I noticed I'm only getting around 2Mbps download speeds. In the mornings I'm getting around 20Mbps download speeds (using the same tests). Could this huge difference be caused by my service provider and/or amount of people online in the evenings? Is there anything in the router settings that could/should be adjusted? Below are the release notes for the new firmware version:
1. Fixed issue with NMH series. `
2. Fixed PPTP client cannot get ICMP response from Internet.
3. Fixed issue with NTP
4. Fixed issue with L2TP UDP packets can be received in Internet side.
5. Fixed TZO and DyneDNS not automatically updating.
6. Fixed some Wireless protected setup issue.
[code]....
I am getting very slow download speeds on my wireless router (Linksys model#WRT160N). I measured it on speedtest.net. with my ASUS laptop, ASUS Transformer Prime tablet, and 2 Ipod touches. All similar speeds.
Download avg: 1.30 Mbps
upload avg: 6.20 Mbps
I measured my desktop speed that is hardwired through the router to the modem.
Download avg: 30.00 Mbps
upload ave: 6.20 Mbps
I have scanned all the wireless connection in my area and found them to occupy channels 1, 6, 11. I tried changing my channels one at a time for all 11 channels. Some did a little better than others but not a lot.Also, if I by a dual channel router, can all wireless devices pick up on the 5GHz spectrim and if some, could this alleviate some interference?Is it possible that my router is going bad and a new single channel 2.4 GHz router will be fine?
I just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
I have a Linksys E1200 router, which replaced a Linksys WRT54G wireless router. The WRT54G ran perfectly, but did not support wireless N, so I replaced it with the Linksys E1200. The router is physically located in a good spot, up high and centrally located in my house.Problem is, my download speed on my android tablet, xBox, iPhone is very slow, yet my upload speed is screaming fast.
Wireless: Ping: 30ms, Download 1.93Mbps, Upload 6.27Mbps.
Wired: Ping: 14, Download 17.88 Mbps, Upload 6.7Mbps.
I've changed channels on my router, changed channel width. Connection type is DHCP. My security is WPA2. I use the wireless MAC filter (allow only these MAC addresses access). No parental controls, I don't use port forwarding or triggering, and my firmware is up-to-date. why my speed changed from the older router to the newer router?
is there a way to restrict the upload and download of computers on a wireless network (or at least get the router to favor one computer over the others?)i have a tp-link TD-W8960N router and the computer i need the extra bandwidth on is connected to the router via cable
View 3 Replies View RelatedDownload speeds, per speedtest.net and speakeasy, are about 20mbps.When the speed test gets to the upload part, it usually hangs or takes a long time before giving me a result of about 0.04mbps. Basically, it's so slow, it sometimes just gives up and times out.This translates into a real shoddy internet experience because something as simple as choosing airline tickets requires your computer to "upload" your choices. And of course, if that doesn't happen within a certain amount of time... Timeout! I have tested the connection without my Netgear FVS336G Dual WAN router in the way and it is much better so I'm certain it's the router.When I tell the router to use WAN 2, which is where my AT&T DSL connection is on, the upload works just fine (about .4 mbps - I'm provisioned at 512kbps so it's fine).Also, this is the case on ALL computers on the network - wired, wireless, PC, Mac, iPhone, iPad, you name it. So, it's definitely not device specific.
View 1 Replies View RelatedI have a Linksys E1200 modem and I am only getting less than 1.0 mbps download speeds. When connected via ethernet cable to the router, my download speed is > 50 mbps.
View 2 Replies View RelatedI was using Billion ADSL 2+ modem since last 6 years. It was working well but I need Wireless LAN N speed connection and I bought Linksys WAG320N.After configuring the modem my download speed has come doen't to less than 1Mb/s. When I connect to my old Billion I am getting 16Mb/s. [code]
View 2 Replies View RelatedI recently bought a WRT160NL router. I have a 10/10 Mbps internet connection, but when I am connected via the router it only gives me ~2.5/1 Mbps speeds. Connecting my computer directly to the "wall" results in 10/10 Mbps speeds. I have tried connecting to the router both wireless and by wire, it makes no difference. The internal wired and wireless speeds are fine, as I have copied files over the internal switch and via the wireless network at relatively high speeds. I have not fiddled with any connection settings except creating a few permanent DHCP leases.
View 6 Replies View RelatedFirmware is not available for WRT160NL in this site. Only Setup Wizard and Firmware Upgrade Instructions are available.
View 1 Replies View RelatedI usually get a solid speed of 2.3MBss yet today I am getting only 500kb/s I have reset my router 3 times, and my computer twice. Why is it happening?
View 1 Replies View RelatedI have been searching for about 2 days now about this problem and have tried almost everything I can think of to fix it but none seems to work Okay so I have a ISP package for 55 Mbp/s Down and 3 Mbp/s Up but when connected to the router either lan or wireless I am speedtesting at about 15 Mbp/s. I have called the cable company, they had told me that my signal was fine blah blah, I insisted the guy come out and still look at it so he did and on that day it just decided to run at the advertised speeds. I am running a WNDR 3400 Netgear V1 Router. I have tried changing MTU Size.
View 11 Replies View Related