Linksys Wireless Router :: EA2700 / SE2800 Switch - File Transferring In Connections
Dec 16, 2012
I have a router connected ea2700 on the Internet port to a switch se2800.e switch is connected and everything is gigabit nas. if I try to transfer a file from PC, gigabit ethernet, the transfer rate does not exceed 8 MB/s. if I transfer a file from the NAS to the PC speed is 15 MB/s. the support advised me to change MTU manufacturer parameters,to disable protection,and clone the mac address.the situation has not changed.if I configure the router in bridge mode, the speed is 22MB/s and 45MB/s.
View 3 Replies
ADVERTISEMENT
May 6, 2011
I have a media/storage pc set up in the living room, with my main pc (actually capable of handling the newer 3d content im getting) in the bedroom. All files are downloaded to the Media center pc. I recently changed the download location to drive D to alleviate stress on the operating system drive. Usually when I wanted to transfer files from the Media center to my pc I would go through computer - network - media - location of file. I have found I can't do this to access drive D on the remote Media. Is there a more efficient way than copying files from drive D to C on media just so I can pull them to my main pc? I have tried copying while in remote and pasting on my main pc desktop. It worked great for a 1kb file, but fails every time at 5gb files.
View 2 Replies
View Related
Dec 29, 2011
In my main office, I have a cable modem which is connected to my main E4200 router. All of my equipment (except my Ooma) is served by the E4200. The E4200 broadcasts a wireless network.In my basement, I have a Wii / entertainment center. The E4200 signal from upstairs isn't strong enough to stream video.
I bought the WET610N and have successfully set it up to interact with the E4200 wirelss network. I can hardwire my laptop to the WET610N and verify the internet works greatHowever, the Wii must connect over wireless. I have other equipment in the basement which would benefit from an internet connection. So, I want to A) connect the ESXS88W 10/100 8-port workgroup switch I have to the WET610N *AND* also broadcast a wireless signal in my basement (assuming the wireless network I see in the basement is the same "old" one from upstairs which has not benefited from the WET610N).
How can I set up my WRT54G2 to broadcast a wireless signal in the basement so that it leverages the E4200 signal served by the WET610N, while also having the workgroup switch offer hardwired connections to my other equipment (like Dish Network receiver)? It doesn't seem to work by just plugging the WRT54G2 into the workgroup switch.
View 2 Replies
View Related
Feb 1, 2011
I have a Wrt160n router and a Motorola sb120 modem (provided by comcast after my original modem got fried by lightning, no I didn't have my router hooked up when that happened), I have been having trouble trying to get the modem to send the internet signal to my router. I have tried mac address clone that was suggested on this forum for someone with a different router but still no internet to my computer, its all hooked up through Ethernet cables, the computer I have it hooked up with a hard line is running windows seven. When I plug the modem straight to the computer it works and I have internet but when I hook up the router between them it has no internet.
View 9 Replies
View Related
Aug 9, 2012
I got a refurbished EA4500 (directly from Cisco) last week. I have been having a few issues, which I have found (not too great) workarounds for. However, the latest issue has me stumped, and is unacceptable.Whenever I am transferring files between 2 computers, I get kind of OK speed (5 MB/s). However, while this transfer happens, no other device can connect to the net. Actually, even trying to go to router home page (192.168.1.1) times out.The clients still say they are connected to the router, but I just can't get anywhere.As soon as the file transfer finishes, everything goes back to normal.EA4500 replaced a WRT54G. Never had any problems with that router. It was such a workhorse. Just needed to upgrade to a n-router.I am on the latest non-cloud firmware.I have reduced the MTU size to 1200. Not sure that matters.
View 9 Replies
View Related
Jan 18, 2013
I have an EA3500 and a Windows Vista PC, connected through wireless. When I transfer data from PC to USB shared storage on the router the speed seems normal while it goes awful when I do the opposite. The average speed goes around 200kb/s to be specific. This is unbelievable as it is year 2013.
View 3 Replies
View Related
Dec 11, 2012
I have cable modem coming into the basement hooking up to Linksys Cable Modem (1 yr old). The cat6 line leaves the cable modem and goes approximately 60' through the wall to an Asus-NT66U wireless router on the main floor into the WAN port.I then have a cat6 line go back through that same 60' of wall coming off the LanPort1 of the Asus-NT66U router into a Cisco/Linksys SE2800 8 port gigabit switch (a year old as well).
The problem I am having is as follows. I have been getting intermittent "Unidentified Local Network" problems off an on which I have tried many of the fixes for, evidently unsuccessfully ranging from duplex speed, network ID etc. I had updated the firmware on the NT66U to the latest and am still having problems.
I never have problems with the wireless network which always has connectivity to the internet, however the local is the regular problem. So, to further compound things I have 3 Smart TV's hooked up to the Cisco SE2800 switch over cat6 as well. Those were all working recently until this most recent hiccup and now none of them are working regularly. They can sometimes "see" the wired network and my media server software, but it is intermittent, slow, and never works and often can't see at all.
The TV's are all set to static IP's over the wired network (192.168.1.114/.115/.116) they are the only static IP's out there.The cables are all good and have been repeatedly tested in a variety of ways. All the drivers and firmware are up to date.I think I have a problem with the router/switch communicating and passing through data,The switch does not need a crossover cable, does not seem to have a management menu, and not sure what else to do.
View 2 Replies
View Related
Dec 14, 2011
I have had an e4200 for about a month now and its been pretty good. But I have noticed that it completely locks up when I go to copy mass amounts of data through it. I have a NAS drive plugged into it and my laptop is on the 2.4 spectrum. I went to transfer 8gigs of data from laptop to NAS drive and the entire wireless portion of the router locks up. All my wireless clients drop and I have to unplug the router and plug it back in. Even the 5ghz clients drop as well. I have not tried hardwire, but the main reason I got this was for its throughput.
View 1 Replies
View Related
May 10, 2012
i got an ea2700 and i cant get the external to work internally which i need for server tests now this has worked before on every other router i had without any editing done but this one doest allow that so what can i do to make it work with this router?
View 9 Replies
View Related
Apr 24, 2012
I recently purchased an EA2700 to replace an old Belkin. I ran the set up CD and I am unable to establish an internet connection. I am able to connect to the router (both wired and wireless), ccess the settings, etc but cant reach the net. I've tried turning off the firewall, flushing the DNS, disabledthe IPv6. Did all the basic steps, resett the modem/router, etc...nothing. i hook the Belkin up and it connects just fine
View 9 Replies
View Related
Nov 26, 2012
I have EA2700 Router which support to be a dual-band wireless router and I am trying to connect to my router using 5 Ghz band with AE2500 Dual-Band Wireless-N USB Adapter, I am only seeing 2.4 Ghz wireless band plus even if I manually enter my 5 Ghz SSID my network adapter still wouldn't work on 5 Ghz band. Is there any specific set up in order get 5 Ghz band to work?
View 3 Replies
View Related
Feb 6, 2013
My first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
View 2 Replies
View Related
Apr 30, 2013
i have a EA2700 router and I'm connectied wirelessly to my PS3. If i am not hosting a game i will be lagging all over the place yet it says i have full connection to majority of games that i connect to. i paid 115 dollars for this router and am very dissapointed that its doing this. Also no there is no way for me to connect wired to the router it is to far away. Also i tried bringing my ps3 to my friends house and played on his wireless connection and it worked perfectly so its deffinetly my router.
View 3 Replies
View Related
Mar 15, 2013
EA2700v1 WPS-PIN using 5GHz does not work. This router includes WPS header in its 5GHz beacon and probe response but the router removes the WPS header from them once WPS-PIN starts. There is no problem with WPS-PIN using 2.4GHz.
View 1 Replies
View Related
May 14, 2013
I want to change password in my EA2700 but don't know how to do it. How to change password in EA2700?
Looking for [url]
Find the best [url]
View 1 Replies
View Related
Jan 24, 2013
I am not able to access the web interface of the router.No, i am not using cisco cloud or smartlink .. yes, it has the latest firmware (Ver.1.0.14.129982).Yes, I might be able to get to it if i shut down the router and turn it on again a few minutes later, but the problem is.. why? why do i have to interrupt connections and not have internet to log into the admin web interface of this device? Is there a known problem with it that makes the webservice go down?.. or to take extremely long to respond and thus the browser to quit on it throwing an error?
View 3 Replies
View Related
Mar 19, 2013
Im not able to conect to the internet threw my router, but i am able to with my modem. i dont want to pay for a new one and Cisco wants me to pay $30 for phone support.
View 9 Replies
View Related
Dec 23, 2012
My new EA 2700 disconnects from the internet if the desktop is idle for more than 30 minutes. needs to be unplugged for a few minutes then it will reconnect. This is an unacceptable situation and this thing will be tossed if it cannot be fixed. Can this be reset so it won't disconnect? or do I need to replace it with a product from another company?
View 1 Replies
View Related
Apr 19, 2012
I have an Cisco EA2700 router and a Motorola SB6121 modem. If I'm connected to the router wirelessly or through any of the lan ports, I can't visit the modem's diagnostics page at 192.168.100.1. If I connect directly to the modem, it works fine. Also I cannot ping the modem through the router, just get a timeout. My ISP is Comcast.
View 9 Replies
View Related
Sep 20, 2012
I have tried all the speed test sites and tried downloads with and without my EA2700. Every test shows about half the perfomance when connected through the router. My speed tests at speedtest.net with a direct connection are in the 21-26Mbps range, the same tests run about a minute later through the EA2700 fall in the 10-12Mbps range with spikes up to 17Mbps.I've reset the router and modem.I've gone back to the 1.0.14.129982 Firmware (which it's currently on)I've set the MTU everywhere from 1400 to 1500 (literally EVERY setting for at least a couple of hours) it is 1492 currently. None of these have worked. In addition, when a large stream starts, such as a Steam download, I will lose ALL connectivity. Going in to Network and Sharing and clicking to connect to the internet restores the connection, no need to reset any hardware (which is odd in itself). I have had MANY routers over the years and I've all but exhausted support with service provider as the connection is solid if I eliminate the router.Main machine is a Windows 7 Home edition Total of 5 machines, 3 of which see regular use All machines go through a Trendnet 16 port switch and performance is the same direct or through the switch I m on Brighthouse in Central Florida and have all but exhausted their support.
View 4 Replies
View Related
Sep 11, 2012
I recently bought an EA2700 in hopes that it will make my connection faster, stronger signal and stable. However, this is not the case. The connections keeps dropping and the range is the same as my Verizon-FiOS router. Anyway, I'm hoping that a fix be distributed to address this issue. I can't return my router to the vendor anymore.
Now, since I have two routers, I want to be able to leverage EA2700's dual-band feature and the Guest-access feature but I can't make this as a main router since my FiOS router should still be able to supply IP addresses to my cable boxes, thus, I can't configure it as a Bridge. I'm thinking if I just split the IP distribution as follows:
FiOS router: 192.168.1.2-110
EA2700: 192.168.1.111-150
View 4 Replies
View Related
Feb 7, 2013
I have a linksys EA 2700 with the latest smart wifi firmware. However, the "Release and renew" of the IPv4 internet ip is greyed out. Only IPv6 is enabled.
View 1 Replies
View Related
Dec 31, 2012
went through setup twice, double checked connections, bought new ethernet cable from router to computer, still not connecting. However when i go from my modem to computer i get connected. could i have a faulty router. the router is new from walmart the ea2700.
View 1 Replies
View Related
Feb 2, 2013
Every time after the router (Linksys EA2700) is powered off and restarted, there is no interent access available. The router configuration status reports an Internet Address of 0.0.0.0 and all the devices at home are left with a wifi without Internet access. I have to unplug the WAN from the router and plug it in again while it is turned on to restore internet access (and a normal Internet Address is seen from the status page). The WAN works fine with the routers I had previously. I wonder if I have to perform this every time I power on the router. I have tried resetting the router and reinstalling Cisco Connect but that didn't work.
View 3 Replies
View Related
Nov 13, 2012
I have a EA2700 and will try to reserve an IP address to a PC, but getting up that address is invalid.I already have two reservations, which is 192.168.10.10 and .... 50, I try to reserve ...... 20 but am getting alert that this then is "Invaldi IP".
View 9 Replies
View Related
Feb 24, 2013
I have an EA2700 (fimware "classic" 1.0.14.129982) that used to work perfectly fine with a Comcast cable modem. I just recently switched to Charter with an Arris TM902 modem and that's where the problems started. The cable modem will not recognize my router. I have to plug in a computer into the cable model when it starts up. Then I need to clone the MAC address and restart the router (after disconnecting the computer). Why isn't the cable modem recognizing the router when I restart it? I guess this could work if it would be a one time thing but I had to power-cycle the modem and it stopped recognizing the router even with the cloned MAC address. So I had to do the whole spiel again.
Is there any way to make this work easier? Should I update my router's firmware to the "smart" one?
View 9 Replies
View Related
Aug 24, 2012
I just bought linksys EA2700 to replace my U.S Robotics .. but when i try to connect it like the old router , the internet lights won't turn on, is it because i have to use a modem then use ethernet cable ? can't i just use ADSL cable directly to the router like robotics router ? when i try to configure it manually , i change the internet type to PPoE protocol but i can't find VCI/VPI so where are they ?
View 1 Replies
View Related
May 7, 2013
I have a Cisco outer EA2700 connected using a Lan cable, Lan cable works fine as I connected it directly to my PC, I am unable to access wifi network connection, I am able to search the router and also able to cnnect to the router, But wireless connection shows limited or no connectivity, and unable to access any websites. It was working fine till yesterday, I tried rebootng ad also unplug and replug the network cable also reset the router but does not work
View 1 Replies
View Related
Apr 3, 2013
I have a nest in the house and upgraded my router because nest is very picky with what routers it works with..something to do with power save mode and NAT settings Read here.well the linksys was working just fine with the nest until I upgraded the firmware to the smart wifi thing...it's a EA2700 btw.
View 3 Replies
View Related
Jan 21, 2013
My new router has started to disconnect for a second or so from the internet then reconnect. I have been unable to see the issue and changing the frequency was unsuccessful. This has also been happening when connecting both wired and wirelessly
View 9 Replies
View Related
Jan 26, 2013
I have had my EA2700 for about 6 months now. Have had no problems until about a month ago. One night I could not get the router to connect to the internet. First thoughts were that the cable connection had gone down. When I finally started to trouble shoot I was able to confirm the cable connection is fine by connecting to the modem directly.
Out of the modem I am getting 14+ Mbps. (I only Pay for 10 So a plus there)
I could not get the router to connect to the internet. I ended up resetting the router and reconfiguring it. Ever since then I have been getting really unstable connection to the internet.
When I connect directly to the modem (cabled) I am getting a nice steady connection . When I add the router and hardware in I get a good connection only a Mbps or 2 drop off and a pretty steady connection. Then when I connect over WIFI I get a much larger drop off depending on if the device is a 2.4 or a 5
The connection is extremely unstable. The curve on the graph {URL} is very peaky and has extreme highs and lows. This is multiplied when running on the GHz (as my laptop runs on). My Iphone running on GHz. I can pull down 9 Mbps but the curve is still up and down. Iphone on GHz I barely get Mbps and it is extremely choppy on the graph.
I am able to back this up with my I PAD. I can only confirm the 2.4 number with the laptop as it does not have GHz radio in it. So every thing that us running on the 2.4 is getting poor connections.
I also suspect that the through put on the wired side is poor as well. I am unable to prove it as every test I run shows a good connection but netflix has been locking up and I have to restart what ever I am watching 2 to even 10 times a show. I need to do more testing to be sure the network or the devices are to blame.
View 2 Replies
View Related
Sep 1, 2012
I have century link DSL with a Westell 7500. I bought the EA2700 as a replacement. I assume its not a dsl since there is no phone line connection.
View 2 Replies
View Related
May 3, 2013
I have a domain name which I register to my WAN address so I can do service hosting from my home network. I recently switched out my WRT54G running DDWRT with an EA2700. I set up my port forwards and static dhcp assignments and they are working from outside my network, but when I try any network operation involving my WAN address from my LAN machines, the connections just timeout.
I read in some posts that "you cannot do this" and "you have to test from a remote internet machine". Well, this WORKED with DDWRT, so it's not like it's impossible to make a router that does this. Why can't I do this with the EA2700? Is there some magic setting that will let this work??
The whole point of using a domain name is that I can access my services ANYWHERE using the convenient "name" thing.. genius, right? Except when I bring my laptop home and suddenly my domain goes non-responsive.
View 4 Replies
View Related
