I have a EA2700 and will try to reserve an IP address to a PC, but getting up that address is invalid.I already have two reservations, which is 192.168.10.10 and .... 50, I try to reserve ...... 20 but am getting alert that this then is "Invaldi IP".
View 9 RepliesI have an EA2700 running latest firmware 1.1.38.138827. It is using Cisco Connect Cloud. I am unable to access the DHCP Reservations link under Connectivity/ Local Network. When I click on it, nothing happens. I've tried multiple browsers including IE 10 (Windows 8 RTM), Firefox 15, and Chrome 21. I also tried on a Windows 7 machine with IE 9 and the link doesn't work on that either except that it shows a box that says Invalid Character when I click on the DHCP Reservations link. I see no invalid characters on the screen. Any workaround other than downgrading the firmware or assigning static IPs on individual PCs?Also, on an unrelated note, where is the Dynanic DNS configuration on the Cisco Connect Cloud?
View 8 Replies View RelatedI'm setting up a new E1200 and I'm searching for the area for DHCP reservations. My D-Link DIR-615 offers this ability in the Admin panel. This is quite useful since it allows for easier port forwarding management to specific Machine IPs without having to assign static IPs for each machine. I can't seem to find any documentation on this feature no the site or in the forum that applies to the E1200. If it's not offered, boy did I make a mistake in getting the E1200. I should have bought another DIR-615.
View 2 Replies View RelatedBefore upgrading my firmware on my EA2700, I can easily reserve IP address for my wired device. With the new cloud interface, I click to select the device from the top pane to bring it down in the reserved IP pane below. When I try to save the IP change I get two errors: 1) Invalid characters in the device name 2) Invalid IP address. I get the same errors even if I do not edid not edit the name or IP address.
As for the device name, I did not change anything or rename the device. One device has a " - " in the name and the router was happy with it until I tried to reserve the IP. Another one had a " ' " in the name, same problem again.
My network DHCP range is set to 192.168.1.200 to 192.168.1.250 and I use the range from 192.168.1.1 to 192.168.100 for static IP. When I tried to reserve a static IP below 192.168.1.200, the router say that is an invalid IP.
The workaround to this problem has been to temporary set the DHCP range to 192.168.1.1 to 192.168.1.50 and set the static IP in that range and rename the devices to a name that the EA2700 will accept. Next I move the DHCP range from 192.168.1.50 to 192.168.1.100 and repeat the process. After, all the static IP are assigned, then I can reset the DHCP range to 192.168.1.200 to 192.168.1.250.
This is a pain to do. In the previous (cloud less) version, this was a breeze to do. Also, I have not figured out how to redirect ports with the new interface. Is that progress?
I am running into a DHCP problem on a Cisco 891 running 15.0(1)M2. I am running DHCP on the router and want to reserve an address for a printer. I have done this hundreds of times on hundreds of routers. Per Cisco recommendation, I let the printer lease an address to see whether it uses it's "hardware-address" or "client-id". This printer uses the "hardware-address" format. The printer has leased 10.0.0.102 right off the bat. I want it at 10.0.0.50.
I have a DHCP pool, like this:
ip dhcp pool CLIENT
network 10.0.0.0 255.255.255.0
domain-name chsinc.ds
default-router 10.0.0.1
dns-server 10.0.0.1
lease 2
I create a "reservation" like so:
ip dhcp pool HP_LaserJet_Printer
host 10.0.0.50 255.255.255.0
hardware abcd.ef12.3456
Now I do a "show running-config" to see what I've put in and it looks just like above. Now we reset the network settings or change any network setting on the printer to force it to renew it's lease. What should happen and what usually happens is that the printer should request an IP, be offered 10.0.0.50, accept that IP and come up on that IP address. What is happening with this particular printer is that the printer requests a specific IP (the same IP that it had initially = 10.0.0.102), the router says OK and does not enforce the reservation. Then the router actually deletes the hardware-address config line right out of the running config. A "show running-config" shows that the reservation config now looks like this:
ip dhcp pool HP_LaserJet_Printer
host 10.0.0.50 255.255.255.0
See the logs below. Notice the ones in bold.
000226: Dec 12 17:34:01.382: DHCPD: Seeing if there is an internally specified pool class:
000227: Dec 12 17:34:01.382: DHCPD: htype 1 chaddr 101f.74b0.575c
000228: Dec 12 17:34:01.382: DHCPD: remote id 020a00000ae1e10100000001
000229: Dec 12 17:34:01.382: DHCPD: circuit id 00000000
[code]....
Is there a way to make the router enforce the reservation and not let clients just bring their own IP and actually make changes to the running-config of the router?
how to setup DHCP reservations I found that the ASA 8.x was unable to do it but saw reference that ASA 9 was supposed to have this feature. Looking thru 9 and asdm 7 I'm not seeing how to. I know it just came out but I can't find any official mention of this feature in 9.
View 1 Replies View RelatedWhy is the DHCP Reservations List limited to 25 entries? Is there a beta firmware version that allows more?
View 5 Replies View RelatedI have a DIR-615 router running FW version 3.01 with Hardware Version: C1 , my xbox is wired to my router. When I port forwarded, i had an strict nat, but had the best connection, but not by very much. When i put DMZ on, i had a strict nat, and the connection to other people was a bit better then UPnP.When i had UPnP on i had a open nat, i could barely be able to connect to anyone.what is a DHCP Reservations List?
View 3 Replies View RelatedI have a setup using LogMeIn Hamachi and the network type creates a Windows Bridge. I also use the DHCP Reservations List to assign the same IP to specific devices. Well I have the MAC Address for my NIC in the list which works when I am not using the bridge. When using the bridge, of course the MAC address changes and when I try to add it to the list I get the following message in a popup window. The MAC Address is 02:e0:61:05:45:3e I have tried manually entering it, letting the router enter it from the list of computers and just to rule out something stupid, I have tried changing the letters to upper case and removing the colons.
Another issue I can see when this issue is resolved is that I do not believe it will let me add this reservation since I will be using the same IP used by another reservation. My DGL-4500 allowed this if I had the other reservations using the same IP disabled.Below these comments/rants are some feature requests. I have put them last as some of the requests are explained in the comment/rant section.I have read through this list and I have to say that after I purchased the router, which I ordered on-line, I was dreading it, but I have not had issues. It is possible that I am not using features that cause this issue. I believe the issues occur when using certain configurations with the "Enable Advanced DNS Service" enabled. I am not using this service. Since I knew people were having issue s with it, I wanted to see my results leaving that out. I have had this router running since a week before Christmas and I have many Virtual Server entires, QoS and port forwarding entries, https based remote administration, both 5GHz and 2.4GHz networks enabled supporting a/b/g/n(on both networks) and a guest network enabled on both bands all supporting WPA (TKIP and AES). I have 2 Giga wired connections that are always active, a 100Mb connection that is on an off but used almost daily, 2 Laptops that use the 2.4GHz network daily and one is 802.11g 54Mb and the other is 802.11n 150Mb and they are on at the same time almost daily, a printer that is on and used multiple times a week that uses 802.11g and a game system that uses 802.11a this device is used daily. Most devices are on and used at the same time daily and we have a good deal of regular Internet traffic and moderate other network traffic during these times. At night all computers are backed up over the network and most of the other network devices are off or not during this time. Other than having to reboot my Internet hardware provided by my ISP, I have not had issues. The router has been rebooted for config changes and I usually cycle it when I cycle the Internet hardware. Point is, so far no issues, good performance and it works and I have of course had other devices connected using the guest network and I have been testing features, performance, etc.
What's up with having so much variation in how features work across routers?e.g. My DHCP Reservation issue above. This router does not work with a setup like my DGL-4500.This router allows a preset amount of services like QoS and Virtual Server entries while the DGL-4500 just lets you add entries. Now maybe there is a limit and it just looks like there is no limit. Of course, there is at least a limit that is reached when you have used a certain amount of memory with the configuration.so many routers while leaving gaps and the lack of feature explanation and comparison?I switched to this router because I wanted a dual band setup which my DGL-4500 does not provide. That leads to the issue of the new way D-Link deals with dual-band. When I purchased the router it did not list that you had to choose 2.4GHz or 5GHz or it is not simultaneous dual-band. I was duped because I used to install DWL-7100AP for people that needed better wireless options for home businesses and small businesses and that provides simultaneous dual-band and back then if it was dual-band it was simultaneous. But I am disappointed in some of the features lost like WISH support and a few options here and there which do not seem like they are specific to gaming routers and this router is more on the mid range and low high range end of consumer, prosumer, home business and lower traffic small business routers, so why is it missing these features and why does it have the limitations I listed in the "variation in how features work" section above?
Other examples of lack of feature clarity are with Game Fuel, HD FUEL and Intelligent QoS. Isn't Game Fuel Intelligent QoS of some sort. Now from the example provided in the overview for the DGL-4500, Game Fuel optimizes game performance, but it does not say this is automatic or if it works along with the rules you set in the Game Fuel section which is the same as the QoS Engine section in the DIR-825. The difference is that the DIR-825 has a "Enable QoS Engine" option while the DGL-4500 has an "Enable Game Fuel" option. It seems that Intelligent QoS does what Game Fuel does, but expands that to VOIP, Media Streaming, etc. and it may be more automatic. HD Fuel in the only place I have seen it mentioned seems to refer to the combination of Intelligent QoS and the inclusion of 5GHz wireless support. Of course there is no version and feature documentation and in fact while the overview of the DIR-825 talks about gaming with Intelligent QoS, but if you bring up a comparison of routers, the chart has no in the gaming section for the DIR-825. I can't say I have noticed better or worse gaming performance with the DIR-825 compared with the DGL-4500, but given the shear lack of documentation on how to use Game Fuel and Intelligent QoS properly, who knows if I have this setup correctly. I will say the QoS Engine section in the DIR-825 is easier to use than the Game Fuel section in the DGL-4500.
1) The ability to reduce the brightness of the status lights, set them to solid if enabled with brightness options and to set them to off with an option to have some very faint light to show that the router is on. Of course I should be able to set different options to be applied at specific times.
2) Add the applicable features missing from the DIR-825 that are found in the DGL-4500 and applicable features from other routers. Also, get them all so they work the same on each router and let get the best from them all and make that the standard. e.g. In my DHCP reservation example above don't set the standard to the limitations of the DIR-825, but make the DGL-4500 function set or better function set of all routers combined for each feature the standard with-in router categories. e.g. the DIR-825, DGL-4500 and DIR-855 would be in the high end router category for consumer, prosumer, home business and lower traffic small business routers.
3) For DHCP reservations, you should not be limited to the DHCP IP Address Range.
4) On the log-in screen, get a better captcha and fix the tab order.
5) Add a log-out option in the web interface.
6) Allow for a next hop option in the DCHP server section. It would be cool, if there could be a list of IPs allows one to be enabled at a time.
7) Allow different DHCP server settings for each network. There are 5 on the DIR-825. Wired, 2.4GHz regular, 2.4GHz Guest, 5GHz regular and 5GHz Guest. Would be nice if you could set a couple of VLANs on the Ethernet ports and then have different DHCP setings for each VLAN.
For guest wireless networks, allow rules to be set to allow access to certain services on the network. E.g. I may want to allow printing. So allow a single port or multiple ports with easy settings for consecutive port ranges to be opened to an IP, IP range or all IPs and allow all ports for an IP or range of IPs. Of course, leave the allow full access option.
8a) Allow users to set rule sets that can be enabled/disabled like the full access option.
8b) Allow a control that can be set in the rule sets that controls if the wireless devices can talk to each other and another that controls if they can access devices on the wired network and another that controls if the wireless devices can access the Internet.
8c) Allow rules above to be limited to be applied to specific MAC Addresses.
8d) These options would be good to have for the non-guest wireless networks and wired network as well.
This is on a DIR-655, firmware 2.01NA, hardware rev B1.Is there a limit on the number of DHCP reservations that can be added to this WAP?This WAP was working fine with 10 DHCP reservations (wired & wireless devices), 6 schedules, Access control of 2 devices by MAC (6 defined, only 2-3 active at a time).I started adding additional DHCP reservations, because I'm simplifiying my network, and when I add the 26th DHCP reservation I get the message "Schedule rules is Full! Please Delete an Entry."
I've been adding all of the new DHCP reservations as disabled, but I haven't assigned any schedules or otherwise to these new devices yet. So what's up with this message??
1. To specify static IPs for components on my network, is it simply a matter of reserving each component in the DHCP Reservations List portion of the Network Settings page?
2. On the same page, in the DHCP Server Settings portion, if Enable DHCP Server : is deselected, does this mean that only the hosts specified in the DHCP Reservations List can access the network? In other words, is access now restricted to these entries?
3. If the DIR-615 is powered OFF, will the above settings, etc. be lost (similar to a reset)?
I have an ASA 5540 cluster that is configured as my remote access VPN point. Users connect using IPSEC Profiles with Cert based authentication, the profile is configured to query two DHCP servers (infoblox appliance servers).
The problem I am encountering, is that I need to make reservations on the DHCP server for some users for specific business needs. What happens is that the ASA passes the request to the DHCP server with it's own MAC address and not the MAC of the remote host.
Is there any way I can configure the ASA to pass the request using the hosts actual MAC address?
I'm having troubles with this firmware in a SG300-28 switch. Actually the DHCP server, a new feature in this firmware release, doesn't work correctly. DHCP static reservations are not working: CLient ID and MAC address are not recognized correctly, and the DHCP server assigns the first free IP in the pool, rather than the reserved one.If Cisco engineers read this, plese correct the issue.
View 5 Replies View Relatedi got an ea2700 and i cant get the external to work internally which i need for server tests now this has worked before on every other router i had without any editing done but this one doest allow that so what can i do to make it work with this router?
View 9 Replies View RelatedI recently purchased an EA2700 to replace an old Belkin. I ran the set up CD and I am unable to establish an internet connection. I am able to connect to the router (both wired and wireless), ccess the settings, etc but cant reach the net. I've tried turning off the firewall, flushing the DNS, disabledthe IPv6. Did all the basic steps, resett the modem/router, etc...nothing. i hook the Belkin up and it connects just fine
View 9 Replies View RelatedI have EA2700 Router which support to be a dual-band wireless router and I am trying to connect to my router using 5 Ghz band with AE2500 Dual-Band Wireless-N USB Adapter, I am only seeing 2.4 Ghz wireless band plus even if I manually enter my 5 Ghz SSID my network adapter still wouldn't work on 5 Ghz band. Is there any specific set up in order get 5 Ghz band to work?
View 3 Replies View RelatedMy first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
i have a EA2700 router and I'm connectied wirelessly to my PS3. If i am not hosting a game i will be lagging all over the place yet it says i have full connection to majority of games that i connect to. i paid 115 dollars for this router and am very dissapointed that its doing this. Also no there is no way for me to connect wired to the router it is to far away. Also i tried bringing my ps3 to my friends house and played on his wireless connection and it worked perfectly so its deffinetly my router.
View 3 Replies View RelatedEA2700v1 WPS-PIN using 5GHz does not work. This router includes WPS header in its 5GHz beacon and probe response but the router removes the WPS header from them once WPS-PIN starts. There is no problem with WPS-PIN using 2.4GHz.
View 1 Replies View RelatedI want to change password in my EA2700 but don't know how to do it. How to change password in EA2700?
Looking for [url]
Find the best [url]
I am not able to access the web interface of the router.No, i am not using cisco cloud or smartlink .. yes, it has the latest firmware (Ver.1.0.14.129982).Yes, I might be able to get to it if i shut down the router and turn it on again a few minutes later, but the problem is.. why? why do i have to interrupt connections and not have internet to log into the admin web interface of this device? Is there a known problem with it that makes the webservice go down?.. or to take extremely long to respond and thus the browser to quit on it throwing an error?
View 3 Replies View RelatedIm not able to conect to the internet threw my router, but i am able to with my modem. i dont want to pay for a new one and Cisco wants me to pay $30 for phone support.
View 9 Replies View RelatedMy new EA 2700 disconnects from the internet if the desktop is idle for more than 30 minutes. needs to be unplugged for a few minutes then it will reconnect. This is an unacceptable situation and this thing will be tossed if it cannot be fixed. Can this be reset so it won't disconnect? or do I need to replace it with a product from another company?
View 1 Replies View RelatedI have an Cisco EA2700 router and a Motorola SB6121 modem. If I'm connected to the router wirelessly or through any of the lan ports, I can't visit the modem's diagnostics page at 192.168.100.1. If I connect directly to the modem, it works fine. Also I cannot ping the modem through the router, just get a timeout. My ISP is Comcast.
View 9 Replies View RelatedI have tried all the speed test sites and tried downloads with and without my EA2700. Every test shows about half the perfomance when connected through the router. My speed tests at speedtest.net with a direct connection are in the 21-26Mbps range, the same tests run about a minute later through the EA2700 fall in the 10-12Mbps range with spikes up to 17Mbps.I've reset the router and modem.I've gone back to the 1.0.14.129982 Firmware (which it's currently on)I've set the MTU everywhere from 1400 to 1500 (literally EVERY setting for at least a couple of hours) it is 1492 currently. None of these have worked. In addition, when a large stream starts, such as a Steam download, I will lose ALL connectivity. Going in to Network and Sharing and clicking to connect to the internet restores the connection, no need to reset any hardware (which is odd in itself). I have had MANY routers over the years and I've all but exhausted support with service provider as the connection is solid if I eliminate the router.Main machine is a Windows 7 Home edition Total of 5 machines, 3 of which see regular use All machines go through a Trendnet 16 port switch and performance is the same direct or through the switch I m on Brighthouse in Central Florida and have all but exhausted their support.
View 4 Replies View RelatedI recently bought an EA2700 in hopes that it will make my connection faster, stronger signal and stable. However, this is not the case. The connections keeps dropping and the range is the same as my Verizon-FiOS router. Anyway, I'm hoping that a fix be distributed to address this issue. I can't return my router to the vendor anymore.
Now, since I have two routers, I want to be able to leverage EA2700's dual-band feature and the Guest-access feature but I can't make this as a main router since my FiOS router should still be able to supply IP addresses to my cable boxes, thus, I can't configure it as a Bridge. I'm thinking if I just split the IP distribution as follows:
FiOS router: 192.168.1.2-110
EA2700: 192.168.1.111-150
I have a linksys EA 2700 with the latest smart wifi firmware. However, the "Release and renew" of the IPv4 internet ip is greyed out. Only IPv6 is enabled.
View 1 Replies View Relatedwent through setup twice, double checked connections, bought new ethernet cable from router to computer, still not connecting. However when i go from my modem to computer i get connected. could i have a faulty router. the router is new from walmart the ea2700.
View 1 Replies View RelatedEvery time after the router (Linksys EA2700) is powered off and restarted, there is no interent access available. The router configuration status reports an Internet Address of 0.0.0.0 and all the devices at home are left with a wifi without Internet access. I have to unplug the WAN from the router and plug it in again while it is turned on to restore internet access (and a normal Internet Address is seen from the status page). The WAN works fine with the routers I had previously. I wonder if I have to perform this every time I power on the router. I have tried resetting the router and reinstalling Cisco Connect but that didn't work.
View 3 Replies View RelatedI have an EA2700 (fimware "classic" 1.0.14.129982) that used to work perfectly fine with a Comcast cable modem. I just recently switched to Charter with an Arris TM902 modem and that's where the problems started. The cable modem will not recognize my router. I have to plug in a computer into the cable model when it starts up. Then I need to clone the MAC address and restart the router (after disconnecting the computer). Why isn't the cable modem recognizing the router when I restart it? I guess this could work if it would be a one time thing but I had to power-cycle the modem and it stopped recognizing the router even with the cloned MAC address. So I had to do the whole spiel again.
Is there any way to make this work easier? Should I update my router's firmware to the "smart" one?
I just bought linksys EA2700 to replace my U.S Robotics .. but when i try to connect it like the old router , the internet lights won't turn on, is it because i have to use a modem then use ethernet cable ? can't i just use ADSL cable directly to the router like robotics router ? when i try to configure it manually , i change the internet type to PPoE protocol but i can't find VCI/VPI so where are they ?
View 1 Replies View RelatedI have a Cisco outer EA2700 connected using a Lan cable, Lan cable works fine as I connected it directly to my PC, I am unable to access wifi network connection, I am able to search the router and also able to cnnect to the router, But wireless connection shows limited or no connectivity, and unable to access any websites. It was working fine till yesterday, I tried rebootng ad also unplug and replug the network cable also reset the router but does not work
View 1 Replies View RelatedI have a nest in the house and upgraded my router because nest is very picky with what routers it works with..something to do with power save mode and NAT settings Read here.well the linksys was working just fine with the nest until I upgraded the firmware to the smart wifi thing...it's a EA2700 btw.
View 3 Replies View Related