D-Link DIR-825 :: DHCP Reservations List Limit?

Nov 23, 2010

Why is the DHCP Reservations List limited to 25 entries?  Is there a beta firmware version that allows more?

View 5 Replies


ADVERTISEMENT

D-Link DIR-615 :: Formation Regarding DHCP Reservations List?

Jan 2, 2012

I have a DIR-615 router running FW version 3.01 with Hardware Version: C1 , my xbox is wired to my router. When I port forwarded, i had an strict nat, but had the best connection, but not by very much. When i put DMZ on, i had a strict nat, and the connection to other people was a bit better then UPnP.When i had UPnP on i had a open nat, i could barely be able to connect to anyone.what is a DHCP Reservations List?

View 3 Replies View Related

D-Link DIR-825 :: DGL-4500 MAC Address In DHCP Reservations List

Jan 13, 2010

I have a setup using LogMeIn Hamachi and the network type creates a Windows Bridge. I also use the DHCP Reservations List to assign the same IP to specific devices. Well I have the MAC Address for my NIC in the list which works when I am not using the bridge. When using the bridge, of course the MAC address changes and when I try to add it to the list I get the following message in a popup window. The MAC Address is 02:e0:61:05:45:3e I have tried manually entering it, letting the router enter it from the list of computers and just to rule out something stupid, I have tried changing the letters to upper case and removing the colons.

Another issue I can see when this issue is resolved is that I do not believe it will let me add this reservation since I will be using the same IP used by another reservation. My DGL-4500 allowed this if I had the other reservations using the same IP disabled.Below these comments/rants are some feature requests. I have put them last as some of the requests are explained in the comment/rant section.I have read through this list and I have to say that after I purchased the router, which I ordered on-line, I was dreading it, but I have not had issues. It is possible that I am not using features that cause this issue. I believe the issues occur when using certain configurations with the "Enable Advanced DNS Service" enabled. I am not using this service. Since I knew people were having issue s with it, I wanted to see my results leaving that out. I have had this router running since a week before Christmas and I have many Virtual Server entires, QoS and port forwarding entries, https based remote administration, both 5GHz and 2.4GHz networks enabled supporting a/b/g/n(on both networks) and a guest network enabled on both bands all supporting WPA (TKIP and AES). I have 2 Giga wired connections that are always active, a 100Mb connection that is on an off but used almost daily, 2 Laptops that use the 2.4GHz network daily and one is 802.11g 54Mb and the other is 802.11n 150Mb and they are on at the same time almost daily, a printer that is on and used multiple times a week that uses 802.11g and a game system that uses 802.11a this device is used daily. Most devices are on and used at the same time daily and we have a good deal of regular Internet traffic and moderate other network traffic during these times. At night all computers are backed up over the network and most of the other network devices are off or not during this time. Other than having to reboot my Internet hardware provided by my ISP, I have not had issues. The router has been rebooted for config changes and I usually cycle it when I cycle the Internet hardware. Point is, so far no issues, good performance and it works and I have of course had other devices connected using the guest network and I have been testing features, performance, etc.

What's up with having so much variation in how features work across routers?e.g. My DHCP Reservation issue above. This router does not work with a setup like my DGL-4500.This router allows a preset amount of services like QoS and Virtual Server entries while the DGL-4500 just lets you add entries. Now maybe there is a limit and it just looks like there is no limit. Of course, there is at least a limit that is reached when you have used a certain amount of memory with the configuration.so many routers while leaving gaps and the lack of feature explanation and comparison?I switched to this router because I wanted a dual band setup which my DGL-4500 does not provide. That leads to the issue of the new way D-Link deals with dual-band. When I purchased the router it did not list that you had to choose 2.4GHz or 5GHz or it is not simultaneous dual-band. I was duped because I used to install DWL-7100AP for people that needed better wireless options for home businesses and small businesses and that provides simultaneous dual-band and back then if it was dual-band it was simultaneous. But I am disappointed in some of the features lost like WISH support and a few options here and there which do not seem like they are specific to gaming routers and this router is more on the mid range and low high range end of consumer, prosumer, home business and lower traffic small business routers, so why is it missing these features and why does it have the limitations I listed in the "variation in how features work" section above?

Other examples of lack of feature clarity are with Game Fuel, HD FUEL and Intelligent QoS. Isn't Game Fuel Intelligent QoS of some sort. Now from the example provided in the overview for the DGL-4500, Game Fuel optimizes game performance, but it does not say this is automatic or if it works along with the rules you set in the Game Fuel section which is the same as the QoS Engine section in the DIR-825. The difference is that the DIR-825 has a "Enable QoS Engine" option while the DGL-4500 has an "Enable Game Fuel" option. It seems that Intelligent QoS does what Game Fuel does, but expands that to VOIP, Media Streaming, etc. and it may be more automatic. HD Fuel in the only place I have seen it mentioned seems to refer to the combination of Intelligent QoS and the inclusion of 5GHz wireless support. Of course there is no version and feature documentation and in fact while the overview of the DIR-825 talks about gaming with Intelligent QoS, but if you bring up a comparison of routers, the chart has no in the gaming section for the DIR-825. I can't say I have noticed better or worse gaming performance with the DIR-825 compared with the DGL-4500, but given the shear lack of documentation on how to use Game Fuel and Intelligent QoS properly, who knows if I have this setup correctly. I will say the QoS Engine section in the DIR-825 is easier to use than the Game Fuel section in the DGL-4500.

1) The ability to reduce the brightness of the status lights, set them to solid if enabled with brightness options and to set them to off with an option to have some very faint light to show that the router is on. Of course I should be able to set different options to be applied at specific times.

2) Add the applicable features missing from the DIR-825 that are found in the DGL-4500 and applicable features from other routers. Also, get them all so they work the same on each router and let get the best from them all and make that the standard. e.g. In my DHCP reservation example above don't set the standard to the limitations of the DIR-825, but make the DGL-4500 function set or better function set of all routers combined for each feature the standard with-in router categories. e.g. the DIR-825, DGL-4500 and DIR-855 would be in the high end router category for consumer, prosumer, home business and lower traffic small business routers.

3) For DHCP reservations, you should not be limited to the DHCP IP Address Range.

4) On the log-in screen, get a better captcha and fix the tab order.

5) Add a log-out option in the web interface.

6) Allow for a next hop option in the DCHP server section. It would be cool, if there could be a list of IPs allows one to be enabled at a time.

7) Allow different DHCP server settings for each network. There are 5 on the DIR-825. Wired, 2.4GHz regular, 2.4GHz Guest, 5GHz regular and 5GHz Guest. Would be nice if you could set a couple of VLANs on the Ethernet ports and then have different DHCP setings for each VLAN.

For guest wireless networks, allow rules to be set to allow access to certain services on the network. E.g. I may want to allow printing. So allow a single port or multiple ports with easy settings for consecutive port ranges to be opened to an IP, IP range or all IPs and allow all ports for an IP or range of IPs. Of course, leave the allow full access option.

8a) Allow users to set rule sets that can be enabled/disabled like the full access option.

8b) Allow a control that can be set in the rule sets that controls if the wireless devices can talk to each other and another that controls if they can access devices on the wired network and another that controls if the wireless devices can access the Internet.

8c) Allow rules above to be limited to be applied to specific MAC Addresses.

8d) These options would be good to have for the non-guest wireless networks and wired network as well.

View 15 Replies View Related

D-Link DIR-615 :: Hosts Specified In DHCP Reservations List Can Access Network?

May 1, 2011

1. To specify static IPs for components on my network, is it simply a matter of reserving each component in the DHCP Reservations List portion of the Network Settings page?

2. On the same page, in the DHCP Server Settings portion, if Enable DHCP Server : is deselected, does this mean that only the hosts specified in the DHCP Reservations List can access the network? In other words, is access now restricted to these entries?

3. If the DIR-615 is powered OFF, will the above settings, etc. be lost (similar to a reset)?

View 6 Replies View Related

D-Link DIR-655 :: Schedule Rules Is Full / When Adding DHCP Reservations

Feb 19, 2012

This is on a DIR-655, firmware 2.01NA, hardware rev B1.Is there a limit on the number of DHCP reservations that can be added to this WAP?This WAP was working fine with 10 DHCP reservations (wired & wireless devices), 6 schedules, Access control of 2 devices by MAC (6 defined, only 2-3 active at a time).I started adding additional DHCP reservations, because I'm simplifiying my network, and when I add the 26th DHCP reservation I get the message "Schedule rules is Full! Please Delete an Entry."

I've been adding all of the new DHCP reservations as disabled, but I haven't assigned any schedules or otherwise to these new devices yet. So what's up with this message??

View 12 Replies View Related

Linksys Wireless Router :: EA2700 Unable To Access DHCP Reservations Link Under Connectivity / Local Network

Sep 7, 2012

I have an EA2700 running latest firmware 1.1.38.138827. It is using Cisco Connect Cloud. I am unable to access the DHCP Reservations link under Connectivity/ Local Network. When I click on it, nothing happens. I've tried multiple browsers including IE 10 (Windows 8 RTM), Firefox 15, and Chrome 21. I also tried on a Windows 7 machine with IE 9 and the link doesn't work on that either except that it shows a box that says Invalid Character when I click on the DHCP Reservations link. I see no invalid characters on the screen. Any workaround other than downgrading the firmware or assigning static IPs on individual PCs?Also, on an unrelated note, where is the Dynanic DNS configuration on the Cisco Connect Cloud?

View 8 Replies View Related

Cisco Firewall :: DHCP Reservations With ASA 9

Nov 15, 2012

how to setup DHCP reservations I found that the ASA 8.x was unable to do it but saw reference that ASA 9 was supposed to have this feature. Looking thru 9 and asdm 7 I'm not seeing how to. I know it just came out but I can't find any official mention of this feature in 9.

View 1 Replies View Related

D-Link DIR-655 :: Can't Find Computer In DHCP List

Apr 19, 2011

i had the dir-655 with desktops and laptops running with xp and win 7, also some other devices such as ipod, iphone, ps3, xbox, problem occura with conflict of network ip address, i think xp and win 7 both login with the same network ip address.  So I start to disconnect every device and try to connect each desktop and laptops, one by one, enabled the DHCP and reserve the network ip to avoid conflict.  But here's the problem, when I connect the first computer with wired to the dir-655, can't find the computer in the DHCP list so I cannot do the reserve, I'm able to surf internet even I can see info with ipconfig.  So I connected 1 wired and 2 wifi to the network, only 1 wifi network ip showing on the list, so I reserve that one, but after I refresh, the DHCP list is empty.

View 1 Replies View Related

D-Link DIR-825 :: Sometimes Shows A DHCP Reservation List

Mar 5, 2012

Ever since I updated my firmware to 1.01 my web interface for the network settings screen has been random. Somtimes it shows a DHCP reservation list, sometimes it doesn't. Sometimes there are reservations, sometimes there are selectable radio buttons.  I guess I'm just trying to figure out if this is a firmware issue or not. Ever since I updated the firmware it has been flakey.... But I was having issues with other stuff before that. When there are no reservations, sometimes i can't even select any computers because there aren't any in the drop down, when all of my hardware is online?

View 6 Replies View Related

Linksys Wireless Router :: DHCP Reservations On E1200?

Feb 8, 2012

I'm setting up a new E1200 and I'm searching for the area for DHCP reservations. My D-Link DIR-615 offers this ability in the Admin panel. This is quite useful since it allows for easier port forwarding management to specific Machine IPs without having to assign static IPs for each machine. I can't seem to find any documentation on this feature no the site or in the forum that applies to the E1200. If it's not offered, boy did I make a mistake in getting the E1200. I should have bought another DIR-615.

View 2 Replies View Related

Linksys Wireless Router :: EA2700 DHCP Reservations Invalid IP?

Nov 13, 2012

I have a EA2700 and will try to reserve an IP address to a PC, but getting up that address is invalid.I already have two reservations, which is 192.168.10.10 and .... 50, I try to reserve ...... 20 but am getting alert that this then is "Invaldi IP".

View 9 Replies View Related

Cisco VPN :: Configuring DHCP Reservations For VPN Users Terminating On ASA 5540

Mar 7, 2011

I have an ASA 5540 cluster that is configured as my remote access VPN point. Users connect using IPSEC Profiles with Cert based authentication, the profile is configured to query two DHCP servers (infoblox appliance servers).
 
The problem I am encountering, is that I need to make reservations on the DHCP server for some users for specific business needs. What happens is that the ASA passes the request to the DHCP server with it's own MAC address and not the MAC of the remote host.
 
Is there any way I can configure the ASA to pass the request using the hosts actual MAC address?

View 1 Replies View Related

Cisco Switches :: SG300 DHCP Static Reservations Are Not Working

May 19, 2013

I'm having troubles with this firmware in a SG300-28 switch. Actually the DHCP server, a new feature in this firmware release, doesn't work correctly. DHCP static reservations are not working: CLient ID and MAC address are not recognized correctly, and the DHCP server assigns the first free IP in the pool, rather than the reserved one.If Cisco engineers read this, plese correct the issue.

View 5 Replies View Related

Cisco Switching/Routing :: 891 Router DHCP Server Reservations Being Overridden?

Dec 11, 2012

I am running into a DHCP problem on a Cisco 891 running 15.0(1)M2.  I am running DHCP on the router and want to reserve an address for a printer.  I have done this hundreds of times on hundreds of routers.  Per Cisco recommendation, I let the printer lease an address to see whether it uses it's "hardware-address" or "client-id".  This printer uses the "hardware-address" format.  The printer has leased 10.0.0.102 right off the bat.  I want it at 10.0.0.50.
 
I have a DHCP pool, like this:
 
ip dhcp pool CLIENT
   network 10.0.0.0 255.255.255.0
   domain-name chsinc.ds
   default-router 10.0.0.1
   dns-server 10.0.0.1
   lease 2
 
I create a "reservation" like so:
 
ip dhcp pool HP_LaserJet_Printer
   host 10.0.0.50 255.255.255.0
   hardware abcd.ef12.3456
 
Now I do a "show running-config" to see what I've put in and it looks just like above.  Now we reset the network settings or change any network setting on the printer to force it to renew it's lease.  What should happen and what usually happens is that the printer should request an IP, be offered 10.0.0.50, accept that IP and come up on that IP address.  What is happening with this particular printer is that the printer requests a specific IP (the same IP that it had initially = 10.0.0.102), the router says OK and does not enforce the reservation.  Then the router actually deletes the hardware-address config line right out of the running config.  A "show running-config" shows that the reservation config now looks like this:
 
ip dhcp pool HP_LaserJet_Printer
   host 10.0.0.50 255.255.255.0
 
See the logs below.  Notice the ones in bold.
 
000226: Dec 12 17:34:01.382: DHCPD: Seeing if there is an internally specified pool class:
000227: Dec 12 17:34:01.382:   DHCPD: htype 1 chaddr 101f.74b0.575c
000228: Dec 12 17:34:01.382:   DHCPD: remote id 020a00000ae1e10100000001
000229: Dec 12 17:34:01.382:   DHCPD: circuit id 00000000

[code]....

Is there a way to make the router enforce the reservation and not let clients just bring their own IP and actually make changes to the running-config of the router?

View 6 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8968 - DHCP Client List Is Incorrect?

Dec 3, 2012

Region : France
Model : TD-W8968
Hardware Version : V1
Firmware Version : TD-W8968_V1_120926
ISP : SFR
Device in question: siemans C610 IP voip phone
Configuration:

* The C610 is directly connected to TD W8968 via the ethernet port number 3 >> ethernet port number 1 is connected to the devolo homeplug 200AVPLUS . The PC is at the other end of the homeplug network

* The DHCP address starts at 192.168.1.100 - 192.168.1.199.

Symptom:

1. It takes a long time (about 2-3 minutes) for the C610IP to obtain the IP address of 192.168.1.100 after the synchronisation of the ADSL line is finished 2. In the DHCP client list, I could only see the IP address of the PC (192.168.1.101) but not the C610 IP. However, if I type 192.168.1.100, I could access to the configuration page of the C610 IP. - I only managed to see the C610IP once in the DHCP client list.

I tried to unplug -> replug the router but to no avail.

View 2 Replies View Related

TP-Link Dual-Band Wireless :: DHCP Client List Customization On WDR4300?

Dec 6, 2012

Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Comcast

So I've been checking my router DHCP list and I usually use the WPS feature to add devices. I know how many devices I have and which ones are wireless etc. I've made address reservations on all the devices that I have and know of. One feature that really frustrates me (which is missing) is no way to rename a device. My iPhone is named: Reggie's iPhone yet the 4300 picks it up as Unknown... I dont understand why. I've renamed it on the iPhone to different things and restarted it but still it comes up as that. I have 2 Nexus 7s and both come up with wierd names, one is for my wife and one is for me and I wish there was a way to name it proper.

Question is: Will the name edit feature ever get added to it? I dont get why it's not there now, it's not really something major (I have a 5 year old router that even has that... and it cant even support N). It's really frustrating to have to guess and check the devices on my network because most of them come up as unknowns.

Right now I'm trying to located another device that's coming up as unknown and now matter how much I try, since the router lacks any feature to assist finding it, it's really frustrating.

something else i noticed: my DHCP List shows all the devices connected with their IP addresses, yet I went into CMD and was doing a random ping command. I'm able to ping 192.168.0.114 with perfect stats back yet on my DHCP List it shows the highest IP is at 192.168.0.112.... Is something wrong here? Is it supposed to not pick up the IPs it gives out? And of course since there isnt a way to tell if that IP is for a WIFI or ethernet device, I have no idea what that device is...

yet i found another ip address on my network by using the ping command. actually I went ahead and did arp -a to find out all the ips with mac addresses. this is a serious flaw with the security of this router!!

View 2 Replies View Related

Computer Not Showing Up In DHCP Client List?

Feb 9, 2011

I just started having this problem yesterday. I was experiencing weird downloading/internet browsing issues and couldn't figure out what the problem was. I started looking around my router settings and noticed that in my DHCP Client list, my computer isn't in it. The router is hooked up to the computer, so it's not wireless. My phone and my girlfriend's laptop are listed, but the main computer isn't. It's especially causing problems with port forwarding. Downloads will stop because the port isn't showing as open. I'm running 64 bit Windows 7 and a Belkin N+ Wireless Router, model F5D8235-4.Firmware is up to date.

View 6 Replies View Related

Belkin F5D7230-4 How To Clear Dhcp List

Feb 8, 2011

Is there any way to clear the archived DHCP list on the Belkin F5D7230-4 wireless router? Over the years there have been a lot of connections, most are no longer around but the Belkin holds on to the list. I can find no way to clear it to get it back to what is currently connected. I have tried a soft reboot, unplugging power etc but it seems like I will have to do a factory reset and apart from not being able to find my ADSL login details, I would have to reset all my settings.

View 2 Replies View Related

Cisco Wireless :: How To Know If 4400 Has Limit On DHCP Leases

Mar 4, 2012

i have a controller that has mutliple dhcp scopes and should in theory give out close to a thousand plus addresses. But i have seen wireless users not getting addresses once the controller has leased about 490 ip adds. My controller is on 7.XX version.

View 3 Replies View Related

Cisco Firewall :: 881 - Limit All Traffic Except DHCP To Self Zone?

Dec 22, 2009

On router Cisco 881 with ZBF I have dedicated VLAN for AP connection. AP is getting IP address from router dhcp server, I would like to limit all access to Router "Self" zone to only DHCP traffic if possible. How to limit all traffic except DHCP to self zone?What ever I do to traffic to/from self zone I must always specify last statement as "class class-default/inspect" and not drop as I would like to. 

View 5 Replies View Related

Unknown IP Address Range On Router DHCP Client List

Nov 19, 2011

I keep getting some additional IP addresses logging onto my home network that have an address outside what should be allowed by the router. The server is running at 192.168.2.1 and is set to only allow clients from 192.168.2.2 - 192.168.2.10 so a total of 9 clients should be allowed on.The problem is that something keeps logging in with an address of 192.168.169.2 or 3 etc. Sometimes more than one device at a time.I have assumed that it is some automated or virtual client as I'm pretty certain my network has not been breached. I have a 9 character password with a relatively random alphanumeric combination, although I haven't tried changing the password (I live in a share house with with a bunch of devices using wireless, so I haven't yet bothered). What I don't understand is how it has connected with the xx.xx.169.xx range at all. I have a Belkin 'Share' Wireless N Modem Router and at some stage there was a 'guest' network but that has since been disabled and I still am seeing the extra address. I have attached a screen shot of the DHCP client list on the router.The following is a list of devices that may be on the network at times, I'm thinking one of these may be responsible for the problem:

Windows Vista Desktop - Only LAN device
PS3
Macbook
Epson wireless printer
Android HTC Desire Mobile Phone
Laptops running various Windows versions (XP, Vista and 7)

A few thoughts I had:

- the android phone is capable of running a wireless hotspot, may have to look into it to see if if has been operating as an access point into the Belkin router, but assumed this wouldn't bring up clients connected to the phone on the home router.

- The desktop has PS3 Media server installed to stream video to the PS3 over the network (not that I have ever managed to get it to work), however this is not ever open on the desktop.

View 10 Replies View Related

Linksys Wireless Router :: Finding DHCP List In Admin For WRT160N?

Jan 5, 2012

I have the WRT160N router for 3.5 yrs and it's worked perfectly since installing it. About two weeks ago it began intermittently dropping cable connection. First few times I thought I could resolve it by unplugging/plugging router & modem so they can "re-syn" to the cable connection. That still works but now it occurs sometimes multiple times within a few minutes/hours and then won't happen again for an entire day/days. The other day I had connectivity but instead of the usual 5 bars I only had 3 while  using my laptop in the same spot in the house as usual.

View 5 Replies View Related

Linksys Wireless Router :: E2500 DHCP Client List Not Showing

Aug 25, 2011

I have purchased E2500 and i am having following problems:
 
1. DHCP client list not showing - only shows when i reboot the router. After some time, the list never shows even when i press refresh button
2. I can only reserve IP when i reboot the router - after some time i cannot do this action also
 
I have upgraded to latest firmware and also peformed reset as directed by support.

View 1 Replies View Related

Belkin Routers :: F5D8236-4 V2 - DHCP Client List Is Not Showing All IP Addresses In Use

Feb 23, 2013

I have a Wireless N router model F5D8236-4 v2 (01) with firmware 2.00.04 (Nov 12 2008 10:51:08) and it's not showing all issued wireless or Wired IP addresses in DHCP Client List.

They all have IP addresses and connect to the internet through the router, but in the router administration page, they're not listing. The Windows devices all show but most of the Mac devices are not, nor is my XBox 360.

My reason for investigating this is because the router seems to keep losing the Mac devices and a router reboot fixes it, but it shouldn't have this problem because all the Windows devices just seem to work.

According to the support page I have the latest available (dated November 12, 2008 which really seems kinda old to me for a Wireless N router). Are there any plans for a new firmware offering for this modem or have you already deprecated it as "legacy equipment"?

View 1 Replies View Related

Linksys Wireless Router :: E4200v1 Get A List Of DHCP Clients On Guest Network

Jul 3, 2012

I've got an E4200v1 running 1.0.04 firmware with guest access enabled. I'd like to find out who is logged in using the guest access. Is there a way to get a list of the DHCP clients on the guest network? I'm able to do this for the non-guest access via the WEB interface's Status->Local Network->DHCP Clients Table page. But I can't find a similar table for the guest network.

View 3 Replies View Related

D-Link DIR-655 :: DHCP Turned Off As ASA 5500 Is Providing DHCP

May 30, 2011

I have a Cisco ASA 5500 as the main router with a DIR-655 as a wireless access point behind it.  DHCP is turned off on the 655 as the ASA is providing DHCP.  This worked great for about a year and now suddenly, without any changes, I'm having problems.  The only thing that connects without a problem is a laptop, which shows up on the device list with an IP.  Other devices have problems.  iPhones connect, show an IP on the device itself, but when listed in the connected list on the 655 show no IP.  The connection is super slow.  An Airport Express will connect, but again, shows no IP in the connected list on the 655.  Using the ethernet cable from the Airport Express, nothing can get an IP.  I can live with the iPhone not connecting, but the Airport Express not connecting is a major problem.  Any reason why this would just stop working one day?

View 2 Replies View Related

Linksys Cable / DSL :: X2000 DHCP Client Table Failed To Show Client List

Apr 21, 2013

Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.

View 4 Replies View Related

D-Link DIR 635 Not Showing Up In List Of Networks?

Jan 25, 2011

I have problems with my D-Link DIR 635 router. It shows up fine in list of networks on my girlfriends Mac and on my new laptop, but on my older laptop it doesnt show up at all (whereas a lot of other networks do). Seeing as my current laptop is being repaired at the moment, I need to be able to connect to the net with my old laptop too.

I run Windows XP Professional on my laptop, which is a Compaq Presario f700. why the network doesnt show up?

View 3 Replies View Related

D-Link DIR-655 :: No Next Page On Forum List

Jan 17, 2011

It's kinda hard to keep "peckin" at the small numbers to go to the next page.Put this post where ever it needs to go but since I am in DIR-655, I put it here, because it's TOO AGGRAVATING to find the NEXT page.

View 2 Replies View Related

D-Link DIR-615 :: How To Limit Speed On Some Computers

May 15, 2011

i recently bought the dir-615, and i have 4 computers connected to it, 2 desktops with ethernet cables and 2 laptops with wifi. I want to know how to limit the internet speed on some computers, because i sometimes need full speed on my desktop. Is it possible within the router configuration interface?

View 1 Replies View Related

D-Link DIR-600 :: Limit Bandwidth On Router?

Jul 12, 2011

How can I limit the bandwidth of a router (DIR 600).

View 1 Replies View Related

D-Link DIR-615 :: Download Speed Limit

Jul 11, 2011

I bought my d-link 615 a few days ago and managed to connect it to my network and so on but I have a problem when it comes to my download speed. My usual speed is somewhere between 7.5-8 mb/s but when I have the router installed it's limited to 5 mb/s. Do you know why this might be happening?

View 14 Replies View Related

D-Link DIR-655 :: List Of Changes For The Latest Firmware Version?

Jan 8, 2011

Where the list of changes for the latest firmware version can be found?  My new DIR-655 has firmware from May 2010, and I see the latest and greatest on the DLINK website is from September.  But it doesn't state what the changes are, so I'm not sure if I should upgrade or not.

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved