D-Link DIR-655 :: DHCP Turned Off As ASA 5500 Is Providing DHCP
May 30, 2011
I have a Cisco ASA 5500 as the main router with a DIR-655 as a wireless access point behind it. DHCP is turned off on the 655 as the ASA is providing DHCP. This worked great for about a year and now suddenly, without any changes, I'm having problems. The only thing that connects without a problem is a laptop, which shows up on the device list with an IP. Other devices have problems. iPhones connect, show an IP on the device itself, but when listed in the connected list on the 655 show no IP. The connection is super slow. An Airport Express will connect, but again, shows no IP in the connected list on the 655. Using the ethernet cable from the Airport Express, nothing can get an IP. I can live with the iPhone not connecting, but the Airport Express not connecting is a major problem. Any reason why this would just stop working one day?
View 2 Replies
ADVERTISEMENT
Dec 15, 2012
I've got a DIR-655 that I use as a wireless access point/switch (dhcp off) behind my Actiontec Verizon Fios router. The DIR-655 is in the basement and has my PS3 and Xbox hard wired to it.I've got playon server setup on my pc upstairs which is connected wireless to the Actiontec router. If I connect my ps3 wirelessly to the Actiontec, it immediately sees the playon server and streams movies without issue. However, when I hardwire the PS3 to the DIR-655, it will not pickup the playon server connected to the Actiontec router.I've got dhcp turned off and multicasting turned on under advanced settings of the Dlink.
View 5 Replies
View Related
Mar 12, 2011
I have a ASA 5505 that I have been using for a while, but a new ISP is trying to configure my service so that the outside interface has to be configured as DHCP to receive a reserved IP address, and then they will route a separate, non-contiguous block of addresses to that address.
Essentially, they have a DHCP reservation for 1.2.3.4 for my ASA, and then they have 10.2.3.16/28 as a separate block routed to me.
Obviously, I can do my static NAT translations using outside as the address, but I cannot get the separate block of addresses to route through the ASA. Is there a way to do this and get them to work? My ASA is running 7.2(2)
View 3 Replies
View Related
Apr 5, 2012
Here is where I want to go:
Windows server 2008 (providing DHCP and DNS) 192.168.89.1 on all
Cisco SG 300-20 (switch) 192.168.89.3
all Clients(15 x DHCP assigned IPs) connected to switch
WRT300N(192.168.89.2) connected to switch
Internet modem connected to WRT300N
To achieve this I need to disable DHCP on the WRT300N, since my server is providing DHCP.The issue I have is that when I disable DHCP at the WRT300N, I lose internet connection (connected to either switch or direclty to WRT300N).
View 6 Replies
View Related
Mar 17, 2013
i have a simple router on a stick config which is providing dhcp to a customer SSID. however i don't want employees to stay on it and eat the band width since its open. the lease is set to an hour, is there anyway that i could set it so that once your lease expired it can't be renewed for 4 about 8 hours? I am using a cisco 2600 router in this setup.
View 1 Replies
View Related
Dec 15, 2011
I have an ASA 5500 series and am looking to set up the AnyConnect VPN. Looking at this guide everything seems fairly straightforward. However, on the inside private network DHCP is setup and I was wondering if it was possible to just use DHCP instead of providing a static address pool? I did not see any option to do this.
View 1 Replies
View Related
Sep 30, 2011
Can the DHCP server on an ASA be configured with static bindings like IOS routers can?
View 2 Replies
View Related
Jun 10, 2013
We assign in our IPSec VPN the tunnel-address from our centralized dhcp server pools.In the profile we have two server's ip configured.In test (whireshark) we noticed that the discover always go to the first configured ip.
I do not understand and could not finf hints how the function is.
- backup server with a timeout when no answer comes from primary ?
- should ASA do simultaneous discover to all configured ip's ?
=>Problem is, that although the first server not answered in a timely manner, we noticed no discover to the second.
Here the partial CLI - Config:
++
tunnel-group AZInt07 type remote-access
tunnel-group AZInt07 general-attributes
authentication-server-group ActivPack
default-group-policy AZInt
dhcp-server 10.x.x.y
dhcp-server 10.x.y.y
[code].....
View 3 Replies
View Related
Jul 2, 2012
While configuring a 5500 wireless controller, i came across this option of DHCP proxy under Advanced tab of Controller Option.It asks for the dhcp option 82 remote id format & the dhcp timeout.
1. What is the significance of this & when do we use it?
2. Also, under each wlan ssid that we create, there is an option of dhcp address required under the advanced tab. Do we need to use this option, if we are defining a normal dhcp pool in our controller for that ssid.
View 3 Replies
View Related
Oct 30, 2012
with our WLC 5500 controller, once the clients get the DHCP address the page is not redirecting them to the guest portal.What is the best way to check as to why the redirection is failing.
View 8 Replies
View Related
Nov 11, 2012
I have some DHCP trouble since I subnetted my network with a 2921. My clinets are in 172.16.2.0/23 and DHCP servers are in 172.16.5.0/24.Sometimes, randomly I guess, I get NACK from my DHCP server, and if I look into DHCP logs I got something like this:
15,11/09/12,09:52:27,NACK,172.16.3.172,switchE51D12.host.com,A0CF5BE51D12,,0,6,,,,,,,,
15,11/09/12,09:52:28,NACK,172.16.3.172,switchE51D12.host.com,A0CF5BE51D12,,0,6,,,,,,,,
15,11/09/12,09:52:29,NACK,172.16.3.172,switchE51D12.host.com,A0CF5BE51D12,,0,6,,,,,,,,
[code]....
View 6 Replies
View Related
Apr 3, 2012
Have a client wanting to hand out public ip addresses to all clients from a PFSense Firewall terminating the internet connection.
How do I allow the Cisco Switches currently in place, configured with private ip addresses in the 10.10.x.x ranges and Vlans, where the main 3550 layer 3 has defined dhcp scopes for each vlan, to relay dhcp requests from all vlans to the PFSense firewall?
I assume I would take off the currently defined dhcp scopes for the vlans and configure each vlan/switch with the ip helper address and specify the PFSense firewall and that Nat would have to be disabled onthe firewall?
View 1 Replies
View Related
Aug 2, 2011
When I go into the Network Settings, and the end of the page I find a list named "Number of Dynamic DHCP clients: 7". As far as I know, I should only see 4, all 4 laptops; however, I see 2 UNKNOWN entries in this list, and one name "Macondo". Each of these entries have an option (a link) saying "Revoke" and other "Reserve". I am just wonder if these entries are intruders in my home network. What should I do? I am afraid to break my internet connection. By the way, I set up every single one of my family 4 laptops at home with a WPA-PSK using a very long key.
View 9 Replies
View Related
Jan 6, 2013
I've just discovered this thing in Windows Event log. The DHCP-Client log is full with this: the client received a NAK from the DHCP Server. Strangely, they still get the desired IP address. (Which are reserved adresses for the MAC adresses.)So I've looked at the logs in the DIR-615 (rev.D, FW: 4.13), and found this:
View 1 Replies
View Related
Apr 20, 2012
Signed up for Sonic Fusion, received ZTE 831 modem in bridge mode, DHCP off.
Have tried many variations of D-Link settings with WAN DHCP and it just does not get an IP address from the ISP. Unicast on/off, DNS relay on/off, SPI on/off, etc.
With the modem settings unchanged, can plug cable from PC directly into modem. It gets an ISP DHCP and works fine. DNS and internet access work, can surf google.com.
Have an Airlink AR525W wireless router. When it is set to DHCP WAN, it also "just works" when plugged into the DSL modem. It is using the router MAC, did NOT clone the MAC from my PC. The Airlink LAN IP is 192.168.1.1, same as the D-Link. The copy-paste from the Airlink configuration screen:
Connection Type: Automatic Configuration - DHCP
Internet IP Address: 173.228.4.46
Subnet Mask: 255.255.255.0
Default Gateway: 173.228.4.1
DNS 1: 208.201.224.11
DNS 2: 208.201.224.33
DNS 3: 0.0.0.0
MTU: Auto
The D-Link was working fine with ATT DSL and PPPoE (this is in SF Bay Area, 94022), but extremely frustrating that it does not seem work to with Sonic DHCP. Called Sonic support, and was able to confirm that plugging the PC directly into the modem works fine. So it seems there is a problem with the DIR-825 (or configuration of it).
View 6 Replies
View Related
Oct 24, 2011
My router is stuck in a loop. At connection time of 1min39, the dhcp release button presses donw by itself. It does that continually, non-stop. It won't show me as a dhcp client yet i have internet access.
View 1 Replies
View Related
Feb 26, 2011
I recently upgraded from a WRT54G and am having issues with a Win7 PC with wireless-N. Initially I had it configured static at 192.168.100.100 and everything worked, but the speeds were miserable (I followed all the forum posts and recommended settings). I noticed in the Status section of the router pages that the system showed up with the correct MAC address, but the IP showed as 192.168.100.10, which is the same as the router. Assuming this might be causing issues, I set a reservation for the system at .100 and set the client to use DHCP. However, now it won't pull an IP address at all. The status pages show the client with the correct MAC address, but an IP of 0.0.0.0. I've verified the MAC address a dozen times and rebooted the router and the client dozens of times with no change. Even when I removed the reservation, the system won't pick up an IP. I have a wireless-G client that's pulling an IP fine, so I know it's sort of working. The wired LAN is working fine, too. There are no IP conflicts, either. I changed DHCP to 'Always Broadcast (compatibility for some DHCP clients), but no change there, either. The client sees the network and still has a good signal, but just won't grab an IP.
I'm running Hardware Version: B1 / Firmware Version: 2.01NA
View 2 Replies
View Related
May 27, 2012
My DIR 655 is refusing to act like a router and more like a normal switch. Anything involving the router side of things(DHCP,firewall,wireless, etc) does not work.
Basically when it powers up the blue power light comes on and that's it. If I plug my cable modem into the wan port then this light comes on with nothing else. If I then proceed to plug a cable into Lan 1 I get the address of my cable modem assigned to my computer and all internet access is fine. As opposed to being assigned an address from the router's DHCP. If I plug a cable from another router into any of the lan ports on the DIR 655 then I get assigned addresses from that router's DHCP and all internet access is routed through.
View 1 Replies
View Related
Jun 17, 2011
I have an Avaya IP Phone for work. This has been tested at work and works as expected. After the IP Phone boots it's able to obtain an IP address from work. At home when I plug the IP phone into my DIR-655 router, it's unable to obtain an IP address. Other network devices are able to obtain an IP address, for example any computer or laptop. Also my wireless works with no issues expect for the IP phone. I've already done some searching and found other users with the same issue but I haven't been able to find a solution other than setting a static IP address. I'm curious why this relatively new router won't work with an IP phone. I've played with some of the router settings but it didn't make a difference. Any work around to get the DHCP to work? I'm running the latest firmware for my router: 1.35A Hardware Versions: A4.
View 9 Replies
View Related
Nov 23, 2010
Why is the DHCP Reservations List limited to 25 entries? Is there a beta firmware version that allows more?
View 5 Replies
View Related
Jan 18, 2011
I have disabled the internal DHCP/DNS server in the routers firmware. I have enabled the wireless guest access SSID. A client associating with the Guest Wireless Access will obtain a DHCP address from the server in the LAN zone, but cannot resolve DNS as the firewall prevents traffic to flow from the Guest zone to the LAN zone, as it should.Is there a way to enable the DHCP server and DNS server in the routers firmware, but only on the Guest Zone? Is it possible to get the Guest Zone to have a different subnet?Tech support has hung up on me twice now.
View 5 Replies
View Related
Dec 7, 2011
I am trying out a DAP-1513 unit but there is no forum section for this? My question seems to be general and might cover the other models also. Do the DHCP request, from the attached LAN devices on the DAP, get pass to the DHCP "server?"
View 6 Replies
View Related
Jan 2, 2012
I have a DIR-615 router running FW version 3.01 with Hardware Version: C1 , my xbox is wired to my router. When I port forwarded, i had an strict nat, but had the best connection, but not by very much. When i put DMZ on, i had a strict nat, and the connection to other people was a bit better then UPnP.When i had UPnP on i had a open nat, i could barely be able to connect to anyone.what is a DHCP Reservations List?
View 3 Replies
View Related
Apr 19, 2011
i had the dir-655 with desktops and laptops running with xp and win 7, also some other devices such as ipod, iphone, ps3, xbox, problem occura with conflict of network ip address, i think xp and win 7 both login with the same network ip address. So I start to disconnect every device and try to connect each desktop and laptops, one by one, enabled the DHCP and reserve the network ip to avoid conflict. But here's the problem, when I connect the first computer with wired to the dir-655, can't find the computer in the DHCP list so I cannot do the reserve, I'm able to surf internet even I can see info with ipconfig. So I connected 1 wired and 2 wifi to the network, only 1 wifi network ip showing on the list, so I reserve that one, but after I refresh, the DHCP list is empty.
View 1 Replies
View Related
Mar 5, 2012
Ever since I updated my firmware to 1.01 my web interface for the network settings screen has been random. Somtimes it shows a DHCP reservation list, sometimes it doesn't. Sometimes there are reservations, sometimes there are selectable radio buttons. I guess I'm just trying to figure out if this is a firmware issue or not. Ever since I updated the firmware it has been flakey.... But I was having issues with other stuff before that. When there are no reservations, sometimes i can't even select any computers because there aren't any in the drop down, when all of my hardware is online?
View 6 Replies
View Related
Jan 31, 2011
I have a DIR-655 (RevA) which I have been very happy with when used with a broadband wireless ISP. We just recently obtained Frontier DSL and I want to use my already configured DIR-655 with the new service. I have successfully bridged the Westell 7500 DSL modem provided by Frontier (DHCP server turned off, mode set to bridge-bridge.) I tested this by attaching a laptop and verifying that it was assigned a WAN IP address and that I could ping resources on the Internet.
When I attach the DLink and start it up, it gets a WAN address and everything looks good, but I can not ping (from the router) to any resource on the Internet (by IP address), including the assigned gateway. It goes without saying that computers attached to the DIR-655 are also unable to ping addresses on the Internet. Oh, I have cloned the Westell modem's MAC address to the DLink router as well.
Any special settings in the DIR-655 that are required to work with Frontier/Verizon's DSL network? Or compatibility issues? and I've updated to the 1.35NA firmware.
View 11 Replies
View Related
Jan 13, 2010
I have a setup using LogMeIn Hamachi and the network type creates a Windows Bridge. I also use the DHCP Reservations List to assign the same IP to specific devices. Well I have the MAC Address for my NIC in the list which works when I am not using the bridge. When using the bridge, of course the MAC address changes and when I try to add it to the list I get the following message in a popup window. The MAC Address is 02:e0:61:05:45:3e I have tried manually entering it, letting the router enter it from the list of computers and just to rule out something stupid, I have tried changing the letters to upper case and removing the colons.
Another issue I can see when this issue is resolved is that I do not believe it will let me add this reservation since I will be using the same IP used by another reservation. My DGL-4500 allowed this if I had the other reservations using the same IP disabled.Below these comments/rants are some feature requests. I have put them last as some of the requests are explained in the comment/rant section.I have read through this list and I have to say that after I purchased the router, which I ordered on-line, I was dreading it, but I have not had issues. It is possible that I am not using features that cause this issue. I believe the issues occur when using certain configurations with the "Enable Advanced DNS Service" enabled. I am not using this service. Since I knew people were having issue s with it, I wanted to see my results leaving that out. I have had this router running since a week before Christmas and I have many Virtual Server entires, QoS and port forwarding entries, https based remote administration, both 5GHz and 2.4GHz networks enabled supporting a/b/g/n(on both networks) and a guest network enabled on both bands all supporting WPA (TKIP and AES). I have 2 Giga wired connections that are always active, a 100Mb connection that is on an off but used almost daily, 2 Laptops that use the 2.4GHz network daily and one is 802.11g 54Mb and the other is 802.11n 150Mb and they are on at the same time almost daily, a printer that is on and used multiple times a week that uses 802.11g and a game system that uses 802.11a this device is used daily. Most devices are on and used at the same time daily and we have a good deal of regular Internet traffic and moderate other network traffic during these times. At night all computers are backed up over the network and most of the other network devices are off or not during this time. Other than having to reboot my Internet hardware provided by my ISP, I have not had issues. The router has been rebooted for config changes and I usually cycle it when I cycle the Internet hardware. Point is, so far no issues, good performance and it works and I have of course had other devices connected using the guest network and I have been testing features, performance, etc.
What's up with having so much variation in how features work across routers?e.g. My DHCP Reservation issue above. This router does not work with a setup like my DGL-4500.This router allows a preset amount of services like QoS and Virtual Server entries while the DGL-4500 just lets you add entries. Now maybe there is a limit and it just looks like there is no limit. Of course, there is at least a limit that is reached when you have used a certain amount of memory with the configuration.so many routers while leaving gaps and the lack of feature explanation and comparison?I switched to this router because I wanted a dual band setup which my DGL-4500 does not provide. That leads to the issue of the new way D-Link deals with dual-band. When I purchased the router it did not list that you had to choose 2.4GHz or 5GHz or it is not simultaneous dual-band. I was duped because I used to install DWL-7100AP for people that needed better wireless options for home businesses and small businesses and that provides simultaneous dual-band and back then if it was dual-band it was simultaneous. But I am disappointed in some of the features lost like WISH support and a few options here and there which do not seem like they are specific to gaming routers and this router is more on the mid range and low high range end of consumer, prosumer, home business and lower traffic small business routers, so why is it missing these features and why does it have the limitations I listed in the "variation in how features work" section above?
Other examples of lack of feature clarity are with Game Fuel, HD FUEL and Intelligent QoS. Isn't Game Fuel Intelligent QoS of some sort. Now from the example provided in the overview for the DGL-4500, Game Fuel optimizes game performance, but it does not say this is automatic or if it works along with the rules you set in the Game Fuel section which is the same as the QoS Engine section in the DIR-825. The difference is that the DIR-825 has a "Enable QoS Engine" option while the DGL-4500 has an "Enable Game Fuel" option. It seems that Intelligent QoS does what Game Fuel does, but expands that to VOIP, Media Streaming, etc. and it may be more automatic. HD Fuel in the only place I have seen it mentioned seems to refer to the combination of Intelligent QoS and the inclusion of 5GHz wireless support. Of course there is no version and feature documentation and in fact while the overview of the DIR-825 talks about gaming with Intelligent QoS, but if you bring up a comparison of routers, the chart has no in the gaming section for the DIR-825. I can't say I have noticed better or worse gaming performance with the DIR-825 compared with the DGL-4500, but given the shear lack of documentation on how to use Game Fuel and Intelligent QoS properly, who knows if I have this setup correctly. I will say the QoS Engine section in the DIR-825 is easier to use than the Game Fuel section in the DGL-4500.
1) The ability to reduce the brightness of the status lights, set them to solid if enabled with brightness options and to set them to off with an option to have some very faint light to show that the router is on. Of course I should be able to set different options to be applied at specific times.
2) Add the applicable features missing from the DIR-825 that are found in the DGL-4500 and applicable features from other routers. Also, get them all so they work the same on each router and let get the best from them all and make that the standard. e.g. In my DHCP reservation example above don't set the standard to the limitations of the DIR-825, but make the DGL-4500 function set or better function set of all routers combined for each feature the standard with-in router categories. e.g. the DIR-825, DGL-4500 and DIR-855 would be in the high end router category for consumer, prosumer, home business and lower traffic small business routers.
3) For DHCP reservations, you should not be limited to the DHCP IP Address Range.
4) On the log-in screen, get a better captcha and fix the tab order.
5) Add a log-out option in the web interface.
6) Allow for a next hop option in the DCHP server section. It would be cool, if there could be a list of IPs allows one to be enabled at a time.
7) Allow different DHCP server settings for each network. There are 5 on the DIR-825. Wired, 2.4GHz regular, 2.4GHz Guest, 5GHz regular and 5GHz Guest. Would be nice if you could set a couple of VLANs on the Ethernet ports and then have different DHCP setings for each VLAN.
For guest wireless networks, allow rules to be set to allow access to certain services on the network. E.g. I may want to allow printing. So allow a single port or multiple ports with easy settings for consecutive port ranges to be opened to an IP, IP range or all IPs and allow all ports for an IP or range of IPs. Of course, leave the allow full access option.
8a) Allow users to set rule sets that can be enabled/disabled like the full access option.
8b) Allow a control that can be set in the rule sets that controls if the wireless devices can talk to each other and another that controls if they can access devices on the wired network and another that controls if the wireless devices can access the Internet.
8c) Allow rules above to be limited to be applied to specific MAC Addresses.
8d) These options would be good to have for the non-guest wireless networks and wired network as well.
View 15 Replies
View Related
Feb 9, 2012
First of all i do not have that much know how within this field (Although i work for an ISP)
There seems to be a problem with my DIR-655.
#1. As we speak the router is taking down and setting up the connection about 1-2 times pr. minute! the connection uptime is stuck in a infinite loop: 1.12 sec, 1.13, 1.14 and back to 1.12 sec. It comes back from time to time. but this is the second time this have happened.
[Code].....
View 14 Replies
View Related
Aug 12, 2011
I have been using the subject Wireless Router for more than 2 years. Most of the time it worked OK but lately it has been giving issues. [code] Due to a recent power outage, I had to reset the setting on the Dlink router. One of the issue is after resetting the Internet options and rebooting the router when I go back to the system screen, both the Release and Renew buttons are greyed out.I have tried to reboot the router as well as cable modem without any success. The Cable Modem is Motorola SB5120.
View 3 Replies
View Related
Mar 9, 2012
I think, the device's DHCP server can not be configured as expected.
My plan was to set the following preferences:
DHCP IP Address Range: 192.168.100.1 to 254
Default Subnet Mask: 255.255.0.0
Default Gateway: 192.168.0.1
Default Wins: 192.168.0.1
Default DNS: 192.168.0.1
But all I get is the error message, if I try to save these settings: The start host id of lease pool should be small than the end host id.
View 5 Replies
View Related
Nov 20, 2011
I have two DIR-615 devices, I want use first device for main AP and DHCP server and PPPoE . And use second device for Repeater.
How to work WPS and Push button on this device.
View 6 Replies
View Related
Dec 7, 2012
I have a D-Link DGL-4500 Wireless N Gaming Router. If I create a mobile hotspot with my BB Bold 9900, can I somehow get my router to connect to it so I can provide bandwidth to my Ethernet dependent network devices?
View 2 Replies
View Related
Dec 28, 2010
DGL-4100
-> Wii
-> X360
-> PS3
-> DGS-2205 (gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522
We're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. Also, the DGL-4100 doesn't list it under the DHCP clients, but as I've got the DAP-1522 set to a static IP of 192.168.1.50.
View 1 Replies
View Related
