D-Link DIR-655 :: DHCP / Firewall And Wireless Does Not Work
May 27, 2012
My DIR 655 is refusing to act like a router and more like a normal switch. Anything involving the router side of things(DHCP,firewall,wireless, etc) does not work.
Basically when it powers up the blue power light comes on and that's it. If I plug my cable modem into the wan port then this light comes on with nothing else. If I then proceed to plug a cable into Lan 1 I get the address of my cable modem assigned to my computer and all internet access is fine. As opposed to being assigned an address from the router's DHCP. If I plug a cable from another router into any of the lan ports on the DIR 655 then I get assigned addresses from that router's DHCP and all internet access is routed through.
View 1 Replies
ADVERTISEMENT
Mar 5, 2012
On my new E4200v2, after I tried to move beyond the disappointment of Cisco removing Internet Access Policy entirely, I decided to give the stripped down Parental Controls a try.
Sadly, I didn't have any luck doing what I needed to do... block my Tivo's from accessing Youtube.
I enabled Parental Controls, Added the Target Devices (my Tivo's did show up), and added "Youtube.com" as blocked site #1. Saved. Entered the parental password when prompted. Even rebooted the router.
But Youtube wasn't blocked. So I added to the target list a non-Tivo device (a Macbook) for a reality check, and rebooted the router again... still no luck. Youtube still not blocked.
So then I started to wonder if their Parental Control depends somehow on the local DHCP server & Client list. Because my E4200 has DHCP Server = OFF (I have always used a Windows Server for DHCP).
I tried to call Linksys support to get this working, but after 45 mins, including escalation to senior engineer, they really were pretty useless (no real familiariarity with my problem) then they disconnected my call!
View 7 Replies
View Related
Jun 7, 2011
I have the e4200 and I am having trouble getting DHCP reservation to work properly with my Windows 7 machines. Perhaps there is a step that I am missing. Basically I go to the DHCP reservation setup page, select my machine and add it to the reservation table. Then I save the changes. As soon as I do this my computer goes offline. If I reboot my machine, it is still offline. I've tried the same procedure to reserve the IP address for my phone and it works fine so I wonder if the problem is with Win7.
View 6 Replies
View Related
May 30, 2011
I have a Cisco ASA 5500 as the main router with a DIR-655 as a wireless access point behind it. DHCP is turned off on the 655 as the ASA is providing DHCP. This worked great for about a year and now suddenly, without any changes, I'm having problems. The only thing that connects without a problem is a laptop, which shows up on the device list with an IP. Other devices have problems. iPhones connect, show an IP on the device itself, but when listed in the connected list on the 655 show no IP. The connection is super slow. An Airport Express will connect, but again, shows no IP in the connected list on the 655. Using the ethernet cable from the Airport Express, nothing can get an IP. I can live with the iPhone not connecting, but the Airport Express not connecting is a major problem. Any reason why this would just stop working one day?
View 2 Replies
View Related
Jun 17, 2012
how to configure dhcp relay agent and how it's work
View 1 Replies
View Related
May 24, 2012
I am connecting a uc320w to sbs2011 - and having the server do the dhcp - but the Cisco box can't connect to the wan - but it's been fine before I set changed the topology - do I need a static ip address for the wan
View 1 Replies
View Related
Sep 15, 2012
Here my network.dsl provider-->d-link modem (dhcp server, 192.168.1.1)-->X2000 (dhcp replay, 192.168.2.1(LAN IP))--> My laptop - X2000 config: dhcp replay: 192.168.1.1, LAN1 from d-link to WAN x2000 (blue rj45), X2000 have ip address from d-link. but my laptop can not receive ip address. X2000 is not gateway modem because it stuck after 1 day work. Can access to Web config page and internet.
View 4 Replies
View Related
Sep 2, 2011
I'm trying to set up my DIR-655 so I can use VPN to access my work PC. How can I set this up?
View 2 Replies
View Related
Nov 19, 2011
I have a DIR-655 B1 router. The firmware is 2.00 NA. Just to clarify, the DSi itself does work with WPA, but the games only work with WEP. I made a guest account and set it to WEP and it still does not work. I have tried making the main connection WEP as well, but when I go on the game and try it, it says it is WPA and not WEP. My friend has a DIR-655 as well, but the hardware and firmware version are different. Her games work flawlessly.
View 10 Replies
View Related
Jan 8, 2013
We have been using a dhcp and tftp server to automatically configure branch WAN routers such as 1751's and 1841's for years but, have recently purchased a 1921 and 1941 as possible next generation replacements. The problem is when the 1900 series power up instead of getting a dhcp address directions to the tftp server it boots up and asks for the user name to be immediately changed or you will be "locked out". Any workaround to this so that I can again go back to download my common configuration? Or any other way of automatically configuring the newer version ios? Doing extra steps for 500 WAN branch routers is time consuming. Doing configurations without automation for that many is moving in the wrong direction.
View 1 Replies
View Related
Jan 18, 2011
I have disabled the internal DHCP/DNS server in the routers firmware. I have enabled the wireless guest access SSID. A client associating with the Guest Wireless Access will obtain a DHCP address from the server in the LAN zone, but cannot resolve DNS as the firewall prevents traffic to flow from the Guest zone to the LAN zone, as it should.Is there a way to enable the DHCP server and DNS server in the routers firmware, but only on the Guest Zone? Is it possible to get the Guest Zone to have a different subnet?Tech support has hung up on me twice now.
View 5 Replies
View Related
Aug 10, 2011
The DIR-825 wireless simply doesn't work. When I called tech support, we cleared some settings and hard-powered the unit on/off and it finally turned on the wireless radio. A couple weeks later I pull out my laptop to use in the house via wireless and the wireless on the DIR-825 is OFFLINE AGAIN...fallen and it can't get UP.Is anyone having issues with keeping their wireless online? OK - powered it off for 5 minutes...now the wireless is working. I think changing configuration settings causes the thing to lock up.
View 1 Replies
View Related
Mar 22, 2013
Region : Germany
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
I bought 2 router but WDS wont work. If i set on both WDS on they wont connect themselves wireless statics show 0 stations if i only set one to wds then there is one station connectet but it only functionates in one way. I set WDS on router A on and plug a lan cable to my pc i can configure Router B if i plug in B my lan cable i cant configure router A. If i plug my existing network on B and mein PC on A in then i can config all my router in the network but inet wont work -.- what did i false? or have they a disfunction? I tried it withouth wlan security and with wpa2 no succes
View 8 Replies
View Related
Jan 28, 2010
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies
View Related
Jun 15, 2012
i have both 932L and 942L and the 932L was plug N Play and no problem setting up with my WiFi. But i can't get the 942L to work. Works fine with the Ethernet cable but not wireless.
Come on ... I can't be the only one with this problem? I have two 942L cameras and neither one of them can I get connected to the wireless network.
View 3 Replies
View Related
Feb 11, 2012
With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies
View Related
Oct 8, 2012
i have a strange problem in my campus network.im trying to run port security on my access switches which they are 3550 with ios c3550-ipservicesk9-mz.122-52.SE when i run the port security with Sticky option, even i put 1000 mac address for just learning on the port but when i issue the switchport port-security command every pc connected to that port loses its connection with network UNTIL i enable dhcp snooping!!! all my client are getting they ip address from DHCP server but strange thing is that how on earth i have to enable DHCP snooping to port security work properly? also when i check the configuration under the interface when dhcp snooping is not yet enabled switch doesnt add any mac address under the interface so no one can work until i enable snooping and then switch adds mac addresses under the interface configuration.is this Bug on this version of IOS?[code]
View 4 Replies
View Related
May 10, 2012
A friend of mine has given me a D-link DIR-615 Wireless Router. I only have a copper 10 meg ADSL service. The Router Internet socket is an RJ45, the ADSL Filters are RJ11. Is it possible to get this router to work on an ADSL Filter ? Can you get ADSL Filters with both an RJ45 and BT Phone connection on them, or a converter lead which converts RJ45 to RJ11 to work on the current ADSL filter?
View 5 Replies
View Related
Jun 4, 2011
So just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
View 1 Replies
View Related
Jun 2, 2012
I was searching a lot , but I couldn't find any good example, how to configure DHCP server for our wireless clients on Cisco Autonomous AP. I'm looking for example how to configure Dot 11 radios and BVI interfaces.
I have no problem to configure DHCP server on BVI 1 and VLAN 1 ( native VLAN ) interfaces, but there is a problem with other BVI's and VLANs. Maybe this feature isn't supported? Maybe DHCP server feature is supported to work just with default BVI and native VLAN?
View 4 Replies
View Related
Nov 15, 2012
Region : Thailand
Model : TD-W8961ND
Hardware Version : V1
Firmware Version : 2.0.0 Build 111111 Rel.1111
ISP : 3bb
I have a problem when I am trying to add another static ip address to the list
the message above in title pop up, how can I fix it?
DHCP Table is Full!
View 1 Replies
View Related
Feb 25, 2013
Region : Australia
Model : TD-W8960N
Hardware Version : V4
Firmware Version : TD-W8960N_V4_130205_Beta
ISP : TPG
I have an Optus Home Zone (mobile cell tower) that requires ports open.
Port
123 UDP
500 UDP
4500 UDP
I have assigned the Home Zone a Static IP outside the DHCP range and set the above Ports on the NAT, Virtual servers to that IP address.
I have used nmap to scan the ports and it provides open/filtered status for all of them.
Here is the kicker for me, i use a DGN3500 netgear (which keeps dropping WiFi hence its replacement) and enter the ports and it works straight away. Un plug and put the Tp-Link and nothing.
I use Eset Smart Security, could that be the problem?
View 1 Replies
View Related
Feb 27, 2013
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : wind infostrada
TD-W8970 Wireless connection problems|
Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Wind Infostrada
That's a wonderful router on the paper! Really it has some problems with the wireless connection and the dhcp server. After 2 days of i must forced to reset the router because it refuse any wireless connection while the internet browsing on the other pc connected via ethernet ARJ45 is very slow.To complete the scenario the router doesn't allow any acces to his console page ..so what's the problem?
I try to change any channel for the wireless without no positive result.I bought it on amazon but if this situation will continue without any solution from tp-link i will forced to send it back with a totally negative feedback on the product.
View 5 Replies
View Related
Mar 23, 2013
Region : Australia
Model : TL-WR941ND
Hardware Version : WR841N v8
Firmware Version : 3.13.27 Build 121101 Rel.38183n
Model : TD-W8968
Hardware Version: TD-W8968 v1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
I have two routers, a TP-Link TD-W8968 (main & connected to ADSL) and a TL-WR841N (client) and I'm trying to get WDS working over them in order to use my PS3/media player etc at the tv.
1) are these 2 pieces of hardware compatible for WDS? Status of both hardware seems to indicate yes
2) if compatible, what am I missing so devices behind the client router can access the internet connection.
View 10 Replies
View Related
Mar 10, 2013
Region : Italy
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120720 Rel.09287
ISP : alice
A couple of weeks ago I have bought a TD-W8961ND in replacement of my old modem/router (of another brand, to upgrade from Wireless G to N). I tried to replicate in the new router something similar to my old setup, so I programmed Virtual Servers (under the NAT menu) with the following rules: NATRules.jpg in an attempt to:
- grant access from "outside" Internet to my web server
- have a Wakeup-On-LAN from "outside" Internet ..etc.. without success. Please note that:
- I have successfully setup a DDNS server to reach my modem router from outside
- as for WOL, I defined my subnet mask as 255.255.255.128
- I have not set any other rule, nor in NAT, nor in routing or other
- I tried also with firewall disabled
- I do my testing by means of a smartphone with wireless disabled and Internet connection via mobile service provider
- Both the above mentioned functions were working with my old modem/router (and still work on LAN), and I have not changed other things (PC setup etc)
View 14 Replies
View Related
May 25, 2013
I recently modified my home network in hopes of getting faster file transfers between devices. But it looks like something's not right.I'm suing Lan Speed Test and the best performance I get over WiFi is about 44Mbps (avg.). From my laptop to my NAS. If i turn off the WiFi and do the test over a wired connection the best I get is 200Mbps (avg.).
1. AT&T 2Wire cable modem. Internet comes in the house through this box and it's currently set up to be in bridge mode so that the TPLink router handles everything.
2. TP-Link WDR3600 gigabit/wireless router set to work in 5Ghz only, 11an mixed mode.
3. WD My Book Network Storage. Wired gigabit connection.
4. Desktop PC. Wired gigabit connection.
5. Laptop PC. Wireless.
6. 1 ipad v.2, 2 iphone v.5. Wireless.
Current setup:
1. internet cable goes into 2Wire Modem.Wireless on this device is OFF.
2. cable goes from LAN port on modem to WDR3600 router's internet port
3. cables go out from router to Desktop PC and NAS
4. all other devices are connected to the 5GHz wireless network created by the router.
View 1 Replies
View Related
Nov 8, 2012
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Trying to use TL-WR702N in bridge mode at a hotel. For some reason, every time I set the DHCP parameters to enable DHCP, then save and reboot, upon reboot DHCP is disabled. Of course, without DHCP then bridge mode is useless because I cannot then share the hotel wifi connection with multiple devices.Am I missing something obvious, or is there a trick to getting DHCP to be accepted?
View 11 Replies
View Related
Dec 3, 2012
Region : France
Model : TD-W8968
Hardware Version : V1
Firmware Version : TD-W8968_V1_120926
ISP : SFR
Device in question: siemans C610 IP voip phone
Configuration:
* The C610 is directly connected to TD W8968 via the ethernet port number 3 >> ethernet port number 1 is connected to the devolo homeplug 200AVPLUS . The PC is at the other end of the homeplug network
* The DHCP address starts at 192.168.1.100 - 192.168.1.199.
Symptom:
1. It takes a long time (about 2-3 minutes) for the C610IP to obtain the IP address of 192.168.1.100 after the synchronisation of the ADSL line is finished 2. In the DHCP client list, I could only see the IP address of the PC (192.168.1.101) but not the C610 IP. However, if I type 192.168.1.100, I could access to the configuration page of the C610 IP. - I only managed to see the C610IP once in the DHCP client list.
I tried to unplug -> replug the router but to no avail.
View 2 Replies
View Related
Feb 11, 2013
-Region : UnitedKingdom
-Model : TL-WR841N
-Hardware Version : V8
-Firmware Version : 3.13.18 Build 120522 Rel.31564n
-ISP : Virgin
I bought a TL-WR841N to use instead of our Virgin Super-hub which dropped the wifi regularly. It took me a while but I stumbled with the set up and got it working.Super-hub (in modem mode) - cable - TL-WR841N - 2 x cables running to 2 switches for (TV, Sky+, WII) and (PC, X-Box). Everything is spot on apart from the other half's Iphone and Ipad. Neither of them can get on the web in the bedroom. Both apples will join the network, but none will be able to get onto the web. The Wifi bars are on display on both products but they just keep spinning and searching to get on the web. I bought a Huawei repeater plug hoping that would work, but it just slows down everything else that can get on the network.Remembering that this happens only in one room, is there something that I can alter that would let these 2 apples access the web besides walking out on the landing every time she needs to update a web page ?
View 5 Replies
View Related
Mar 7, 2013
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : MTNL
After lot of troubleshooting and efforts I figured out there seems to be BUG with routers firmware 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n.When you enable Bandwidth control, FTP stops working from Internet. However, it does work from local network. When you disable Bandwidth control, FTP starts working from internet as well as local network.
View 1 Replies
View Related
Apr 8, 2013
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : TD-W8951ND_v5_120522
ISP : N/A
The wireless adapter settings page has an entry for 'PIN' and 'PBC' for WPS.Selecting either always results in the client station requesting the routers pin, indicating that the pushbutton selection is not working properly.The router was doing this with the version of hardware that it was shipped with. i have downgraded to 120522 and the router is behaving exactly the same.Has anyone successfully configured the router for pushbutton connection? do not suggest that we use the pin setting as we have a requirement for dumb devices to connect to wireless and they only support pushbutton connection.
View 1 Replies
View Related
Jan 28, 2013
Region : Philippines
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
I have a PROLiNK H5001N ADSL Wireless Modem using bridge mode to my TL-WDR4300. I login to my ISP using the TL-WDR4300 with secondary connection to my modem so that I can open the modem setup page.
1.) My question is can the Prolink get DHCP address from the Wan Port of TL-WDR4300?
2.) Can I still use the Wifi of the modem to get internet?
3.) If I connect my ISP to Prolink then connect TL-WDR4300 thru static connection, will the NAT and Hardware NAT still work in the TL-WDR4300?
NOTE: the latest firmware built TL-WDR4300_V1_121225 seams to have internet connection lost problem after a few minutes. I reverted back to 3.12.23 and the problem is gone.
View 3 Replies
View Related
Dec 9, 2012
Region : Poland
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : [url]...
I'm having issues with DHCP server not dealing IP after few hours (varies between 1h and 8h) of torrent traffic. If no continuous torrent traffic is applied, the problem does not occur. New wireless devices connect to the wi-fi network, but get stuck on 'getting IP adress'. The problem is with DHCP service or the wireless network service. New wired devices receive IP. The problem is only with wireless devices. I have no additional wireless device, that I can configure the network settings on my own (only phones) to check if it works without DHCP server giving IP. Wired connection is stable, but the bandwidth usage curve becomes somewhat similar to a sinewave.
I did disable the hardware NAT because that feature made the router unstable and caused it to hang up within minutes.
View 7 Replies
View Related
