Cisco / Linksys SE2800 - Getting Intermittent Unidentified Local Network?
Dec 11, 2012
I have cable modem coming into the basement hooking up to Linksys Cable Modem (1 yr old). The cat6 line leaves the cable modem and goes approximately 60' through the wall to an Asus-NT66U wireless router on the main floor into the WAN port.I then have a cat6 line go back through that same 60' of wall coming off the LanPort1 of the Asus-NT66U router into a Cisco/Linksys SE2800 8 port gigabit switch (a year old as well).
The problem I am having is as follows. I have been getting intermittent "Unidentified Local Network" problems off an on which I have tried many of the fixes for, evidently unsuccessfully ranging from duplex speed, network ID etc. I had updated the firmware on the NT66U to the latest and am still having problems.
I never have problems with the wireless network which always has connectivity to the internet, however the local is the regular problem. So, to further compound things I have 3 Smart TV's hooked up to the Cisco SE2800 switch over cat6 as well. Those were all working recently until this most recent hiccup and now none of them are working regularly. They can sometimes "see" the wired network and my media server software, but it is intermittent, slow, and never works and often can't see at all.
The TV's are all set to static IP's over the wired network (192.168.1.114/.115/.116) they are the only static IP's out there.The cables are all good and have been repeatedly tested in a variety of ways. All the drivers and firmware are up to date.I think I have a problem with the router/switch communicating and passing through data,The switch does not need a crossover cable, does not seem to have a management menu, and not sure what else to do.
View 2 Replies
ADVERTISEMENT
Jun 21, 2012
My wireless adaptor is preventing me from connecting to the internet at home, it enables to me o find the router and type in a password but only shows " unidentified network and local connectivity" with no access to the internet. When connecting via LAN, i am able to surf the internet. i have tried a full system restore, update drivers , enable and disable drivers but still nothing
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft� Windows Vista� Home Premium, Service Pack 1, 32 bit
Processor: Intel(R) Celeron(R) CPU 900 @ 2.20GHz, x64 Family 6 Model 23 Stepping 10
Processor Count: 1
RAM: 3032 Mb
Graphics Card: Mobile Intel(R) 4 Series Express Chipset Family, 1292 Mb
Hard Drives: C: Total - 227472 MB, Free - 200337 MB; S: Total - 1499 MB, Free - 1440 MB;
Motherboard: Advent, Roma
Antivirus: None
View 10 Replies
View Related
Oct 29, 2012
I have going up the walls the last week.Basically just moved house and got broadband installed, my girlfriends laptop connected automatically, whereas my Compaq CQ60 Presario Notebook WindowsVista will not connectI have checked so many different forums trying to fix this problem, but to no avail im afraid... it looks like there is an excellent internet connection.... but cannot go on the internet because it says "Unidentified Network local access only"
View 6 Replies
View Related
Jul 9, 2012
I had a tech from Comcast come out but couldn't figure it out. The tech said it could be my router but tried a different one and still nothing. The network, for me, is listed as "Unidentified" and the connection switches between Local Only and Limited Connectivity. It also says I am connected to my network with excellent strength. If I plug the router directly into the laptop it still doesnt work.
View 10 Replies
View Related
Nov 14, 2012
just a couple of days ago i started having problems with my internet, I can't seem to connect via an Ethernet cable?
View 1 Replies
View Related
Dec 16, 2012
I have a router connected ea2700 on the Internet port to a switch se2800.e switch is connected and everything is gigabit nas. if I try to transfer a file from PC, gigabit ethernet, the transfer rate does not exceed 8 MB/s. if I transfer a file from the NAS to the PC speed is 15 MB/s. the support advised me to change MTU manufacturer parameters,to disable protection,and clone the mac address.the situation has not changed.if I configure the router in bridge mode, the speed is 22MB/s and 45MB/s.
View 3 Replies
View Related
Oct 25, 2012
I have just installed a new router, a HUAWEI HG533 I am not able to connect wirelessly with my Acer Aspire 5520 (with Vista home premium).I can connect my new router using the ethernet cable, and last time I tried my old router would connect wirelessly.If I hover over the network icon, it says 'Unidentified Acess:local only'My smartphone (and my wifes) will connect (but oly mine to the old router!).I have tried removing the microsoft 6to4 adapters (suggested on another forum) this didn't work. (I then re-installed, no better).I've had a look at other posts on this forum, and Have done a couple of the tests suggested (wireless and mini toolbox, which I will post separately as it exceeds 20000 characters!)I have tried support from my ISP (who also supplied the router) and got a generic email in response, no luck.
View 14 Replies
View Related
Oct 8, 2012
i can search for networks. As you can tell i am currently on the internet on my laptop. I can search for the current network i am on through my adapter. I then connect to it. It says im connected to a unidentified network. It will not let me search the internet or anything else.
View 9 Replies
View Related
Jan 12, 2012
We run windows server foundation 2008 and have about 15 workstations. I had been running the network on 10 workstations prior to moving the server to our new location about a month ago. All was working well. We had run with the 15 workstations no problem in our new facility for several weeks. many of the computers are dropping the network connection now intermittently, with no predictable pattern. I can't seem to reproduce the conditions that cause the drops.
View 1 Replies
View Related
Jan 12, 2011
Running 5 PC's and a laptop on a wired/wireless network at home. One PC running Win XP Pro started dropping the network connection (so it appeared) during browsing. Have found the following:
1. MSN messenger runs fine, and doesn't drop out
2. AVG antivirus updates with no issues
3. Web Pages in Chrome and IE will load fine one minute, then cannot load or pause for 1-2 minutes while loading
4. Can ping web addresses/IP addresses from command prompt with no issue.
5. Have changed the network connection from Ethernet to Wireless, which makes no difference to the issue.
6. If I "repair" the connection, and the network refreshes the IP address, I can browse successfully, for about a minute, before the issue occurs again. "Repair connection" again and can browse again for a minute.
7. Checking connected devices to the Netgear router, shows the PC name sometimes, against the IP address, other times it shows the PC as "unknown" against the PC address (when this occurs, web browsing is lost)
8. All other PC's on the network are fine.
View 6 Replies
View Related
May 23, 2012
During this time we've had two different Internet Service Providers as well as two different modems. Also we've had 9 different devices connected to modem wirelessly. ( 2 Desktops, 3 laptops, 2 Xbox 360s, and 2 Nintendo Dss ) And this desktop is the only one that has had any issues, it's also the oldest of the devices. So I doubt the issue lies within networking but more with the actual desktop. I've even conneceted the desktop straight to the modem with an ethernet cord, also to no avail.
View 1 Replies
View Related
Apr 25, 2011
ok i did the cmd ipconfig and it says media state disconnected.also i uninstall a network adapter it was the isatap one also it had a yellow mark one it so thats why i tryed to uninstall it i thought it would let me install it agian but it didnt so i did that add legacy hardware so now it shows it in the hidden devices tad with out that yellow mark also when i try the problem and solution found the isatap sayinf could not load driver software click on it and it says windows was able to successfully install device driver software but the driver software encountered a problem when it tried to run.the problem code is 31. the control panel tad would all was say microsoft windows came up saying window explorer has stopped working windows is checking for solution to the problem windows explorer the internet was working then and it still was i think it had that internet ball on it but when i try to use the internet it wouldnt connect
View 8 Replies
View Related
Oct 31, 2012
E4500 local network IP is 10.10.XXX.XXX and the DHCP server also starts with this subnet. My network is 192.168.XXX.XXX based but if I manually chahge the routers IP I can no longer access it. I do not use DHCP as this is in bridge mode. Why is this setup this way...CCC?
View 1 Replies
View Related
May 6, 2012
am in the process of setting up an online business and now all of a sudden I have no internet access which is not good! I am connected to the router but it says unidentified network, local only...When I lost connectivity I spoke to my ISP provider and they took me through all the steps then determined that it is the router that is at fault and are sending me a new one. HOWEVER after I hung up I remembered I have an old router so I tried that one, same thing, then my neighbours gave me access to their wi-fi, same thing.... so suspecting that it is not the router I have dug out an old laptop which now connects fine to my router wirelessly.
View 19 Replies
View Related
Dec 12, 2011
I switched on my laptop today and it wouldn't connect to the internet because of an 'unidentified network' problem. Last night before I went to bed it was surfing the net fine and then this morning, nothing. No one has touched the laptop overnight and it was switched off all night so I have no idea how this has happened. I'm using my internet connection via my iPhone with no problems. I've already tried several things to try and fix the problem - I've reinstalled all network adapters, have fiddled with IPv4 settings, have deleted and re-setup my network connection, and have restored Windows to a previous point. I can't connect my laptop to the router using a cable because I live in a bock of flats where lots of people share the same router and it's locked in a security box, so I'm just using a wireless connection.
View 1 Replies
View Related
Nov 5, 2012
Right now I've been staying at a hotel and my internet doesn't work while my brothers laptop connects flawlessly. The only way the internet works again is by me tapping the power button and putting it to sleep and turning it back on then the internet works but only for a couple of minutes.
I've tried everything, I've installed the latest wireless driver worked a little then went back to the same problem then I rolled back the driver it worked then it went back to the same problem. I've tried everything I checked power options, I reset the winsock and Ip,I tried a vpn still no luck. If I go to network and sharing center and trouble shoot it say that the adapter is not plugged in or the DHCP is not enabled which it is. Like today I could barely get on because it just showed unidentified network with no hope of connecting. On Xirrus it shows the hotel has more one ssid with the same name.
View 5 Replies
View Related
Feb 27, 2012
recently i bought a phone that has the ability to connect your pc to the internet. It has worked great, but when i connect my ps3 or another computer to my laptop which i use the phone with, they all come up as unidentified network. I tried changing the setting on my computer, but cant seem to figure out how to change it from unidentified to home, so i can use the internet on connected pc's and my ps3.
View 1 Replies
View Related
Sep 15, 2012
I am in a network, where my laptop works in all other routers except my room's router, whereas other's laptop/PC supports my room's routerI'm out of the network.However, I'm now in same network, coin another router.
View 1 Replies
View Related
Jun 23, 2012
I have my wireless router that gives internet to all my computers (4), each one having their own usb wifi adaptor. This part works fine, never had any issue with internet.Each of the computers also have its own GBE adapter but i wasn't really using them. Until now, i bought a switch and connected all 4 computers through rj-45 to the switch just so i could transfer files easier and especially much faster than through the wireless.This is where my problem is, the network works, i can see and transfer files just fine, the issue being, on each and every computer, the lan is considered as unidentified public network. I've tried everything i could think of, yet, nothing, i can't change the status of the lan connection.
View 31 Replies
View Related
Aug 29, 2011
my gateway laptop, running vista 64 home premium, cannot connect to the internet at home. connects straight to the modem via ethernet. displays as 'unidentified network'. according to the Atlantic BB tech(my ISP), my laptop is not obiaining an IP addy from the modem. The modem seems good, and the tech could see the modem from his end, but no IP addy from the laptop. ran ipconfig /all from home and the gateway was 207.255.36.1(preferred) instead of 192.168.x.x So i'm stumped with no net at home. the ipv4 properties do have the obtain automatically button checked, and dhcp is enabled. had the tech reset the provisioning on the modem & he said the mac addresses were cleared already. i reset the ipv4, ipv6, and winsock. haven't gotten anywhere. tech's last advice was to bring the modem back and swap it for another one.
View 1 Replies
View Related
Nov 23, 2012
Namely an Unidentified Network with no NETWORK access. Some information first, the NIC that Im using is the Realtek PCIe Family Controller, Ive updated the drivers, Ive uninstalled, Ive reinstalled. Ive basically been on the internet for the past two days trying all the solutions. Including refreshing and renewing my ip, trying a static ip (although, Im still not sure if I did this step correctly) Ive tried disabling IPV6, Ive tried adjusting my speedflux. The problem is also intermittent with seemingly no reason whatsoever, some days Ill go without internet for the entire day, then the next day Ill boot up my computer and Ill have internet again. It should be noted that when I enable WIRELESS on my laptop, Im able to connect to the network, but when I enable wired, I am not able to.
Here is the ipconfig /all for when Im connected wirelessly and have a connection.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Windowssystem32>ipconfig /all
[Code]....
It should be noted that I am using powerline adapters for my connection, but as I said, this problem only recently started cropping up. I went fine for almost a week with no problems, then all of a sudden it started happening. Im still able to connect wirelessly so its not too much of an issue, but I prefer via Ethernet..
View 2 Replies
View Related
Aug 6, 2011
My pc is windows 7ultimate and my laptop is vista ultimate. the router is connecting fine to the pc. as i try to connect to the laptop it keeps saying unidentified network and local access only. i tired different things but nothing seems to work. it will work only when there is no password on the wireless.
View 3 Replies
View Related
Nov 23, 2012
Recently I've been having some internet problems. Namely an Unidentified Network with no NETWORK access.the NIC that I'm using is the Realtek PCIe Family Controller, I've updated the drivers, I've uninstalled, I've reinstalled. I've basically been on the internet for the past two days trying all the solutions. Including refreshing and renewing my ip, trying a static ip (although, I'm still not sure if I did this step correctly) I've tried disabling IPV6, I've tried adjusting my speedflux, believe me I've tried just about everything, I don't have one blue link left when it comes to my google searches on fixing this problem.The problem is also intermittent with seemingly no reason whatsoever, some days Ill go without internet for the entire day, then the next day I'll boot up my computer and I'll have internet again. It should be noted that when I enable WIRELESS on my laptop, I'm able to connect to the network, but when I enable wired, I am not able to.[code] I'm still able to connect wirelessly so its not too much of an issue, but I prefer via Ethernet.
View 2 Replies
View Related
Oct 15, 2012
I have a Cisco 1242 AG wireless access point with the goal of having multiple SSIDs. I set up one network which broadcasts correctly but only sometimes can I connect to it.
And, even if I connect to the network, I cannot get a DHCP address for the client.Other devices connected (but not through this Access Point) to the associated VLAN 60 can get a DHCP address and connect just fine.Here is the configuration for the Cisco 1242 AG access point in question: [code]
Lastly, here is the information on VLAN 60 from the distribution switch. As mentioned, other devices connect to this VLAN and get IP addresses just fine.
View 11 Replies
View Related
Oct 15, 2012
I have a Compaq with XP wired on a Network with a Belkin N600 Router.There are 5 computers on the Network, (4 wired, one wireless) and this is the only computer that I have problems with connectivity. It connects to the Belkin through 2 switches.Typically when I turn the system on it connects, downloads mail, etc. After a short period of time there is no connectivity to the network for printing nor the internet.I may get connectivity randomly again after a while, but you never know if or when you will get connectivity again for sure. I am using Explorer.I had loaded some Belkin software with no luck so I uninstalled it. The other computers have no special software for the router.
View 1 Replies
View Related
May 1, 2012
I have a E2500 connected to a cable modem as the base of my home network. Hard wire connected to the E2500 is an linksys 8 port hub and a couple of computers. The 8 port hub is connected to a couple of computers and a xbox. I have the hub as a distro point to cut down on wiring. Wirelessly connected to the E2500 are a variety of laptops, netbooks, ipods, an ipad, a playbook, an iphone, a android phone, a wireless printer and a Ps3. Most of the devices are just using the wifi for internet access. Most devices have been setup with their own ip addresses to avoid ip conflicts. The computers and laptops/netbooks are running either Windows XP, Windows 7 or Mepis Linux. Up until now everything was going as good as can be expected, all the computers could see each other and most could transfer files between each other except when Windows gets picky.In the last few days no computers can see each other. Windows or Linux.Everything can accsess the internet and wirelessly print still just can't see each other. I reset the E2500. I updated the firmware on the E2500. I installed the Cisco Connect software (just in case I was too stupid too setup a router). Still nothing. I can ping other machines from a command prompt in windows or a terminal in Linux and get a good ping back. In the router setup via a browser I can go to the status page and see other devices on the local network but most are just ipods, ipad, playbook and the wireless printer, If I go to the administration page / diagnostics I can ping other computers and get a good answer. I just can see them from each other. I think I've rebooted every thing at least once. Yes the workgroup names are all the same (workgroup) and yes file sharing is turned on on all computers.
View 3 Replies
View Related
Aug 3, 2012
In the settings menu, there is no l2tp in which it was possible to configure a local address of the router. It should be: 10.155.41.41There is an option only for VPN server setup(10.255.255.254), but where it takes a local address that my provder has gave me? - it is not clear. At the same time in the status of the router receives a DNS correctly and the second address embarass me little bet DNS should be:
1) 80.252.130.253
2) 80 252.130.254
first dns is correct, and second one looks like: 80.252.45.86Maybe he does not take a local setting of ip adress via DHCP?
View 9 Replies
View Related
Jun 5, 2012
I've been playing around with my E4200 but cannot find the right combination of settings. My problem: I bought the router for cable internet that never happened. In the meantime I am accessing the web using a 3G dongle. Hoewever, while connected to the router (wired or wireless), all the PC's in my home refuses to access the 3G internet - it is as if it wants to use the E4200 to access the net, no matter what. So every time I want to access the internet, I have to disconnect the PC from the home network, and connect with the 3G on that particulat PC. (I have three PC's at home, 1 wired and two wireless). If I set the E4200 to bridge mode, I struggle to find a logical IP address, since I would ideally like to run the network at 192.168.1.X. How do I set the E4200 to allow a home network to be established without having to disconnect everytime I use the 3G on a PC? Also, it seems that if the router doesn't handle the DHCP duties, win7 by default makes the network public, which complicates sharing a lot...
View 5 Replies
View Related
Sep 19, 2012
I cannot connect local IP addresses that are connected to X3000 THROUGH LAN CABLE, but we can connect to the local IP addresses that are connected to X3000 THROUGH WIRELESS.There is definetly something wrong with the software of the X3000 since it is the only DHCP server on my network.I have 3 routers connected to X3000 thru LAN cable, the strange thing is when i connect to one of those 3 routers i can connect all devices in the network whether wired or wireless.when i connect to X3000 thru wireless i cannot access to those LAN devices in the network unless they are directly connected to X3000 thru wireless.and when i connect to x3000 with a LAN cable everything works perfect, i am able to access all devices in my network.
View 7 Replies
View Related
May 15, 2012
basically was online with my desktop until around 4am central US time. Went into the other room and fell asleep. Woke up around 9am, sat back down, Unidentified network and No Internet access. That's where this god-awful day began. I've tried so many things (from tech forums) I may forget a few... I've tried disabling IPv6, disabling Bonjour, enabling/disabling the adapter card, all kinds of stuff in the command prompt... reset this, flush that, restart restart restart restart restart. I uninstalled the adapter driver, rebooted, installed the latest from a flash drive, didn't do anything. Really the only suggestion I haven't taken is recovering Win7 from factory specs and reinstalling about everything since one guy said that still didn't fix it and this is causing enough trouble already without more misery in the mix.
View 1 Replies
View Related
May 30, 2012
The wireless adapter keeps saying unidentified network, I can connect from other computers and they are all working fine.Forgot to mention its a ASUS wireless n-15 adapter, also the system is a Windows 7 64 bit.
View 1 Replies
View Related
Mar 10, 2012
My laptop is unable to connect to the internet. It recognizes my wireless connection (public network) as "unidentified network" and Access: "Local only." I've tried using many other solutions but I still haven't found a way to fix this. My other laptops, computers, and gaming devices are able to connect to my linksys router except for this laptop. [code]
View 10 Replies
View Related
Dec 16, 2012
So one day i turned my computer on and the internet said unidentified network, i been using the same modem with Verizon it worked fine. I have disabled the adapter, unistalled it all that and still does not work, i tried to make a new connection it still does not work, im in school and my computer is how i submit my work. I have called technical support with verizon they said its my computer.
Ipv4 address 169.254.195.91
Subnet mask 255.255.0.0
View 14 Replies
View Related
