Iused my installation cd to re-setup my linksys. I moved and used a laptop previously. Now i am at a house that has a desktop. I want to keep the desktop wired and make my laptop wired. So, when i went to re-install it said i had to reset my linksys to factory settings.
View 2 RepliesHow to reset my router to factory settings so i can install it on a new computer
View 2 Replies View RelatedI was having some connectivity issues with my network of WAP54G's, so I had a technician come to have them looked at. The technician turned out to be completely clueless, and he messed up one of the APs in the process. He changed its IP address and apparently updated its firmware, but he didn't write the new address down, so now I can't access its administrator panel. I've tried to retrieve the IP address using the setup CD that came with the AP, but it doesn't even see the AP in my network. I've tried to factory reset the AP by holding the reset button for 10, 30 and 60 seconds and unplugging the power cord, but to no avail. It still doesn't bring up the admin panel when I enter the default IP in the browser. I think I've tried everything I could find on the Internet about this problem that didn't involve cracking the AP open, but none of it has worked.
View 4 Replies View RelatedMy computer is an XPS 360 with alot of upgrades. After looking at the specs of D-links routers I thought I give it a try. Hooked up, works like a dream. Couple months later my computer was saying I have "limited connectivity." All of the other computers have full access and works great. I tried going to my routers home page, but all I get is "The server at 192.168.0.1 is taking too long to respond." Ive tried renewing the ipconfig, restarting everything, new cables....everything I can imagine. I tried calling my ISP and they told me it wasnt there fault, that its pretty much on my end. I called Dell for support, said my warranty went out and they cant do a thing.
View 14 Replies View RelatedI have windows vista, and forgot my network password. I reset my router to factory settings by pushing the reset button on the back.I tried reconfiguring the router from the network icon, but at the end of the process it says it cannot configure my router.I lost my internet service in the process
View 1 Replies View RelatedI am locked out of my Arris wtm652 (unable to login with default password or the password that i set). I have tried every way I know of to reset the modem outer to its factory settings but to no avail. I know that it is not being reset because I still can not login to it and it is maintaining the wireless security settings that were set for it.
View 1 Replies View RelatedI have completed my CCNA qualification and i am doing some volunteering for a none proffit eletronics recyciling company they receved some cisco pix 515e firewalls and i was aloud to keep one so i can learn how hardwaire firewalls work and how to set them up but i can not seem to connect to it is there a way to completely reset the device to factory settings without any ip address or passwords i do not have any cables for the device but i have made a straight and cross over cable and there is a box of cables at the recyciling company from diffrent places if i need a specialist cable i may be able to find one
View 6 Replies View RelatedRecently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies View Relatedi have a wrt54gl version1.1 ok so let me start from the beginning.a few months ago i left the contry so a friend of mine asked me to lent him my router. a few day`s ago i got back and got my router back. it was working fine until i got it back. the rest button won`t work. i can`t reset the router to factory default. the user name was blank and the password was admin.now it won`t let my to do that.
View 9 Replies View RelatedDue to password loss, I get to reset the E4200 to factory default in order for router re-config.After pressing the reset buttom for 10sec, the router reset. After then, I could not access the router via browser with 192.168.1.1 at URL entry. My PC IPv4 setup: 192.168.1.11; subnet=255.255.255.0.But, ping 192.168.1.1 from PC was OK without packet loss. So router was restored with 192.168.1.1 and cable connection was OK.
View 2 Replies View RelatedWe've lost our WRT120N's administrator password and are trying to reset it to factory defaults.One peculiar thing that we have noticed is that the router has an IP of 192.168.106.1 rather than the default of 192.168.1.1 (this is verified by the default gateway, as well as a login prompt when 192.168.106.1 is put into a browser).Things we've tried to do to reset the router:
1) Press and hold the reset button at the back of the router for 30 seconds
2) Press and hold the reset button at the back of the router for 60 seconds
Interestingly, doing either of these things seemed to have no effect on the status lights.
I can't seem to login to my admin. the IP for me is 192.168.0.1 and I can't login. I tried resetting the router a few times and no luck.Is there ANY other way to reset the username and password?
View 6 Replies View Relatedhow to reset password on a WRT54G2?
View 3 Replies View RelatedMy router wasn't giving out proper ip addresses so I went through the steps to reset the router to factory defaults. After I tried to run the setup off of the cd which came with the router and the program is saying it can't find my router
View 9 Replies View RelatedWRT54G2. I forgot password , but have to reset anyway. Currently have desktop w/XP. a laptop w/Vista and will be adding a Widows 8 64 bit laptop.. Any special consideration for settup with the Window 8?
View 1 Replies View RelatedI was trying to do a hard reset and power went off. Since then if i plug in electricity in my router all lights lit once, then all turn off.
View 4 Replies View RelatedI have installed the HP drivers for my HP LaserJet 1102w printer on my Windows 7 (64 bit) Professeional and Windows XP laptops.They both print fine over the network using the WRT54G2-V1 router immediately after installing the drivers. However after shutting down either the computers or printer the settings are lost and the printer willl not work unless the drivers are reloaded.
View 9 Replies View RelatedI lost DSL, requiring a reset from Cincinnati Bell. After that, the router behaved strangely, wouldn't connect, etc., so I upgraded to the latest firmware, did a bunch of hold-the-reset-button-for-30-seconds resets, etc., and it seems to be working again.BUT.... the download speeds are very slow, both over wireless and through a wired connection to one of the router's ports. I'm gettting anywhere from 60kbps to 400kbps, but it's been hovering around the 100-200kbps range. Upload speeds are fine, nearly matching those over a direct DSL modem connection.
View 4 Replies View RelatedOk, so I reset the router but i still can't login to the setup using the factory password (admin/admin) (blank/admin) (admin/blank). Now I have an unencrypted network and no access to the setup... I even tried using the setup CD but it doesn't recognize the router.
View 2 Replies View RelatedMy EA6500 has been working fine for the last few months but a few days ago i upgraded to the latest firmware 1.1.28.147876 - this was done by an ethernet cable, not by wifi. However i've noticed the router reverts back to the previous fw 1.1.28.146856 when the router is rebooted or factory reset. I've repeated the fw upgrade process and also done a hard reset before upgrading the firmware but no avail. Normally after firmware is 'upgraded' the router reboots and i get the message "firmware successfully installed" but then on subsequent reboots the firmware reverts back. I'm using local router access but even using smartwifi gives the same issue. When upgrading fw, i've tried both options online & manual but again makes no difference.
Don't really fancy calling Linksys support and going through 4 hrs of basic trouble shooting. Or perhaps Cisco have introduced a new automatic firmware downgrade option in their routers?
I flashed the firmware and the ipv6 automatic is on disabled and I cannot set it to enabled.the 6rd tunnel option I can change but that has not effect- in fact from what I looked up it seems to be something used by some cable providers.hate to have to reset the router to factory defaults and then reset the network up - just to see if i can get the option to set IPV6 auto to enabled.
View 3 Replies View RelatedI have an e4200 with the latest firmware 2.1.39. I just upgraded the firmware due to connection issues with my DSL. I now have the same issues with disconnects but I believe they are being caused by a different issue. When I try and log into my router through the IP address it wont let me, it says it can't find the router. Eventually after getting in the first time by using the default password, I have twice found out that all my settings are gone. This has happened twice this week and only happened after upgrading the firmware but I can not tell if firmware is causing it or if it is hardware related. I now reboot and restore saved firmware but that is a hassle and am pretty sure that is not the way it was designed to work.
View 9 Replies View RelatedI've just managed to reset the WRT 300N to default settings and have setup the internet connection etc and home network ... BUT no matter how I've fiddled with the wireless settings I cannot get any of the laptops or mobile phones to connect wireless to the network.The Windows software on the laptops 'finds' the router OK but for some reason the router seems unwilling to supply an IP address.I've checked ALL of the settings that I can think of, and all are correct ... well, all are exactly the same as my old router which worked perfectly.
View 4 Replies View RelatedI have been using Linksys WAG200g as a modem&router at my home for few years already and it did a great job. Plugged it on 24hours non-stop. Default firmware.
However, in the past months WAG200g did the factory reset by itself. It happened once a month, 3 months in a row already. No body pressed the reset button nor use the web admin to reset it. It reset itself. All the SSID, IP Address, passwords, etc are reset to default.
If I use the reset on the back of the WCG200 and reset it to the original factory settings, does the firmware version revert to the original version?
View 2 Replies View RelatedI reset unplug did everything according from cisco.com it didn't work.Can not go to 192.168.1.245. What next I need to do to make it work.
View 3 Replies View RelatedGot a Belkin wireless modem router some 18 monthes ago, and after a bit of a struggle managed to set it up. It worked fine, aside from the odd depower repower. For some reason, it just stopped working yesterday. I initially checked all my cabling etc and everything seems fine. I next tried resetting my modem/router to factory settings. When I tried to install the Belkin software I fell at the first hurdle with a message saying "The setup assistant is not able to connect to the router". After googling my issue, I followed others advice and running the cmd setting and typing in "ipconfig" only to find that my media state was disconnected.
View 2 Replies View RelatedWe've recently changed data line providers and now have some Cisco 877 routers we'd like to reconfigure and use at other sites. Although we own these, they were configured by our old data line providers, I'm having a hard time of resetting them to factory defaults. The simple, hold down the reset button until it restarts does not work.If I press the reset button within 5 seconds of power up to load the default rom image, I get the below:
System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Technical Support: [URL]
Copyright (c) 2006 by cisco Systems, Inc.
C870 series (Board ID: 1-148) platform with 131072 Kbytes of main memory
Booting flash:c870-advipservicesk9-mz.124-24.T.bin
Error opening: flash:c870-advipservicesk9-mz.124-24.T.bin
[code]....
I assume from this the required bin has either been removed, renamed or overwritten.As soon as the router boots it requires a password and I dont have the password to be able ftp files in and out of it.
I have installed DD-WRT firmware onto my new D-Link DIR-615. It causes some problems and I'd like to re-flash router with orginal firmware. After turning router on with Emergency Room mode and choosing right (as for me) image file I'm getting "Unable to upload the image, please make sure the uploaded file is the correct image." Information.
Firmware downloaded from: [URL]
How can I fix my router? Which firmware file will be correct if not an original?
I have a (Air Access) - ZG-5000-11g Wireless Outdoor Bridge , Ap Router, It has hanging problem, so I make it factory default. but now I have unable to configure it. find out default ip address.
View 5 Replies View Relatedi don't have the cd to set my wireless router back up, so how do I go back to factory setup without it?
View 2 Replies View RelatedI am the owner of an Asus N53SV series laptop running windows 7 home premium. I factory reset my PC in order to have a "fresh" new year, but now I can only connect to the wireless internet in my house using the ethernet cable. When the cable is unplugged, no networks show up for my laptop. I tried going to this link: ASUSTeK Computer Inc. -Support- Drivers and Download N53SV I downloaded the first wireless driver listed...and it gave me an error that just said "error azureware wireless lan driver"....not a very informative error.
View 13 Replies View RelatedThe ap 3502i has been registered to the wireless controller, but now want to restore the factory settings, repeated after the upgrade or will appear before the registration information of the wireless controller,
View 3 Replies View Related