Belkin Routers :: 300n Cannot Log Into 192.168.2.1 / Cannot Factory Reset / Seem To Be Stuck
Mar 14, 2013
I upgraded my internet connection through charter and they shipped a new modem. Installed my new modem and my 300n will not connect to it. So in my attempts to figured things out I went it in and set it up as an access point only. I can access the internet on my desktop but there is no wireless signal in the house. Cannot connect to 192.168.2.1 now either. Tried the manual reset to factory defaults with no luck. At this point all I get is the small flashing blue light and the tall skinny light is not on at all.
View 5 Replies
ADVERTISEMENT
Dec 29, 2012
What buttons, in specific order, do i press to reset my router? i used to know how but can no longer find that info
View 2 Replies
View Related
Dec 15, 2012
The facility provides WiFi access. I'd like to configure his router to access the facility's WiFi, as WAN access to the internet while providing DHCP service to the wired ports. The idea is to use the 4 wired ports to provide inter-connectivity to each other and internet access via the router's wireless connection via wireless for internet access by the wired client machines.I'd also like to firewall the wired devices from access by other users of the facility Wireless network.Can I do that? How do I configure the wireless aspect of their Belkin Share 300N? What other settings do I have to set.
View 2 Replies
View Related
Feb 5, 2011
I am trying to set up this new extender on XP platform. I have only got as far as the username and login screen. I assume that this is asking for the nambe by which the PC (with me as user) is known and the password for this PC. I cannot get these recognised.
View 4 Replies
View Related
Oct 30, 2011
I have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
View 1 Replies
View Related
Feb 15, 2009
Recently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies
View Related
Dec 8, 2012
I have a belkni F5D Router and I have lost the password to access it. I dont have any computers or devices that still connect to it, and I really need to know how to hard reset the password!
View 2 Replies
View Related
Dec 28, 2012
disconnected for 30 seconds and reattached power-still no lights or service. Reset button still no lights or service?
View 1 Replies
View Related
Feb 6, 2013
How can I reset my N wireless router f5d8233-4v3? The reset button must have been pushed inside. I was setting it up as a repeater and then it keeps timing out.
View 1 Replies
View Related
Mar 6, 2013
I'm trying to re setup my mother in laws Belkin F9K1002 wireless router. She has no clue as to what her password is for the wireless network or any other Belkin password. When I go to the support website, there are instructions to reset the network password, but you have to login to change the settings. The instructions say to leave the password field at the login blank but when I leave the field blank, I get an error message "Incorrect password. Please confirm your password and try again." So it seems I need the password to reset the password.
View 1 Replies
View Related
Dec 26, 2012
i need step by step instruction to disconnect and reset my Belkin 450 DB router
View 1 Replies
View Related
Jun 13, 2013
According to the Belkin support tech, apparently the weather (?) may have effected my Belkin Model F5D8235-4 v3 router. My wife pressed the re-set button instead of powering down which according to the tech set my router to reading zero (0).Belkin tech refused to tell me how to re-set the router unless I paid $75 for a six month support plan because mine expired recently.
View 1 Replies
View Related
Dec 24, 2012
I've just hooked up my previously used N300 router. The router is showing a solid green light, and the laptop recognizes that a solid Belkin wireless connection is out there. I cannot for the life of me remember the network key and/ or pass phrase I originally set. No, I did not tape this info to the underside of the router as suggested in Belkin instructions.
View 6 Replies
View Related
Dec 24, 2012
I need to reset the channel on my N300 router but in order to do so, I need to log in. The log in screen does not take my existing password. How do I get my current password or reset my password? It should be the simplest thing, but I have found this to be extremely difficult with Belkin.
View 1 Replies
View Related
Feb 1, 2013
i forgot my admin password and i want to know if there is a way to retrieve or reset it. I have the enhanced wireless router model F6D4230-4 V1
View 3 Replies
View Related
Jan 4, 2013
Is there a way to avoid network interruptions when resetting the F5D8235-4 v3 router? I was hoping to find a config file or some other way to avoid having to reset the home network and devices. The administrator password has been lost, so i would like to reset that only and not restore factory settings.
View 1 Replies
View Related
Apr 22, 2013
Why My Belkin Router F5D8236-4 Ver 2 always rebooting itself. the router lamp is on and then the security lamp is on and then the router rebooting itself. this happening because im push the reset button. im already try to upgrade the firmware with recovering tool (Boot Loader / Tiny Kernel Version v0.02) from 192.168.2.1 but the problem still happening.
View 3 Replies
View Related
Feb 18, 2013
i forgot my password for my belkin n150 wireless router so now it wont let me change any of my settings.i called tech support and all they wanted to do is get into my computer and sell me security progams .when i told them no they wouldnt reset my password and hung up.
View 2 Replies
View Related
Apr 25, 2013
What do I do if my routers light stays amber and wont turn blue? The wifi is not working because of this even though it is saying the signal strength is excellent and I have already done the reset a bunch of times its been two days and I just cant get it to work. Its the N300 router
View 2 Replies
View Related
Nov 25, 2012
I'm am getting a "Could not find DHCP daemon" error in the router log (N300 router), but when I connect my cable modem directly to my computer it gets an IP address just fine so I doubt the problem is with my modem or ISP. I've tried resetting the modem and router multiple times but no luck.
View 2 Replies
View Related
Feb 25, 2013
I forgot the user for management a IPS SSM-10, when i follow the procedure to reset the password for cisco user, i can get into the module, i change the password and every thing is OK, but when i tried to configure y don´t have rights to do anything.
if i see the privileges for the user cisco this is the result. [code]
View 4 Replies
View Related
Aug 18, 2011
I've inherited a IAD2430 router but I don't have the ena passwords nor am I able to do a break and do a password recovery. I'm familiar with the password recovery process and config reg settings but this one has me stumped.
The config register is set to 0x2102 so I see nothing at all when it boots until it's completed and I get the prompt to "Press RETURN to get started!" I get to non priv mode but without the password obviously I'm going nowhere at that point. All the docs I've come across so far assume you can break out of the boot process or are already in rommon. When I remove the flash: I get no output at all... The IAD has no "reset" button like the CAT switches either..
I don't need the current config, just a reset/format of the NVRAM.
View 2 Replies
View Related
May 5, 2011
I am locked out of my Arris wtm652 (unable to login with default password or the password that i set). I have tried every way I know of to reset the modem outer to its factory settings but to no avail. I know that it is not being reset because I still can not login to it and it is maintaining the wireless security settings that were set for it.
View 1 Replies
View Related
Dec 29, 2012
I am the owner of an Asus N53SV series laptop running windows 7 home premium. I factory reset my PC in order to have a "fresh" new year, but now I can only connect to the wireless internet in my house using the ethernet cable. When the cable is unplugged, no networks show up for my laptop. I tried going to this link: ASUSTeK Computer Inc. -Support- Drivers and Download N53SV I downloaded the first wireless driver listed...and it gave me an error that just said "error azureware wireless lan driver"....not a very informative error.
View 13 Replies
View Related
Jan 2, 2013
I need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.
View 4 Replies
View Related
Aug 10, 2011
I have been using Linksys WAG200g as a modem&router at my home for few years already and it did a great job. Plugged it on 24hours non-stop. Default firmware.
However, in the past months WAG200g did the factory reset by itself. It happened once a month, 3 months in a row already. No body pressed the reset button nor use the web admin to reset it. It reset itself. All the SSID, IP Address, passwords, etc are reset to default.
View 1 Replies
View Related
Jan 18, 2012
I have a DIR-655 (HW rev A2) that has worked mostly fine for a long time. Today I decided to do a firmware upgrade, and in preparation I backed up my custom config settings and did a hard reset via the factory reset button on the back of the unit.
Since then, the unit itself has been inaccessible from my computer. If I connect the DIR-655 and a PC with a network cable, the appropriate light goes on on the front of the router, but the client does not lease an IP address from the router and I can't access the router home page at 192.168.0.1.
I have tried the reset button again and also power-cycled multiple times, and I have tried connecting from multiple computers, all with the same unsuccessful results. how to "un-brick" the device?
View 6 Replies
View Related
Apr 26, 2012
If I use the reset on the back of the WCG200 and reset it to the original factory settings, does the firmware version revert to the original version?
View 2 Replies
View Related
Jan 4, 2013
I had DAP-1522 setup for more than two years and working fine. I changed the default IP address from 192.168.0.50 to 10.0.0.50. Recently I replaced my older router with a new one, and now I want to reconfigure the DAP-1522 with the new router, but unable to login. I tried to factory reset but it doesn't seem to work. When I hold the reset button for 10-20 secs, I see the blue power light blinking, but it continues to blink forever. I left it for 4-5 hours and no difference yet. how to successfully reset to factory defaults so that I can access it using 192.168.0.50 IP address?
View 1 Replies
View Related
Sep 24, 2012
My team already bought one 1800 Series router. And they setted some passwor.
Right now i am not able to login. I know the cisco password recovery method to reset the password.
Instead of password recovery method i want to try with total factory default setting.
is there is any method to do factory default without login
View 5 Replies
View Related
Feb 27, 2013
I got a ASA5505 back from a Office. I don`t know the IP Address to connect to the ASA. How can i reset the System to the Factory Settings.
View 1 Replies
View Related
Jan 22, 2012
I have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default
View 1 Replies
View Related
Sep 3, 2012
We've recently changed data line providers and now have some Cisco 877 routers we'd like to reconfigure and use at other sites. Although we own these, they were configured by our old data line providers, I'm having a hard time of resetting them to factory defaults. The simple, hold down the reset button until it restarts does not work.If I press the reset button within 5 seconds of power up to load the default rom image, I get the below:
System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Technical Support: [URL]
Copyright (c) 2006 by cisco Systems, Inc.
C870 series (Board ID: 1-148) platform with 131072 Kbytes of main memory
Booting flash:c870-advipservicesk9-mz.124-24.T.bin
Error opening: flash:c870-advipservicesk9-mz.124-24.T.bin
[code]....
I assume from this the required bin has either been removed, renamed or overwritten.As soon as the router boots it requires a password and I dont have the password to be able ftp files in and out of it.
View 10 Replies
View Related
