I've used many Cisco RV042/082 and have just purchased a couple previously used RV016 units.The first think I do is hold down the "reset" switch until the units reset to factory and then proceed programming them - EXCEPT this last unit doesn't seem to be resetting the administrative password.The unit has reset so that it is 192.168.1.1 and is handing out IP assignments via DHCP in that range.
When I point my browser (IE9) to the web page http://192.168.1.1 I am prompted to log on. I enter 'admin' for user name and attempt to enter the same for the password. The browser returns me to the logon prompt and after a few apparently failed attempts it displays a 401 error Unauthorized page.
and simply admin with a blank password.Isn't the admin password supposed to reset with everything else?If not - how can I - if it is, then what would be preventing the admin password from resetting - is there an internal jumper or something I could try? I don't care about preserving any setting obviously I just want access to the admin interface.
I'm trying to re setup my mother in laws Belkin F9K1002 wireless router. She has no clue as to what her password is for the wireless network or any other Belkin password. When I go to the support website, there are instructions to reset the network password, but you have to login to change the settings. The instructions say to leave the password field at the login blank but when I leave the field blank, I get an error message "Incorrect password. Please confirm your password and try again." So it seems I need the password to reset the password.
I need to reset the channel on my N300 router but in order to do so, I need to log in. The log in screen does not take my existing password. How do I get my current password or reset my password? It should be the simplest thing, but I have found this to be extremely difficult with Belkin.
i forgot my password for my belkin n150 wireless router so now it wont let me change any of my settings.i called tech support and all they wanted to do is get into my computer and sell me security progams .when i told them no they wouldnt reset my password and hung up.
Have a Belkin F6D4230-4 Version 3, both times we have stayed here we have noticed the same issue, we can connect to the router, but after a while it throws everything offline, and then you will see the orange light on the front of the router flashing. I usually have to reboot the router to get it to come back online. I did check the firmware version and it is the latest version 3.0 something, but it did say it was the latest?
I recently got a Belkin N150 Enhanced Router Model F6D4230-4 V1. I upgraded it to the recent firmware.
I use it NOT to access internet, but only to hook up my desktop computer with my laptop and my tablet PC. I use Win7 Ultimate on both computers. I configured a Win7 home network and I managed to access shared files between the 3 devices.
However, the speed is very very low, not going over 1.5 MB per second , sometimes even less, although the signal strength is the maximum (54).
The distance between the laptop and the desktop is only 4-5 meters, in the same room. My laptop is HP Compaq 6710b which has what seems to be a "Intel(R) PRO/Wireless 3945ABG Network Connection" .
Transfer speed is the same whether transferring from or to the laptop. I configured the laptop according to the instructions in the manual.
i have a belkin wireless router F6D4230-4. the "wired" and "router" lights are green but the "wireless", "modem", and "internet" lights won't come on. when they do, its red. the router is connected but won't pick up in any other rooms or on our phones.
I have xfinity internet with a comcast rented modem connected to a personally owned belkin router. I can successfully connect to the internet directly from the modem or if I connect to the modem to the router and then to my computer via ethernet cable. I cannot for the life of me connect wirelessly with any devices. The router previously worked when it was hooked up to comcast internet, but it was moden->router->my router. When I connect wirelessly on my Windows 7 laptop, it says I connect and that there is internet access. But when I try to load a page it takes me direclty to this website: url.. Comcast says that it is my router that needs configuring properly with xfinity and wants to charge me $39 to provide this wonderful service.
Router: Belkin Model F6D4230-4 v1 with firmware F6D4230-4_WW_1.00.03
so my xbox cannot connect to my router via wifi..the password has been tried and tried and restarted and to no avail.. i look towards my model F6d4230-4 and the light labeled "wireless" is flashing red. and yet my laptop connection is just fine. how do i fix the flashing red "wireless light" on my model: f6d4230
My main networking device is the Ericsson T073G HGU ONT, and when I am connecting to the network through the Ethernet there are no problems. However when I connect my Belkin F6D4230-4 router to it (through cable) my router cannot recognize the modem.I have tried literally everything.
I have to reset/recover admin-CLI password. I had posed the question in [URL]Now as per the CLI-admin password recovery procedure at [URL] I have inserted DVD in the hardware appliance, but I don't see any prompt with these options:
"Welcome to Cisco Identity Services Engine - ISE 3355 # To boot from hard disk press <Enter> # Available boot options: "
I just see login prompt ( and of course, I cannot login because I don't know the password). I am using serial console connection to the appliance.
I have a used wireless belkin router no cd with it i am using it now however anyone has access as i dont know the previous owners password i was wondering if i set it to default factory setting what it would do its model number isF5D7230-4 and im running windows 7 i tried you tube and they walked me through cmd then ip config then it walked me through login no password and i followed entire vidio several times it does not work?
There is a Linksys RV016 router setup at my workplace. I need access to the webmanagement interface however the default password is not working. (Username/Password: admin/admin) Is there any way to obtain the login information without performing a reset of the router so I do not lose its current configurations?
According to the Belkin support tech, apparently the weather (?) may have effected my Belkin Model F5D8235-4 v3 router. My wife pressed the re-set button instead of powering down which according to the tech set my router to reading zero (0).Belkin tech refused to tell me how to re-set the router unless I paid $75 for a six month support plan because mine expired recently.
I've just hooked up my previously used N300 router. The router is showing a solid green light, and the laptop recognizes that a solid Belkin wireless connection is out there. I cannot for the life of me remember the network key and/ or pass phrase I originally set. No, I did not tape this info to the underside of the router as suggested in Belkin instructions.
I upgraded my internet connection through charter and they shipped a new modem. Installed my new modem and my 300n will not connect to it. So in my attempts to figured things out I went it in and set it up as an access point only. I can access the internet on my desktop but there is no wireless signal in the house. Cannot connect to 192.168.2.1 now either. Tried the manual reset to factory defaults with no luck. At this point all I get is the small flashing blue light and the tall skinny light is not on at all.
Is there a way to avoid network interruptions when resetting the F5D8235-4 v3 router? I was hoping to find a config file or some other way to avoid having to reset the home network and devices. The administrator password has been lost, so i would like to reset that only and not restore factory settings.
Why My Belkin Router F5D8236-4 Ver 2 always rebooting itself. the router lamp is on and then the security lamp is on and then the router rebooting itself. this happening because im push the reset button. im already try to upgrade the firmware with recovering tool (Boot Loader / Tiny Kernel Version v0.02) from 192.168.2.1 but the problem still happening.