I've used many Cisco RV042/082 and have just purchased a couple previously used RV016 units.The first think I do is hold down the "reset" switch until the units reset to factory and then proceed programming them - EXCEPT this last unit doesn't seem to be resetting the administrative password.The unit has reset so that it is 192.168.1.1 and is handing out IP assignments via DHCP in that range.
When I point my browser (IE9) to the web page http://192.168.1.1 I am prompted to log on. I enter 'admin' for user name and attempt to enter the same for the password. The browser returns me to the logon prompt and after a few apparently failed attempts it displays a 401 error Unauthorized page.
and simply admin with a blank password.Isn't the admin password supposed to reset with everything else?If not - how can I - if it is, then what would be preventing the admin password from resetting - is there an internal jumper or something I could try? I don't care about preserving any setting obviously I just want access to the admin interface.
There is a Linksys RV016 router setup at my workplace. I need access to the webmanagement interface however the default password is not working. (Username/Password: admin/admin) Is there any way to obtain the login information without performing a reset of the router so I do not lose its current configurations?
How to reset the admin password on a tumbleweed appliance. My company just purchased a building, and the previous tenant left behind a bunch of equipment.
I have to reset/recover admin-CLI password. I had posed the question in [URL]Now as per the CLI-admin password recovery procedure at [URL] I have inserted DVD in the hardware appliance, but I don't see any prompt with these options:
"Welcome to Cisco Identity Services Engine - ISE 3355 # To boot from hard disk press <Enter> # Available boot options: "
I just see login prompt ( and of course, I cannot login because I don't know the password). I am using serial console connection to the appliance.
We are deploying a new batch of RV016 with the latest firmware (4.0.4.02). We are using 3 WAN ports for internet access (WAN1, WAN2, WAN3)The WAN ports connects to Cicso 800 series adsl modem with DHCP.The RV016 WAN1 port setting regularly resets to 0.0.0.0 despite that the modem dhcp is still up and running. A cold boot, resets all the configuration and WAN1 port start working againg a new ip.
All three WAN ports are set to automatically obtain ip from the modems.We have tried several modems, and even swap WAN ports, but the error is persistant to WAN1 only.
WAN2 and WAN3 are up and running without any errors. This error is persistant with WAN1 only.We have also configured a manual ip on WAN1, and after a few hours of operation on all 3 ports, traffic on WAN1 comes to a halt.We have the same error on 3 units we received last week.All there modem are configure on different subnets.It does not seems to be a configuration error with the modem as they work perfectly well with the WAN2, WAN3 ports.We also tested a RV016 out of the box using the wizard setup, without any extra setting/configuration, and we got the same error after a few hours of operation.
I have in my work RV016 10/100 16-Port VPN Router, working Ok and connected with 3 ADSL internet lines.
1- The problem is that when any line disconnect from internet it supposed to log this disconnection in internet in system log but it does not
2- I can't understand the option of sending mail with the logs, does it send when i press the button EMAIL LOG NOW, or it supposed to send when any log is added? and how to configure it.
what to do with my router cdr -king i cant access 192.168.1.1 in second time. i access it for the first time but i forgot to configure password now i cant connect using ID:admin Pass:admin
I have a belkni F5D Router and I have lost the password to access it. I dont have any computers or devices that still connect to it, and I really need to know how to hard reset the password!
I'm trying to re setup my mother in laws Belkin F9K1002 wireless router. She has no clue as to what her password is for the wireless network or any other Belkin password. When I go to the support website, there are instructions to reset the network password, but you have to login to change the settings. The instructions say to leave the password field at the login blank but when I leave the field blank, I get an error message "Incorrect password. Please confirm your password and try again." So it seems I need the password to reset the password.
I need to reset the channel on my N300 router but in order to do so, I need to log in. The log in screen does not take my existing password. How do I get my current password or reset my password? It should be the simplest thing, but I have found this to be extremely difficult with Belkin.
i forgot my password for my belkin n150 wireless router so now it wont let me change any of my settings.i called tech support and all they wanted to do is get into my computer and sell me security progams .when i told them no they wouldnt reset my password and hung up.
I have a conflict with my satellite Internet connection between the modem and router IP addresses. I also somehow entered a password for the router which I now cannot duplicate. received a request for additional information which I responded to in September. I attempted to follow-up in October again, but I have not received any reply since the first one on August 11, 2011.
I upgraded the firmware for my WRVS4400N v2 to version 2.0.2.1 firmware, now old and default passwords don't work. I have tried resetting it as well, and the default password does not work.
I have a linksys wrt54gs wireless router (working fine since last 3 years) which connects to the internet fine if there is no password set. However if i set WEP password to protect the wireless connection, i am not able to connect to the wireless connection. Everytime i enter the passphrase, when trying to connect to the wireless network, it refuses to accept the password. I have tried this with 2 laptops (both running windows 7) and both have same issue.
We have around 70 1131's on our 4404 WLC and there are around 5 of them which always seem to reset themselves to Admin Status = Disable. They are in H-REAP mode as are all the other AP's, but for some reason I have to keep going in and setting the Admin Status of the AP to Enable. This has been occuring across different firmaware versions since 4, we are currently running 7.
I have a small, wired office network. Win 7 platform - I upgraded a pc from Vista to Win7 Ult. Now in order for 2 of the office personnel to logon to the network,they must first supply an admin password each time. I am the administrator so I can do this for them, but I can't keep doing this every time they need to login.
I recently switched ISPs, and the new one gave us a Ubee DVW3201B as our home gateway. I want to change the Administrator username/password from the defaults, but I've been having some difficulty.
Every time, after I save the new username and password, I'm prompted to re-authenticate to the administration interface. It fails no matter what I try. I've tried using:
New username / New password Default username / New password Default username / Default password
None of the above works. This has happened twice now, with my only recourse after failure being to do a reset to factory defaults (press and hold the hard reset button for 10 seconds).Is there something I'm missing?
We installed one Extreme Network's 'Summit X450e-48p' switch in our organization. Unfortunately, we forgot it's admin account password and we don't have any other account on this switch to work on it.Anybody to guide us how to break admin account password for a Summit switch. We don't want factory reset.
I just recently bought a WAG160N and I have a big issue with it, I can't change the password for the default admin account. All I get is this error in the browser "Error 324 (net::ERR_EMPTY_RESPONSE)"
Quick reset.Power cable disconnect for 60 sec.Factory reset followed by a reset of the router for 60 sec.Clearing my browsers cookies and internet temporary files.Only things I have changed is the Basic Setup to get connected to my ISP and the Wireless settings.
Details about clients, firmware versions etc.
Windows 7 build 7601 Service Pack 1 Chrome Browser 16.0.912.75 Wireless-N ADSL2+ Modem Router V2 firmware version 2.00.20
Im having some problems changing my admin password on my DCS920
I know the default login is Login: admin / Password: "blank"
So I go into maintence, and there's an option to change the password.
it lists:
old password newpassword confirm
So I leave the old password blank and type in my new password in the following 2 spaces. I click apply and a window pops up asking me to enter username and password. I just enter admin and leave the password blank. I hit ok, and everything seems to update ok. So i log out, and try to log back in.
A window pops up asking me for my password. I type in admin for my username, and my new password, and it wont work
I type leaving the username blank, and type in new password... WONT WORK
I type admin, and new password again.. WONT WORK
I try password with first letter capital.. WONT WORK
I try password with ALL CAPS... WONT WORK..
Basically it wont let me log in as admin anymore. I figure I may have typed the password wrong the first time so I reset the camera and try the process again.. SAME PROBLEM.
Am I doing something wrong in changing my password ?
I dont wanna leave my default admin login as admin/"blank" , but when I try and change the password, it wont let me log in again as admin.
I just got a WRV 210 wireless router (three of them actually, planning to set up a VPN). But I can't set the admin password. I've tried 4 times, and every time, i've got to hold the reset button to reset to factory settings in order to access the management pages! I enter the new password in both fields, and then click to save the settings. It restarts. Then i try to log in - and it doesn't accept the new password. It doesn't accept the default password. I've tried with admin/(new password) and (new password)/(new password), and admin/admin. None of them work, forcing me to reset router to factory settings. I've tried a password composed of 6 letters followed by a . Thinking that maybe the . was throwing it off, I tried 6 letters followed by 3 numbers. That doesn't work either. I've updated to firmware version 2.0.1.5. No luck.
