We have around 70 1131's on our 4404 WLC and there are around 5 of them which always seem to reset themselves to Admin Status = Disable. They are in H-REAP mode as are all the other AP's, but for some reason I have to keep going in and setting the Admin Status of the AP to Enable. This has been occuring across different firmaware versions since 4, we are currently running 7.
View 1 RepliesI have WLC 4404 Controller with 180 LWAPP. i want to disable Broadcast SSID from some specified APs not all. is it possible to do that with 4404 WLC controller.
View 9 Replies View RelatedWe have 1242-AG series AP which is configured in Rogue Detector mode. After adding this AP to WLC its showing Admin Status of AP as Down.
When i am trying to enable the Admin Status its giving me following error
" Admin status cannot be enabled for AP in Rogue Detector mode".
how to enable Admin Status for Rogue Detector AP.
1552 E Ap with a 2504 WLC. Single Root Ap with Mesh the Mesh has the problem. Both Power Injector and AP has been replaced . How do you turn on the 802.11 B Radio? No other problems at 40 other sites with identical installation.
View 1 Replies View RelatedI have a AIR-LAP1131AG-A-K9 this Ap is registered but, i cant enabling admin status on interface B/g, when select option throws a error. "Error in Enabling Admin Status"
View 4 Replies View RelatedI work on photocopiers and sometimes I get an error code that's not in the service manual.[URL]contains some useful information so I use Google to search the forums for example:It has recently stopped working on my computer and another at work. Copytechnet loads breifly then windows says unable to connect to site and internet explorer closes.
View 1 Replies View RelatedWe have two autonomous access point 1142 series running 12.4(21a)JA1 and randomly the Dot11Radio0 interface goes into reset/down state. At first I thought it was something related to power consumption issue on the switch, but looking at the remaining (w) I have plenty.
View 8 Replies View Relatedhow to totaly disable Admin/ASDM access on our public interface of our 5510. I don't want to change IPSec or SSL access to the outside interface. Just totaly disable access to Admin/ASDM from the outside without halting all other access.
View 3 Replies View RelatedRegion : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :
Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.
This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
ap03#
ap03#
ap03#sh ip int brief
[Code].....
I have a 1 month old SG200-26P - the green status LED is blinking constantly (> 30 minutes), I cannot access the webGUI, nor is it responding to ping. I have tried resetting via holding reset for > 10 seconds with no effect, the status/activity LEDs are still illuminating against all connected ports, excluding any of the PoE ports which are running a couple of cisco IP phones. I've tried accessing the device via both the static IP I configured, and the default IP.
I have disconnected all ports, then powered on the device, but same results...Do I have a dead switch? Anything I can do other than return for warranty claim which is going to be last resort due holiday period and leaving the customer offline for extended period...
I have a 1 month old SG200-26P - the green status LED is blinking constantly (> 30 minutes), I cannot access the webGUI, nor is it responding to ping. I have tried resetting via holding reset for > 10 seconds with no effect, the status/activity LEDs are still illuminating against all connected ports, excluding any of the PoE ports which are running a couple of cisco IP phones. I've tried accessing the device via both the static IP I configured, and the default IP.
I have disconnected all ports, then powered on the device, but same results...
Do I have a dead switch? Anything I can do other than return for warranty claim which is going to be last resort due holiday period and leaving the customer offline for extended period.
I reset my WRT120N and after rebooting i entered user name :admin /password:admin as usual but it refused my access.
View 2 Replies View RelatedI have to reset/recover admin-CLI password. I had posed the question in [URL]Now as per the CLI-admin password recovery procedure at [URL] I have inserted DVD in the hardware appliance, but I don't see any prompt with these options:
"Welcome to Cisco Identity Services Engine - ISE 3355
#
To boot from hard disk press <Enter>
#
Available boot options: "
I just see login prompt ( and of course, I cannot login because I don't know the password). I am using serial console connection to the appliance.
I've used many Cisco RV042/082 and have just purchased a couple previously used RV016 units.The first think I do is hold down the "reset" switch until the units reset to factory and then proceed programming them - EXCEPT this last unit doesn't seem to be resetting the administrative password.The unit has reset so that it is 192.168.1.1 and is handing out IP assignments via DHCP in that range.
When I point my browser (IE9) to the web page http://192.168.1.1 I am prompted to log on. I enter 'admin' for user name and attempt to enter the same for the password. The browser returns me to the logon prompt and after a few apparently failed attempts it displays a 401 error Unauthorized page.
In desperation I have tried:
admin / admin
/ admin
admin / password
/ password
admin / rv016
and simply admin with a blank password.Isn't the admin password supposed to reset with everything else?If not - how can I - if it is, then what would be preventing the admin password from resetting - is there an internal jumper or something I could try? I don't care about preserving any setting obviously I just want access to the admin interface.
How to reset the admin password on a tumbleweed appliance. My company just purchased a building, and the previous tenant left behind a bunch of equipment.
View 4 Replies View Relatedi forgot my admin password and i want to know if there is a way to retrieve or reset it. I have the enhanced wireless router model F6D4230-4 V1
View 3 Replies View RelatedDoes any know what " Last reset from system-reset " means? Is this becouse of a power failure or someone reloading the switch?
View 3 Replies View RelatedI have the WAP11 serial number G3110320414 that does not have a reset switch in the back. How do I get back to factory settings?
View 3 Replies View RelatedI need to upgrade our Wireless Lan Controller to support new APs. I was able to get the new code due to a security advisory on the code we are running now. I am upgrading from 6.0.196.0 to 7.0.220.0 (MD). I have read in some of the technical docs that the WCS has to match the WLC. I cannot find any documentation as to what this entails on the WCS.
WCS version is 6.0.132.0 running on Windows.
We have two 4404's and WCS. The 4404's are almost maxed out. We have an addition 4404 which we would like to add to the group of 4404's
View 1 Replies View RelatedI have a Cisco WLC 4404 with version software 7.0.230.0 and it gived me a this logg
Oct 9 15:43:08 192.168.122.34 WLC_4404_CC: *osapiReaper:
Oct 09 15:41:49.549: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/895/stat.(erno 24)
I have a WLC 4404 installed and we would like to manage the bandwidth per SSID.
Today we have configured many SSID because our campus has a lot of wireless users and any SSID has only one class C subnet (/24).
We would like to configure each SSID with more subnets. is this possible ?
Additionally we need to restrict the bandwidth per SSID. is this possible ? We have some SSID for less important users and we would like to assign the bandwidth per SSID.
I have a Cisco 4404 WLC that is up, has green status light, the interfaces are showing activity. I see it connected to my Cisco 6500, (Sh port status) it shows connected and trunking,; I also see a lot of activity on the interfaces. Also it will not let me console in, I can console in on my other Cisco 4404 WLC's with out and issues, so I know my cables and configure are correct. The only change a I made today was the time zone. I noticed the time was off by a hour and noticed that the time zone wasn't set so I set it correctly. Shortly after that I saw the WLC go belly o up in my WCS. I tried rebooting the WLC several times without luck. Since I can not gain access via the console I can not really trouble shoot.
View 10 Replies View RelatedTrying to upgrade my Wireless LAN controller model 4404, I'm running 4.1.190.4 code and want to upgrade to 6.0.202. Looking at the release notes for 6.0.202 and the compatibility matrix, the matrix indicates I two intermediate loads first. One is 4.1.192.35m and the other is 6.0.182.0 then I can load 6.0.202 code. My problem is I can't find the 4.1.92.35m code. Looking at the software download the highest 4.1 folder has is 4.1.185.0. where to find the 4.1.192.35m code for 4404 WLC?
View 1 Replies View Relatedwe have cisco wlc 4404. and we want to access it thru internet.
i have attached the management interface screenshot.
WLC 4404 is configured as Anchor controller, the MAC violation are captured by Controller. the Violated MAC are deleted manually through GUI, but when tried deleting through CLI using command
>Config exclusionlist delete <mac address>
we get error message as error deleting user <mac address>
We have 2 4404 controllers running 6.0.x code. I have several SSID setup with different VLANS. When the clients associate they do not show the name of the AP they are connected to, is there any way to display the assocated AP name?
View 2 Replies View RelatedI got a WLC4404 running software version 5.1.151.0 with 40 LWAPPs (mostly 1242AG). We got new Dell Latitude E6500 Laptops with Intel 5100 NICs. After upgrading the bios to the latest version and installing the latest wlan driver, wireless is working the most time.After about 4 reboots I see the following message in the WLCs logfile: "Thu Sep 18 13:53:10 2008 AAA Authentication Failure for UserName:host/hostname.domain.name User Type: WLAN USER".After I disable the wlan-card, it's working again.
View 7 Replies View RelatedI am facing a strange problem in my WLAN Setup. none of my wireless clients are able to associate with Wireless LAN but when I delete and create a new wireless profile in WLC 4404 clients starts associating with WLAN. every 2-3 days I had to delete and create wlan profile. Is it related to IOS bug or any other problem? My Wireless LAN Controller image is AIR-WLC4400-K9-5-1-151-0.aes.
View 4 Replies View RelatedUpgraded our WLC 4404 from 6 to 7 so we could upgrade some WAPs to 3500i. After upgrading all 8- 1120 and 1240s connectivity were lost.
We reverted back to OS 6 and all came back to Controller
WLC Software version = 6.0.199.4
WLC Emergnecy Image Version = 7.0.235
[Code].....
Our vendor states this should be a compatible mix and they are also checking as to why it is not working as planned.
I have a 4404 with 3 SSID's configured on it. I only want all SSID's to be available on one floor in one building and not on any other AP's in any other building or floor.I thought the way to do it was via AP group but have not had any luck getting that to work. I setup a group for the AP's that I do not want all SSID's and then assigned those AP's to that group. However, I can still see all three SSID's where I only want to see 2 SSID's.
View 4 Replies View RelatedI've downloaded Prime Infrastructure 1.2 eval and wanted to see what it looked from WCS that I am currently using to manage the wireless network and I added the WLC (4404) device but it list the device as "Managed with Warning" and I can't find what the warning is.
View 3 Replies View Related