My HP printer finds my network, signs on just fine, has internet. My 2 wired PCs are connected and have internet. My 2 wireless laptops find the network and have internet. Everything has internet successfully thru the router....not one of them can print anything because not one of them can see the printer that I know is there.
View 3 RepliesI have a home network with a Netgear N600 as my main router. I have a wirelesss HP printer that accesses fine as does Iphones and Ipad. Then I have hard wires. Off of the main router I have 3 Netgear 5 port switches. 1 switch with a line to bedroom tv and a line to family room tv. 1 Switch at family room TV which goes to Blu Ray, Direct Tv, and Xbox360. 1 switch at bedroom for Blu Ray and Direct TV. Believe it or not, this all worked. I tried to hook up a ZmodoH264 security system (the ones with four cameras, and a separate hard drive and monitor for viewing). I used one of the 4 inputs on the main Netgear router for this, and it seemed to be recognized. But, I can't access the security system mobilly, AND all my network addresses seem to have been screwed as Directv isn't working (Whole Home) and the printer stopped being recognized. However, Blu Rays are still fine. Is there a way with ipconfig to list all of my hard wired nodes? I assume wireless dont show up in a list.
View 4 Replies View RelatedTrying to get my Netgear N600 router to connect to the internet...nothing will get it to connect.I am able to follow step-by-steps to resolve this
View 14 Replies View Relatedhow to wire a netgear n600 to a U-verse router in order to strengthen the wifi signal
View 1 Replies View RelatedI puchased the N600 WNDR3700v3 Dual Band Gigabit Router. I am able to see my wireless account I set up and is out there to connect to, but I cant connect. I can connect with an ethernet cord, but nothing wireless. It doesnt work for my home or work laptops. Prior to this I had another wireless set up and I am tempted to plug that one back in.
View 1 Replies View RelatedJust bought a new Netgear N600 router, hooked up 4 wired computers with no problem and got several wireless devices to hook up without issue. My laptop however, will not give me internet access when accessing the network wirelessly.
The access is labeled as Local Only, and the network is considered unidentified. Signal strength is excellent, and it reads the name of the new wireless server I created. It prompted me to enter the passphrase, which I did, and now my laptop is stuck on local only.
I tried updating my adaptor drivers but they are all up to date, and I tried to enter my adaptor into the address reservation on the router configuration page using the laptops MAC address and IP address.
My son just got an Asus Laptop from his school. It is running Windows 8.It connects to other peoples WIFI, just not my home WIFI.When he got it home he found the network, entered the password and nothing happened. Now it can't even find the network.There is nothing wrong with the router as every other device connects fine.The router is a Netgear n600 - DGND3700?
View 3 Replies View RelatedI have a netgear n600 router and in the room its in i get around 50 down and 12 up but in other rooms it drops significantly(the highest ive gotten is 11 down in other rooms). is there any setting i can go into.
View 3 Replies View Related[CODE]My router stopped working when I tried to connect my new Samsung Smart TV to the wireless network by using the menu on the tv. I had to go and press the WSL button on the router. I pressed what I though was the WSL button and now my router doesn't work. I has three lights lit up, the power on light, a small green blinking light and an amber light by the number 1.I've gone to the Netgear website and they want $69 for assistance to get my router up and running. I can buy a new router for that much money. There has to be an easier way.
View 2 Replies View RelatedI tried using an ethernet cable (cat 6) to connect my laptop (Sony VPC-1190X) to our gigbit router (Netgear N600 WNDR3800), but I get a message that there is no internet connectivity and the light representing that port on the router does not turn on.So, dead ethernet port on the router? Nope - unplugged the working printer from the router and used that ethernet port - same result.so dead ethernet port on the laptop? Nope - plugged the laptop into a gigbit switch (D-link DGS-2205) and instantly got internet connectivity. Note that this switch is plugged into the aforementioned Netgear router.For good measure, I tried power-cycling the router and laptop.
BTW - I can connect the laptop to the router wirelessly but I am trying to make use of the faster transfer speed of the ethernet connection.
My net drops off every 20secs like clockwork, only affecting the wireless.I bought a new router yesterday to see if that would work, but it hasn't. At the moment, my router is connected to the modem, and my computer upstairs is running through the wireless connection from the router (not the modem)
My router is a NetGear N600 Wireless Dual Band... and my modem is a NetGear Rangemax wireless My computer is running Windows 7 and has a Realtek RTL8191SU Wireless LAN 802.11n USB 2.0 Network Adapter(im connecting to my network via the 2.4ghz... not the 5ghz)I've tried doing the whole, ipconfig/ release
I previously had DSL with my own combo modem/wireless router. I cancelled DSL and got Cable broadband instead. I've already unplugged my DSL modem/router and have my cable modem hooked up, all is running well. I bought a new Netgear N600 wireless router that I want to set up. Do I have to uninstall any software or files from my previous DSL modem/router before installing my new cable router?
View 3 Replies View RelatedI have internet through my cable company and currently use their wireless netgear router. I purchased a Netgear Router N600 but it does not have a port for the cable connection. Can you recommend the correct wireless router
View 1 Replies View Relatedwhat is the WI-fI Network name (SSID) and Network Key (password) of my Netgear N600 Wireless Dual Band Router WNDR3400v2
View 1 Replies View RelatedHow do I change the UPnP setting on my router?
View 2 Replies View Relatedabout two days ago my main PC lost the ability to connect to the internet. I'm useing a trendnet tew-687ga adapter and a netgear n600 router. I can't ping the default gatway 192.168.1.1
View 2 Replies View RelatedI recently put in a Netgear firewall, configured it, its running no problem. Then I setup a new Netgear N600 wireless router, configured it, gave it a static IP, connected to it, works like a charm. Thing is, when I try to access the web gui I receive nothing.. Is the Netgear firewall taking priority or something? I went directly connected to the netgear wifi router and double checked to make sure that there was no settings restricting administration from wifi users, etc..
View 3 Replies View RelatedI got new internet last Thursday. It is fiber optic through VTX1. I am running windows 7. I can connect to the internet just fine directly but when I try the netgear it tells me No Internet Connection. When I go through the setup process it tells me No Ethernet Cable is Plugged Into The Router Internet Port. When I hook up my very old Cisco router the internet and Wi-fi work just fine. I have updated the drivers and have windows firewall off. This is it plugged directly in:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersKellan>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Kellan-PC
Primary Dns Suffix . . . . . . . :
[code]....
I have cable broadband internet. My internet modem is a Ubee D3.0. It is connected to my Netgear N600 Wifi router which have my computer and DirecTV hooked up to it via ethernet. My wifi went down the other day. Devices were connected, but were not getting any internet service. In troubleshooting, I attempted to dial in to the router using www.routerlogin.net as well as 192.168.0.1, and I could not get into the router. I assumed the router must have crashed, and I only purchased it a month ago, so I took it back to the store and exchanged it for a new one. I got home and plugged it in, still not working. I can't access it using the above mentioned methods, and the setup software does not detect a router present. I unplugged the router and hooked the computer up directly to the internet modem. Still no luck. The computer does show a network connection in the system tray, but with no internet. I plugged my laptop in to the internet modem, and I am able to get internet just fine from my laptop. I even did a system restore to a restore point last week when I know the internet was working. No luck.
View 5 Replies View RelatedI have a PC modem and recently purchase a netgear N600 wireless router. Do they make a splitter of some sort. So I can use both the PC and IPad? If they make a splitter?
View 5 Replies View Relatedi've been tring to configure our netgear N600 router, it directs me to the support homepage all the time after we half through the configuration and got disconnected at first try. now i've tried clean dns, reset internet settings, nothing seems to work...
View 1 Replies View RelatedI have a Netgear N600 Dual Band Gigabit Router and my roomate and I both have the wireless xbox and when we connect to xbox live and find a game on call of duty mw2 we lagg our butt off nd we tried changing the channel on the router but it still seems to lag.
View 11 Replies View RelatedI confused ,with which modem to purchase to set up my n600 wireless dual band gigabit router wndr3700, i'm on boardband with no modem
View 1 Replies View RelatedI have a Netgear N600 WNDR3700v1 Dual Band Gigabit router and am having a problem with the wired connection with my PC. Everything wireless in the house works fine. In fact, I also have a Direct TV box hooked up for on demand and a sling box hooked up (both wired) and they work find. It's just my PC that is having issues. If I bypass the router and hook straight into the modem, it runs fine also so I have something going on between the router and this PC. I updated the NIC driver and this did not work. Before the update in the device manager, it said it was a NIVIDA nForce Network Controller (if I remember right) and now it says NIVIDA nForce 10/100 Mpbs Ethernet. It was suggested that I change my speed and duplex to match the router after I update but I am unsure what to change it to.
View 11 Replies View RelatedI use a Netgear FS605 Ethernet Switch to connect a wifi modem to my network and thus to the internet. People in that room can jump online via the wifi modem. You can also print to the wireless printer in that room via that wifi modem being local. However, I can no longer print to the wifi printer from anywhere else in my network (I could before I got a new router and wifi modem in there).Would this be a problem with this Switch or with the modem e.g.
View 1 Replies View RelatedI have a Canon i6700d, which I connect to the belkin N600 USB port to share on the network. Driver for the printer is installed. From the belkin router monitor, the printer is listed under "Networked USB devices". However, the printer is grayed out and can not be selected. the dialog complains that the printer is not available.
View 1 Replies View Relatedwhats better netgear n600 wireless dual band router or netgear n750 wireless dual band gigabit router?pretty much the n750 would be better because its the latest model but what would be the advantages of it and is it better for gaming than the n600?whats the dis/advantages of both of them?
View 1 Replies View Relateda few days ago my router was not working for wireless out of no where and its still not working. i only get internet on my main computer that its connected too. not my laptop ipod or tablet
View 2 Replies View RelatedI have a actiontec Wireless N ADSL Modem/Router Model# GT784WN & netgear n600 wndr3400v2 router that I would like to setup as a Wireless Repeater. I can not seem to get the netgear n600 setup.
View 1 Replies View Relatedmy netgear router is blocking my printer
View 1 Replies View RelatedIm on Windows 7 Ultimate, I have Netgear N600 and a motorola and all the lights are on but when I lose connectivity to my internet, everything looks fine light wise. My whole family connects to the wireless in my house and when the internet goes down, they too, are effected. The internet would be running for a few minutes and then sadly go down for a minute then come back up. This has been happening more and more lately and its come to a point where I'm sick and tired of trying to fix it myself. Its very aggravating to be surfing the web and one point and then seeing the oh so nice "Firefox cannot connect to your internet" screen. I play World of Warcraft, as of right now, its unplayable. I'm stressing because its just a hug hassle. The Motorola and the Netgear are fairly new and I don't seem to think that would be the problem.
Specs
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Ultimate , Service Pack 1, 32 bit
[Code].....
I just got a Nook Color as a gift (nice huh?) I just bought my iPad2 in Jan. So now I've got Comcast cable with a Netgear N600 router and:
1 desktop Win XP sp3 plugged into router
1 desktop Win 7 usb wireless
1 HP laptop w/ Vista
2 Dell old laptops Win XP not used much
Sony PS3 not on much
iPad2 always on
Nook Color
AND a Roku always on
I think that's all. So I'm guessing all this will slow down my whole connection? My iPad is the fastest. My Nook is extremely slow. Maybe it's the B&N website? When I go to shop and even when I registered it, it says connection having trouble. I finally had to setup my account at BN with my desktop. The Nook wouldn't stay connected.
I have an iMac running 10.4.11. I would like be able to print through the router. I now have my PC laptops doing so. What voodoo do I have to do to make the iMac work with it?
View 3 Replies View Related