Motorola SBG6580 Gateway Acting As Router / Wireless Access Point?
May 4, 2012I cant seem to to connect to my nintendo i have a motorala surfboard SBG6580
View 1 Replies
ADVERTISEMENT
Motorola SBG6580 / Using A Gateway As A Access Point / Router
Mar 16, 2011I switched to comcast internet recently and got a new modem. The modem is the telephony Arris one, but the problem is that I already have a Motorola SBG6580 but can not use that for my wireless laptop options. I want to be able to use the SBG6580 as my access point and LAN, but it isn't allowed any internet to share wirelessly?
View 3 Replies View RelatedMotorola SURF Board Gateway SBG6580
Oct 2, 2012Since the new cable company won't let me use my SB6141, I need to pick up a new cable modem. One that works with Oceanic TWC is the new SBG6580. It has wireless built-in; however, I don't want to use it. Is it possible to use this modem and leave the wireless off? Or does the wireless automatically turn-on whenever the modem is on? With all that said, is the built-in wireless any good? I recently purchased an ASUS RT-56 and would prefer using it to some built-in system.
View 11 Replies View RelatedLinksys Wireless Router :: Connect To EA6500 In Bridge Mode Acting As Access Point?
Mar 4, 2013How do I connect to the EA6500 once it's in Bridge mode acting as a wireless access point? Checked the posts and some seem to be able to do this but, we cannot.
View 6 Replies View RelatedRun Motorola Sbg6580 With A Netgear Wndr4500 Router?
Apr 26, 2012I have time warner internet service and just upgraded my service to their extreme internet. In doing so I had to change my modem to a docis 3.0 modem; the motorola sbg6580. Its a modem that has a router and wifi built in but its really bad and not nearly as good as my net-gear router.
View 6 Replies View RelatedNo Internet Access After Connecting To Sbg6580 Gateway?
Mar 4, 2013Acer aspire 7741Z-4633 with windows 7 connects wireless to sbg6580 gateway that was just installed, but no internet access. able to connect other devices.
View 1 Replies View RelatedAdding Belkin N Wireless F5D8236-4 To Motorola SBG6580
Jan 7, 2012Looking to add my belkin wireless router to Sbg6580 router as an access point to extend wireless. I've read up enough to understand the fundamentals - LAN to LAN, changing IPs, turn off DCHP etc. - but am confused by a couple of things.
First, belkin faqs says to Open the router page, click on "use as access point" (I get that) "Select Enable" (I also get that), and then it goes on to say "This will give you the options to set the IP Address and Subnet mask for the router.**These settings should match your existing network settings; by default the IP address will be set to 192.168.2.254 and the Subnet mask will be 255.255.255.0". Does this mean to set the IP address of the Belkin to that of the Motorola (which is 192.168.0.1) on this page?
Then the FAQ goes on to say access the LAN and "change the IP Address to something such as 192.168.2.47 or you can use 192.168.2.200.**As long as the first three sets of numbers match your existing network, you will be fine". I thought the LAN IP address should fall outside the DCHP range of the Motorola? So if the DHCP range for the Motorola is 192.168.0.2 through 192.168.0.250 then I'd assign 192.168.0.251 to the Belkin?
Motorola SBG6580 / How To Change The SSID
Mar 12, 2012Motorola SBG6580, How do I change the SSID?
View 1 Replies View RelatedMotorola Sbg6580 Configured With Vonage?
Dec 9, 2011Can the SBG6580 be connected to the Vonage router and function?
View 1 Replies View RelatedMotorola Surfboard SBG6580 / 2nd Computer Keeps Randomly Disconnecting From LAN?
Oct 12, 2012I have a 2nd computer wired up to my modem, but the LAN keeps randomly dropping every 2-5 hours It never drops for my main computer.I tried swapping cords and ports, but it still disconnects, while my main computer remains connected The internet worked fine when connected to another modem in another house.Do you think this is a problem with the modem or Windows7?I hard-reset the modem to factory settings, but it still happens.the modem is a Motorola Surfboard SBG6580
View 1 Replies View RelatedMotorola SBG6580 Where To Download Software To Configure Network
Jun 30, 2012I am missing my Installation CD, where I can download the software to configure my network (rename, etc.)?
View 3 Replies View RelatedMotorola SBG6580 Surfboard :: Port Forwarding Minecraft On This Device
Jul 30, 2012How do you port forward Minecraft on a Motorola SBG6580 because I tried it and it didn't work I really want to have my own minecraft server,Dont say to go to portforward.com because I tried it and it didn't work it says the port is still closed when I check it on yougetsignal.com
View 5 Replies View RelatedLinksys Wireless Router :: Can't Set Default Gateway On WRT310N In Access Point
Jul 28, 2011I am using a WRT310N. I have a Cisco ASA5505 as my firewall and don't need the routing capabilities of the WRT310N. So I just plug the LAN port on the WRT310N directly to my LAN switch. I just need the WRT310N to have an IP address for management. So I configure the LAN with an IP address, but there is no way to set the default gateway on the LAN. You can only set the default gateway on the WAN interface, which I don't use, since I am using this in an AP only type of configuration.
View 1 Replies View RelatedLinksys Wireless Router :: E2500 And Motorola RG2200C Residential Gateway?
Jan 6, 2013I am trying to setup a Linksys E2500 router with a Motorola RG2200C Residential Gateway. The Motorola box provides TV and DSL output. Currently a Linksys BEFSR81 router is connected and works fine. With the E2500, running Cisco Connect it gets to 90% complete and then times out. I'm guessing at that point it is trying to connect to the Internet.Support had me download the latest Cisco Connect, but it had the same problem. I have tried various things manually configuring the router with no success.
View 9 Replies View RelatedMotorola AP5131 - Access Point GUI Fail
Feb 8, 2012I am employed at a small business, 30 employees, and they just fired the IT "liasion". Guess who the new one is... So we have RF barcode scanners that run off of access points that have high gain antenna's WITH NO ENCRYPTION AT ALL. We are broadcasting a wireless signal to half of Ohio with no security what so ever. No wonder the last guy was let go. So, I have Symbol/Motorola AP-4131's with are easy to serial up to and configure. Love them for their ease of use but they only transmit 802.11b. The AP-5131 access points are 802.11 a/b/g but are total hell to work on. I have serialed up to the 5131 and restored the AP to factory defaults and can access admin level through the CLI just fine. Problem is I don't know the CLI so I need to access the GUI.
View 3 Replies View RelatedCompatible Access Point For Motorola SURFBoard 6580?
Mar 15, 2013I have a Motorola SURFBoard 6580 as my cable modem + router + 802.11n AP. I wanted to add an AP on the second floor of the house for better signal. I have read that APs from different manuafacturers are not necessarily compatible for seamless roaming. Well, I guess the worst case is to turn off wifi on the SURFBoard and get 2 identical APs, but that's not ideal.
View 2 Replies View RelatedLinksys Access Point :: WAP300N Conflict With Gateway / Router
Apr 27, 2013I recently purchased and installed seven WAP300N access points in a school, but they are now having intermittent problems with network access, as of right now their network is completely unusable. Specifically there appears to be a conflict between these access points and the gateway/router which provides their network clients with addresses via DHCP; BUT in the three years I have been assisting them the DHCP server on their Cisco router has never before given any problems!
All WAP300N units are wired to the network acting as standard access points and setup to pickup their address automatically via DHCP. When the problem first arose I changed to offending unit to use a static IP address to avoid what I presumed was an address conflict; however the same problem now appears to be happening with the other units as well!
My understanding is that these WAP300N units do not have any in-built DHCP server capability, is this correct ?If not, how I can disable this feature.Otherwise, it would seem to me that the units must be incorrectly using the default gateway address which they are getting from the DHCP server as thier own IP address. Unfortunately assigning static IPs to each access point is not possible as these are controlled by another group and the existing allocation is now used up.
Cisco WAN :: 2960 / Internet Access Router Acting As DNS Server
Nov 25, 2011I have a design for my infrastructure and i'm thinking to choose 4 or 5, or more, 2960 series in a stack mode instead of one 4500 series?
View 4 Replies View RelatedMotorola SBG 900 Wireless Surfboard Gateway?
Sep 4, 2011I use Motorola SBG 900 Wireless Surfboard Gateway with Timewarner service provider. I have couple of problems....
Problem 1 : I use VOIP phone (Vonage) which connected to my Motorola wireless device, current when i call somebody using VOIP phone, they can hear my voice but i cant hear them... Last years i dont have any problem but last one month above problem exists.
Problem 2: I tried Speed test with cable (13MBPS download stream) but through wireless (6MBPS download stream)
Linksys Access Point :: WAP610N - Gateway Is Not Working
Sep 20, 2011We have a several WAP610N Access points in our company since a few months and immediately noticed that it has problems with the gateway when you set it to use a static IP. (the AP loses its gateway when you pull the power). Today I saw that there was a firmware update, and in the firmware release notes it stated that the problem with the missing gateway info on the status screen was solved.
This info is correct. After updating to 1.0.0.2 the gateway is shown in the status screen when you use a static IP, but the actual function of the gateway is still not working after restarting the AP! I already let our reseller create a support call with Linksys a few months ago, but in the end they told me this would probably not be fixed and that I had to use DHCP.
Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?
Apr 16, 2013I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedCisco Wireless :: Point To Point Access Point 1262 Bridging
Feb 27, 2013How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedMotorola Router Cannot Access Other Computer
May 28, 2011I have a desktop, Sony VAIO laptop, and a Motorola router and modem combination. Both computers are running Windows 7 professional. The desktop is running the 32 bit version and the laptop the 64 bit software.When I first got my router, I could access my laptop from the desktop but after a crash on the desktop and reinstallation of everything, I can no longer access the laptop. I have set up file sharing on the laptop but it still will not allow access. Here is the message that appears when I try go access a folder on the laptop:"Windows cannot access \name-VAIOackups,You do not have permission to access \name-VAIOackups"
View 3 Replies View RelatedCisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point
Apr 20, 2012I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedLinksys Wireless Router :: SBG6580 And E4200 - Connection Keeps Dropping
Feb 4, 2011I just got an E4200 and have a SBG6580 cable modem. I cant seem to set this up properly and my connection keeps dropping. What is the proper set up ? I would like to configure it so the cable modem handles the DNS and the E4200 handles the wireless.
View 4 Replies View RelatedReset Motorola SBG901 Router - Now Can't Access Login Page
Feb 21, 2012I have a Motorola SBG901 router. Typing ipconfig showed that 172.18.8.1 is the Default Gateway and this is the URL I always used to access the router login page.
I reset the router today by holding the reset button. Now typing the URL 172.18.8.1 does not work. The router user guide says to go to 192.168.0.1. I have tried this but it also does not work. For both I just get the "problem loading page" in Firefox.
The Internet works fine both with an ethernet connection and wirelessly. My only issue is that I cannot access the Motorola router login page. I could access it fine this morning before I reset the router.
Linksys Wireless Router :: WRT54G / Unable To Access Gateway
Jul 18, 2006I'm unable to access my linksys wireless g broadband router (WRT54G)'s access gateway. (192.168.1.1)The gateway page doesn't load, at all. It doesn't ask for the user or password at all. On any of my internet browsers (firefox, and internet explorer)Anyway of fixing this would be appropriate.
View 2 Replies View RelatedCisco Wireless :: 1262 - Acting As Client To Another AP?
Sep 8, 2012Our scenario requires some customization in Wireless network. We have moving Forklift machines fitted with network devices. The network device in forklift acts as a client. But it doesn't have a wireless adapter and no provisions to add a wireless adapter. There is one ethernet port.
So we have a plan to attach one AP(1262) to each forklift. this AP needs to talk to the AP whcih is connected to Wired network. The network deivce in the forklift need to talk to the root AP(1262) through the AP directly connected to it over Ethernet.
Linksys Wireless Router :: E1200 Do Not Have Internet Access As Default Gateway
Nov 11, 2011I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Access Point :: WRT54G - Unable To Find Access Point In Home Network
Aug 29, 2009I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
Linksys Wireless Router :: E1500 DHCP Gateway Address Always Defaults To Access
Apr 28, 2012I have a ADSL Modem with built in router that the E1500 is connected to via Ethernet.If I choose "Automatic Configuration" for the internet connection setting on the E1500 I can enable DHCP on the E1500 but the gateway it gives to clients is always that of itself (192.168.1.1). The gateway it should be is that of the ADSL Modem (192.168. 1. 254).If I choose "Bridge Mode" I can't even enable DHCP.Is there a way I can use the DHCP server?
View 1 Replies View RelatedWireless :: Access Point With Router?
May 2, 2012I have TP Link Wireless Router i attached TP Link access with it. The problem is am unable to see the attached Access Point in the Router, so that i could see the other users who are connected with that AP. Internet through that access point is available for all the users.
View 3 Replies View Related