Linksys Wireless Router :: E1200 Not Responding - Internet Gets Off
Oct 26, 2012
I have E1200 wireless router and it was working nicely for the whole last year with 2 mac laptops hooked up on it. About 2 months ago there were 1 mac,1 win laptop and a network printer. And again, it was working just fine at the beginning. I'm not sure when exactly it happened first, but now after working couple of hours internet gets off and router stops responding. If I try to reconnect to it from my laptop I just see an error message saying something about "Connection timeout". Also I don't know does it have something to do with the network printer, btw it's connected to the router via ethernet cable not wireless. Anyway, the only solution I've found so far is power off the router for a couple of secs and power it on again, which is obviously not a solution at all, it's annoying and not practical. The time it works fine before it dies is also not fixed, it might be even 10 hrs of working and sometimes only 1-2 hrs. My other suspicion is firmware. I upgraded it almost at the same time when new laptop and printer showed up. Maybe I have to downgrade it, but I couldn't find older version of it. It was HW v. 1, SW v.1.0.00, and now it's HW v.1, SW v.1.0.03.
View 1 Replies
ADVERTISEMENT
Jan 17, 2013
I have a linksys e1200 wireless router and the internet port does work. Is there a way to make one of the lan ports the internet ports?
View 1 Replies
View Related
Jan 3, 2013
I wish to have a home network using the E1200 without an internet connection. I have a netbook (Lenovo S100) and a Samsung Galaxy Note II. I want to be able to have both connected to the router so I can interface the two devices using a program such as Teamviewer.
View 1 Replies
View Related
Oct 14, 2011
I had recently purchased the E1200 router. For some reason, my internet keeps going in and out of service. I will be playing an online game but get disconnected from the server every 6-8 seconds. I tested if it could be my internet provider, but when I connect via Ethernet cord to my modem, it works great. If I run the Ethernet through my router or try wireless connections, it tends to go in and out. It only seems to do this some of the times.
View 1 Replies
View Related
Aug 12, 2012
I just bough Linksys E1200, downloaded setup software, ran it, all setup went fine, no errors, but at the end I got the screen saying that can establish internet connection.The steps are totally simple. Did exactly as instructed.'Modem, connected to a PC directly give internet no problem.Modem, connected to the router, and router connected to PC - no internet.And... It's all wired at this moment, all connected with network cable.
View 9 Replies
View Related
Jan 16, 2013
I received the Linksys E1200 today and I installed it according to the instructions but at the end of the installation it showed the message "No internet connection." I restarted the router + modem but that didn't work at all
View 4 Replies
View Related
Sep 5, 2012
I have E1200 router and a Motorola cable modem. I can access the router and internet with a wired connection but when I unplug the ethernet cable I no longer have internet access. I can connect to the router. I have another computer and xbox that are running wireless with full internet access.no problem.
View 3 Replies
View Related
Apr 6, 2012
I can connect to the wireless network, but cannot connect to the internet. The guest can connect but not the main user.E1200..Win7SP1.
View 1 Replies
View Related
May 14, 2012
Linksys E1200. I cannot connect to the Internet through my primary connection, but I can still connect through the guest connection. I think I know what happened, but I don’t know how to fix it. A connect / disconnect key on my keyboard is located right next to the mute sound key. I wanted to mute my sound, and when it didn’t mute I pressed the key a couple more times before I realized I was pressing the wrong key. So I’m guessing I probably messed up some settings. But I don’t know if on the computer, router, or both. Per the documentation I thought I might be able to fix it with Cisco Connect, but it wasn’t installed on my computer. There were only 3 Cisco modules installed.. EAP-FAST module, LEAP module, and PEAP module. I managed to find Cisco Connect on the website and downloaded it, but still couldn’t fix the problem.
View 2 Replies
View Related
Sep 10, 2011
Okay so my friend recently bought a Linksys E1200 Wireless-N Router. We set it up the other day and it all appears to be functioning just fine. The only problem is when we log into her wifi it says "No Internet Access". I'm moderately okay when it comes to computers but not expert and I'm horrible at the whole wifi router thing. Through my laptop I've done a Windows Network Diagnostic to see what was wrong and it says that my "computer is correctly configured but the device or resource (DNS server) is not responding."
View 8 Replies
View Related
Sep 15, 2012
I just upgraded my router from an old wireless54G to an E1200.The wireless device I have on my Sony Viao PCG GRT-240G laptop is LAN-Express AS IEEE 802.11g miniPCI Adapter
-Initially I couldn't connect at all with this machine (however the other two newer laptops could) so I contacted the Linksys tech and he advised I should upgrade my laptop driver
-After much research about this I found a common fix was to upgraded drivers from the 2004 sony driver to atheros_wifi_9.2.0.480 drivers.
-After I did the upgrade I can connect to the router on the guest account and use the internet
However, on the Main account I can connect to the router but I have no internet connectionGoogle chrome gives error belowThe server at [url]... can't be found, because the DNS lookup failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.How can I use one part of the network but not the other part? Shouldn't both the guest & main accounts use DNS lookup?
View 2 Replies
View Related
May 22, 2012
why I am having a slow connection? Before purchasing Linksys E1200 wireless router, my internet speed was perfectly normal with Netgear wireless router. Everything ran smoothly but once I installed Linksys, it began to have slow connection. It also has drop connection sometimes. How do I fix my connection speed and the drop connection?
View 5 Replies
View Related
Dec 11, 2011
We've moved apartments in the same building that provides LAN internet. But in the new apartment the internet is working fine when I plug it in the computer directly, but when I plug it in the router (E1200) it says there's no Internet connection. No WIRED internet and No WIRELESS Internet. I don't get it. The same router I took it back to our original apartment and works fine when I hook up the same ethernet cable to the LAN.
View 3 Replies
View Related
Dec 2, 2012
I purchased the E1200 Linksys Wireless Router on 11/26/12. The router worked fine until today. Without reason, the router stopped reading the internet cable/the port on the router stopped detecting the signal from the cable connected to the modem. I can plug the cable from the modem directly into a laptop and the laptop picks up the signal (using it to write this). I swapped out several DSL cables to confirm it wasn't a cable issue and it does not make a difference. I tried rebooting the router, resetting the router, and yet nothing works.
View 4 Replies
View Related
Nov 24, 2012
I would like to wirelessly connect my printer through the new router without internet. The setup CD won't allow me to install without an internet connection.
View 2 Replies
View Related
Jan 14, 2013
I basically plugged it into my Verizon Fios router and downloaded the Cisco Connect application (since I have a macbook air which has no CD drive)
It sets up fine, I change my router name.... BUT at the end it says there is an issue of some sort. The Cisco Connect application reloads saying "repairing connection" but then does not repair it.
Not sure where to go from here. I also logged in to 192.168.1.1 but of course I do not know where to go from here. I also reset the router trying to start from new, but no dice.
View 9 Replies
View Related
Jan 18, 2013
Just set upa new e1200 on my brand new primary PC - connects flawlessly. One other PC in the house and an iphone also connect on the network to the internet with no issues. The problem: My laptop connects to the secure network without prompting for a password,but then does not connect to the internet at all. This same laptop easily connects to the internet via the network as a guest, just as it should. Tried using Easkey, but same result: laptop connects OK to the secure network without a password prompt, but then does not connect to the net.
View 5 Replies
View Related
Sep 19, 2011
I have a question about the function of an E1200 relative to a WRT54G. We currently have the 54G plugged into our LAN, the Ethernet cable plugged into one of the Ethernet ports, not the Internet port, on the back. It is giving wireless clients IP addresses according to our main LAN DHCP, as if they were hard-wired which is correct. Bad thing is, I have no idea what IP address is/was assigned to the 54G itself as it was not logged when done, way before my time. I cannot log into it and take a look at its settings and attempt to mimic what is going on in there on something like an E1200.
Therin lies my next questions. What could be occurring on the 54G that is enabling it to dish out like a WAP and does the E1200 support WAP function? If not, which models do that can be added to the 54G?
View 8 Replies
View Related
Mar 28, 2013
I have a Cisco E1200, I am wanting it to connect to the net using Etisalat ISP. The computer will talk to the router and all the settings look correct but it will not connect to the internet.The router did a software upgrade that it deemed successful.
View 9 Replies
View Related
Jul 31, 2012
I recently was able to obtain my son's Nintendo 3DS from him and now I can't figure out how to get on the internet browser with it!When I open up the internet on his 3DS and when I try to access anything it says communication error even though I have a full signal. It also says that the "error code is: 012-1018 Connection to proxy server failed. Please check that your proxy server settings are correct." I have went in and tried to change the proxy server settings and if I do I lose the internet connection despite the fact that the correct information is set in place. I even tried to reset the router (as my son did before) but I can't access it, even though he was able to!! I have done research on the Nintendo web site and everything that it says to do I have done and it shows that I have a full signal but after that no luck.
View 2 Replies
View Related
Dec 18, 2012
I just bought a Cisco e1200 router... and the wireless connection is way too slow, when navigating through the web, but when using speed test, the connection seems fine, but still it even takes more than usual to open simple pages, lets say Google... i usually watch streams and now that i cannot do... when i connect directly i can do everything as usual...as i have read, i change channels, but still no improvement, i have the latest firmware, on my range there are only 2 more available connections... i even tried disabling/enabling the WMM... We all know that having extremely slow internet must be the real "Mayan apocalypse"
View 2 Replies
View Related
Sep 12, 2012
I just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04.My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
View 4 Replies
View Related
Apr 15, 2012
I recently purchased an E1200 to replace a broken router. I have had good experiences with this model in the past which is why I bought it. However this has not been so pleasant. For some reason the internet connection over wifi is INCREDIBLY slow. I don't know why. It is fast when connected via ethernet to the router. I changed the MTU on the router to 1400, I set the wireless width to 20MHz and the channel to 11. I set security to WPA2. And yet it is still very very slow. It's not a matter of how many users are on the network; I live in a house with five other people and it's slow regardless of whether everybody's home or nobody is home. It's like this on Macs, PCs, phones and even the Xbox 360. I just did a speed test. Wired was about 14MBps down, wireless was around .7MBps down. I simply cannot comprehend this discrepancy. The old router was very unreliable in terms of connectivity but at least it was always fast. And my laptop is fast at my mom's house where she has an E1200. I use a MacBook Pro from 2009 but like I said,this seems to be affecting everybody in the house regardless of hardware.The modem is a Ubee modem from Comcast. I'd upgrade it to a SURFBoard but my landlord controls all the utilities and I'd rather not have to explain to him how to call Comcast and tell them to register the modem's serial number to the account or whatever.
View 2 Replies
View Related
Jul 24, 2012
We have a Linksys E1200 modem and I have been having problems with keeping my son from using the wireless interenet. I did change the password and that worked for about 24 hours and then he was able to get onto it again. He has a nintendo dsi and he is smart enough to figure out how to dismantle any parental controls on his gaming device. I think that he resets the modem in order to get back onto the internet in order to use his gaming device. Someone told me that you can register each item individually in order to keep kids from using it but I have no idea as to how this works. We have two iphones, a lap top, and two tablets.
View 7 Replies
View Related
Jun 22, 2012
I installed an E1200 wireless router yesterday and everything worked fine. However, I happened to turn off the modem overnight and now my computer indicates (under Wireless Network Connection) that I'm connected, but above (under Currently Connected To) it says that I have No Internet Access. I tried turning off the modem, router and computer and turning them on again in that order, but that didn't work. Do I need to do the set-up again ?
View 5 Replies
View Related
Feb 27, 2012
I am trying to setup my Internet connection on my linksys E1200 router using static IP settings below -I am getting following error when trying to do this. These are the IP settings provided to me and are configured on my laptop to connect to my ISP as well.
View 6 Replies
View Related
Nov 11, 2011
I have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies
View Related
Jan 3, 2012
I am trying to set up my E1200 router to Frontier FIOS internet. I went thru the setup and it failed to connect to the internet. What settings do I need? Frontier says that it should find the connection automatically.
View 1 Replies
View Related
Oct 2, 2011
Why does my E1200 forget my Parental Control Password? This happens almost weekly and I have to use the "forgot password" option. It asks my security question, I answer it and set the new password to the same password it keeps forgetting. Why does this happen? Also, is there anyway to have total 24hr control on the Block Internet Access?
View 4 Replies
View Related
Sep 23, 2011
Use wireless router and can connect to internet on laptop. When trying with PC (windows xp software), I can't connect. Ran diagnostic, result: Your computer appears to be correctly configured, but the device or resource (web proxy) is not responding.
View 1 Replies
View Related
Jul 24, 2012
I have a Linksys E1200 wireless router and I am having problems connecting to the internet. I can connect when plugged in to the cable modem directly. I can connect to the wireless network, but there is no internet connection. I ran ipconfig release and renew. I think it may be a DNS problem, but I'm not sure.
View 7 Replies
View Related
Sep 14, 2012
MY RE-1000 is up and working at 192.168.1.141. But I get nothing back when I put this address into IE.
View 3 Replies
View Related
Feb 23, 2012
I have a wireless router and I'm trying to user UPnP feature. of course it is enble in the router.
It's working one and after it stop working, looks like the router is not responding anymore. If I got on the web interface of the router, I loging, on the first web page I press save changes, even if I didn't change anything, the UPnP feature work again.
Looks like a timeout occure or something like that. Is there a way to wake up the router without having to go on the web interface? Why it's stop working?
Firmware Version: v4.30.15
View 1 Replies
View Related
