I have E1200 router and a Motorola cable modem. I can access the router and internet with a wired connection but when I unplug the ethernet cable I no longer have internet access. I can connect to the router. I have another computer and xbox that are running wireless with full internet access.no problem.
View 3 RepliesOkay so my friend recently bought a Linksys E1200 Wireless-N Router. We set it up the other day and it all appears to be functioning just fine. The only problem is when we log into her wifi it says "No Internet Access". I'm moderately okay when it comes to computers but not expert and I'm horrible at the whole wifi router thing. Through my laptop I've done a Windows Network Diagnostic to see what was wrong and it says that my "computer is correctly configured but the device or resource (DNS server) is not responding."
View 8 Replies View RelatedI just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04.My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
I installed an E1200 wireless router yesterday and everything worked fine. However, I happened to turn off the modem overnight and now my computer indicates (under Wireless Network Connection) that I'm connected, but above (under Currently Connected To) it says that I have No Internet Access. I tried turning off the modem, router and computer and turning them on again in that order, but that didn't work. Do I need to do the set-up again ?
View 5 Replies View RelatedI have my E1200 connected to my Netgear FVS318 router (which is a wired router) and the Netgear is connected to the internet.When a wireless client attempts to connect to the internet after automatically receiving an IP from the E1200, they do not have internet access as the default gateway that gets assigned is the IP of the E1200 192.168.2.100, which is not correct. It should be assigned 192.168.2.1, which is the IP of the Netgear router. Thefore, I have to manually set their IP addresses to use 192.168.2.1. How do you configure the E1200 to assign the correct Default Gateway IP to wireless clients who want to use DHCP?
View 4 Replies View RelatedWhy does my E1200 forget my Parental Control Password? This happens almost weekly and I have to use the "forgot password" option. It asks my security question, I answer it and set the new password to the same password it keeps forgetting. Why does this happen? Also, is there anyway to have total 24hr control on the Block Internet Access?
View 4 Replies View RelatedWhat happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
View 2 Replies View RelatedIs it possible to use an E1200 as an access point? I am connecting it to an SE2500..
View 1 Replies View RelatedI'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....
View 6 Replies View RelatedI had a E1200, I read the articles from the support about the routers, I think the "access Restrictions" has more flexible to setup on for the parental control, after chated to cisco support person online, I was told that the E1200 v2 has this "access restrictions" function, and I wan convinced to purchase from them. I did. I got the E1200 v2 recently, however, after I installed the CD and found there is no "access restrictions" tab, instead the "access policy" is still there. by the way the firmware is 2.0.02 now. How to get the "access restrictions" from setup? I've chatted with cisco support person twice again, but nobody can fix the problem, one suggested to restart and reinstall the CD. I uninstalled the software, restarted the computer and reinstalled the CD. same problem, no tab of "access restrictions".
View 6 Replies View RelatedI have a Linksys E1200 router.My problem is I have installed a camera system that allows remote viewing.I cannot access the system through the E1200 I am not very knowledgeable in net working.What do I need to do to access the DVR from a remote computer?
View 1 Replies View RelatedTrying all week to get my E1200 setup as an Access Point with my AT&T U-Verse 2WIRE Modem. [code] It just never seems to work correctly. It will connect for a second or 2 and then jam up. My ultimate scenario would be to have the E1200 just act as a wireless access point and have the 2WIRE do the rest: firewall, DCHP, etc.
View 9 Replies View RelatedI have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not.
View 1 Replies View RelatedI have a linksys e1200 wireless router and the internet port does work. Is there a way to make one of the lan ports the internet ports?
View 1 Replies View RelatedI wish to have a home network using the E1200 without an internet connection. I have a netbook (Lenovo S100) and a Samsung Galaxy Note II. I want to be able to have both connected to the router so I can interface the two devices using a program such as Teamviewer.
View 1 Replies View RelatedI had recently purchased the E1200 router. For some reason, my internet keeps going in and out of service. I will be playing an online game but get disconnected from the server every 6-8 seconds. I tested if it could be my internet provider, but when I connect via Ethernet cord to my modem, it works great. If I run the Ethernet through my router or try wireless connections, it tends to go in and out. It only seems to do this some of the times.
View 1 Replies View RelatedI have E1200 wireless router and it was working nicely for the whole last year with 2 mac laptops hooked up on it. About 2 months ago there were 1 mac,1 win laptop and a network printer. And again, it was working just fine at the beginning. I'm not sure when exactly it happened first, but now after working couple of hours internet gets off and router stops responding. If I try to reconnect to it from my laptop I just see an error message saying something about "Connection timeout". Also I don't know does it have something to do with the network printer, btw it's connected to the router via ethernet cable not wireless. Anyway, the only solution I've found so far is power off the router for a couple of secs and power it on again, which is obviously not a solution at all, it's annoying and not practical. The time it works fine before it dies is also not fixed, it might be even 10 hrs of working and sometimes only 1-2 hrs. My other suspicion is firmware. I upgraded it almost at the same time when new laptop and printer showed up. Maybe I have to downgrade it, but I couldn't find older version of it. It was HW v. 1, SW v.1.0.00, and now it's HW v.1, SW v.1.0.03.
View 1 Replies View RelatedI just bough Linksys E1200, downloaded setup software, ran it, all setup went fine, no errors, but at the end I got the screen saying that can establish internet connection.The steps are totally simple. Did exactly as instructed.'Modem, connected to a PC directly give internet no problem.Modem, connected to the router, and router connected to PC - no internet.And... It's all wired at this moment, all connected with network cable.
View 9 Replies View RelatedI received the Linksys E1200 today and I installed it according to the instructions but at the end of the installation it showed the message "No internet connection." I restarted the router + modem but that didn't work at all
View 4 Replies View RelatedI can connect to the wireless network, but cannot connect to the internet. The guest can connect but not the main user.E1200..Win7SP1.
View 1 Replies View RelatedLinksys E1200. I cannot connect to the Internet through my primary connection, but I can still connect through the guest connection. I think I know what happened, but I don’t know how to fix it. A connect / disconnect key on my keyboard is located right next to the mute sound key. I wanted to mute my sound, and when it didn’t mute I pressed the key a couple more times before I realized I was pressing the wrong key. So I’m guessing I probably messed up some settings. But I don’t know if on the computer, router, or both. Per the documentation I thought I might be able to fix it with Cisco Connect, but it wasn’t installed on my computer. There were only 3 Cisco modules installed.. EAP-FAST module, LEAP module, and PEAP module. I managed to find Cisco Connect on the website and downloaded it, but still couldn’t fix the problem.
View 2 Replies View RelatedI want access the my E1200 website in order to implement new username and password to secure the network.
View 1 Replies View RelatedI have a new E1200 router. I VPN from home to my work computer just fine. since I can remotely access the router from work...what setup section of the router would I need to utilize to go backwards and access my home PC thru remote desktop? NAT? if so what are the instructions to do so.
View 1 Replies View RelatedI have a Cisco 880 (supplied by my company and as such I have little access to the control panel). I have a Linksys (Cisco) E1200 to use as an access point. Cisco setup (love it!) but the simple setup gives the E1200 an ip range starting at 192.168.1.1 while the Cisco 880 range is 192.168.185.113. I need to have all connections in the same ip rage (192.168.185.xxx) for remote monitoring. What is the best way to accomplish this? Bridge mode (I don't need Guest Mode which I read is not possible in bridge mode)? Disable DHCP on the E1200?
View 1 Replies View RelatedI just upgraded my router from an old wireless54G to an E1200.The wireless device I have on my Sony Viao PCG GRT-240G laptop is LAN-Express AS IEEE 802.11g miniPCI Adapter
-Initially I couldn't connect at all with this machine (however the other two newer laptops could) so I contacted the Linksys tech and he advised I should upgrade my laptop driver
-After much research about this I found a common fix was to upgraded drivers from the 2004 sony driver to atheros_wifi_9.2.0.480 drivers.
-After I did the upgrade I can connect to the router on the guest account and use the internet
However, on the Main account I can connect to the router but I have no internet connectionGoogle chrome gives error belowThe server at [url]... can't be found, because the DNS lookup failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.How can I use one part of the network but not the other part? Shouldn't both the guest & main accounts use DNS lookup?
why I am having a slow connection? Before purchasing Linksys E1200 wireless router, my internet speed was perfectly normal with Netgear wireless router. Everything ran smoothly but once I installed Linksys, it began to have slow connection. It also has drop connection sometimes. How do I fix my connection speed and the drop connection?
View 5 Replies View RelatedWe've moved apartments in the same building that provides LAN internet. But in the new apartment the internet is working fine when I plug it in the computer directly, but when I plug it in the router (E1200) it says there's no Internet connection. No WIRED internet and No WIRELESS Internet. I don't get it. The same router I took it back to our original apartment and works fine when I hook up the same ethernet cable to the LAN.
View 3 Replies View RelatedI purchased the E1200 Linksys Wireless Router on 11/26/12. The router worked fine until today. Without reason, the router stopped reading the internet cable/the port on the router stopped detecting the signal from the cable connected to the modem. I can plug the cable from the modem directly into a laptop and the laptop picks up the signal (using it to write this). I swapped out several DSL cables to confirm it wasn't a cable issue and it does not make a difference. I tried rebooting the router, resetting the router, and yet nothing works.
View 4 Replies View RelatedI would like to wirelessly connect my printer through the new router without internet. The setup CD won't allow me to install without an internet connection.
View 2 Replies View RelatedI basically plugged it into my Verizon Fios router and downloaded the Cisco Connect application (since I have a macbook air which has no CD drive)
It sets up fine, I change my router name.... BUT at the end it says there is an issue of some sort. The Cisco Connect application reloads saying "repairing connection" but then does not repair it.
Not sure where to go from here. I also logged in to 192.168.1.1 but of course I do not know where to go from here. I also reset the router trying to start from new, but no dice.
Just set upa new e1200 on my brand new primary PC - connects flawlessly. One other PC in the house and an iphone also connect on the network to the internet with no issues. The problem: My laptop connects to the secure network without prompting for a password,but then does not connect to the internet at all. This same laptop easily connects to the internet via the network as a guest, just as it should. Tried using Easkey, but same result: laptop connects OK to the secure network without a password prompt, but then does not connect to the net.
View 5 Replies View RelatedI have a question about the function of an E1200 relative to a WRT54G. We currently have the 54G plugged into our LAN, the Ethernet cable plugged into one of the Ethernet ports, not the Internet port, on the back. It is giving wireless clients IP addresses according to our main LAN DHCP, as if they were hard-wired which is correct. Bad thing is, I have no idea what IP address is/was assigned to the 54G itself as it was not logged when done, way before my time. I cannot log into it and take a look at its settings and attempt to mimic what is going on in there on something like an E1200.
Therin lies my next questions. What could be occurring on the 54G that is enabling it to dish out like a WAP and does the E1200 support WAP function? If not, which models do that can be added to the 54G?
I have a Cisco E1200, I am wanting it to connect to the net using Etisalat ISP. The computer will talk to the router and all the settings look correct but it will not connect to the internet.The router did a software upgrade that it deemed successful.
View 9 Replies View Related