Linksys Wireless Router :: E2500 - Cannot Access It
Dec 27, 2011
I have bought and installed an E2500 router 4 days ago. Installation of router and network using Cisco Connect was easy and without problems. However, after 4 days of usage, not changing anything in the network nor running Cisco Connect or accessing the web interface, I tried to start Cisco Connect and got the message "Cannot access your router".Internet is running, router is accessible via 192.168.1.1 in a browser window, Cisco Connect also works fine on my laptop.The only solution I found on this forum is: reset your router and reinstall Cisco Connect.and then every 4 days resetting my router and reinstalling the software?
View 4 Replies
ADVERTISEMENT
Apr 21, 2012
I bought a new e2500 and it is working fine, all but port forwarding. This is not even close to my first router and I am advanced when it comes to setting these up. I have tried for days to get port 80 to open up and it refuses. Now I do notice that when you access the router setup through a web interface, it uses port 80. I have forwarded port 80 to the ip address of the device, put in a reservation in DHCP with MAC address, etc. etc. and still nothing. Heck, I have even turned that specific device IP into a DMZ, and it STILL will not work.For the record, I had an e2000 set up the exact same way and it worked just fine and I was able to access port 80.
View 6 Replies
View Related
May 17, 2011
I have an E2500 running as a router/DHCP server. For reasons beyond the scope of this question, I am replacing the router and DHCP functions with a SonicWALL device. I would like to continue to use the E2500 as a wireless access point only, providing WiFi connection to the SonicWALL. How do I set up the E2500 for this purpose. I assume I switch off the DHCP server and NAT within the device. Is there a dedicated "access point" mode?
View 9 Replies
View Related
Jan 22, 2012
Here is my setup.Using all MAC OSX I have AT&T DSL ISP connected to a (ISP provided) Speedstream 5100 Modem.I just purchased a Cisco Linksys 5200 N Router and I cannot access the internet. I followed the set-up instructions to the T but to no avail. I cannot find anything online about these two devices being incompatable. Do I purchase a new modem? If so how can I be sure it's compatible with the router?
View 1 Replies
View Related
Mar 1, 2013
I bought the router E2500 and I followed the steps for its configuration. It so happens that most of the time I turn on my router, it does not connect to microcomputer, because it loses the internet settings, requiring that I turn the CISCONNECT and after that, I have to turn off the microcomputer, wait for 2/3 minutes and then reconnect, for only then will be able to surf the internet. I notice that many times even I doing all this procedure the router does not give access to the internet. What should I do?
View 1 Replies
View Related
Oct 31, 2012
E2500 given to me cannot access password to setup
View 1 Replies
View Related
May 28, 2012
I have an old WRT54G and the access restrictions really don't work. it's sloppy and ineffective.
i'm thinking about upgrading... perhaps to the E2500. Do the access restrictions now work properly? Am I able to allow access to a specific site only during certain times?
For instance, am I able to provide access to [URL] only during 6:00pm-9:00pm and block it otherwise?
View 6 Replies
View Related
Dec 13, 2012
I have an existing home network with a D-link wireless router, IP 192.168.0.1. In the past, I set up another of the same model Dlink router as a WAP to extend my network by simply disabling DHCP and setting its IP to 192.168.0.100. Used the same SSID and passwords, worked flawlessly. Now, my WAP-router has failed and I purchased a LINKSYS E2500 to replace it in that function. I'm trying to configure it the same way but am having problems.The Linksys' IP is 192.168.1.1 by default. I hooked its LAN port to my laptop and accessed the setup page at 192.168.1.1. I changed the router IP to 192.168.0.200 and disabled DHCP. I saved settings, the router reset, and since, I am unable to re-connect to that router setup screen at either 192.168.0.200 OR the default 192.168.1.1. I reset the router to default and tried this multiple times but could never get back to the setup page (didn't even configure any wireless settings yet) after I made the IP change and disabled DHCP. With my previous router, this worked easily and flawlessly.
1. What am I doing wrong (ok, other than using Dlink components)?
2. Should these two different brand components work ok together llike this or is that a problem?
3. Why should unticking DHCP and/or changing the IP address as described make the device unreachable?
View 2 Replies
View Related
Oct 13, 2012
I just purchased an E2500 wireless router. I put the Cisco Connect setup disc in and it could not find my router. With excellent Tech Support, I got it to work. I still do not have any Cisco Connect software on my PC to set passwords or preferences. If I try to run the disc again, it gives me a system critical error and shuts down my computer. How can I get software to access my router settings?
View 1 Replies
View Related
Mar 2, 2013
Since installing the E2500, I can no longer access YouTube videos on my wireless devices. Is this a setting that needs to be changed?
View 1 Replies
View Related
Nov 1, 2011
I did not use the CD to set up, and instead set this router up manually. We are using this router right now as a hotspot only.. and all is good. I can see both new networks and the WIFI laptops are talking no problem. Only issue I have is that guest access is not working - by that I mean it can't get out on the internet. I can see it as available and connect to it. Guest access and SSID broadcast are both enabled obviously.
View 8 Replies
View Related
Dec 29, 2012
using a Linksys E2500. I have a Ubuntu "server" set up which i can access on my LAN through VNC Viewer (windows machines) no problem. I can even access it through the external IP address on a machine inside the LAN (both internal address and external address work from inside the LAN). I set up port forwarding (per portforward.com) but i still can not access my machine from outside the LAN. It has a static IP as well btw.
View 2 Replies
View Related
Jul 24, 2012
Is it possible with the E2500 (or some other device) to rebroadcast a wireless signal?Here's the situation, I live on a boat, I want to connect my laptop to a local wireless signal (which I pay for). I then want to connect my E2500 to the laptop via the "Internet" port on the E2500. This doesn't work? This would allow all my wireless devices to stay connected to a single connection point. When I move the boat and change the wireless connection, I only have to do it once for a single connection. Is there some way to achieve this?
View 1 Replies
View Related
Dec 19, 2012
I just bought this Cisco E2500 router last night. I was able to set new pass phrase and name (SSID). I then proceeded to add wireless computers to the router-no problem. had 1 computer I couldnt set up because the person was sleeping. So this morning I go to set up their computer, and found the name (SSID) on the available networks. I clicked on it, and it connected right away WITHOUT ASKING FOR THE PASSPHRASE!!!!! NO ONE put the pass phrase in this computer before. I checked the connection-and sure enough, there was the passphrase right there on this computer! So HOW did this computer, that I hadnt ever tried to connect to this new network before- suddenly get the passphrase as well? if anyone in this neighborhood can just connect to my network and automatically get the passphrase like that-then I need to take this back and get a refund!! That isnt secure at all!
View 1 Replies
View Related
May 1, 2012
I am running a wired and wireless home network..using a G 2.4 router and access point. I purchased an Linksys E2500 N 5Ghz wiresless router can I still effectively use my Linksys G 2.4 g access point? Will I still have to get a linksys N 5Ghz access point to properly obtain the most speed and security?
I use the wireless with a cable service and use wireless access only for the cell phones via WiFi.I rarely use the desktops on the home network, I want to increase the speed for the cell phone via Wi-fi, Currently speedtest results were 4.80 for downloads and 2.0 for uploads. I have not much use for uploading except for sending photos via wi-fi.
View 1 Replies
View Related
Apr 16, 2013
I will be working from home half the time and am trying to get set up. So here it goes:
Took PC #1 home and hooked everything up. Could access Internet.Had to bring PC #2 home because #1 didn’t have the programs I needed.Hooked #2 up, no internet access.Tried different network cable – no access.Tried different router port – no access. (router port light doesn’t illuminate, neither does port on PC)My personal PC that uses the same router has internet access.Hooked #1 back up as a test – could access internet.Hooked up #2 again, did a Run, cmd, ipconfig and got “media disconnected”I brought #2 back in for a PC tech to look at. He hooked it up in his office, had internet access.Took it back home and hooked everything up.The port lights illuminated on startup; but after it got to the desktop, lights are off.Tried ipconfig again, "media disconnected”. IP address doesn’t display.
All the while I have internet access on my own PC, plus when I hook up #1 to the same port using the same cable, I have internet access, which led me to believe it's something wrong with PC #2.Tech is saying it’s a problem with my router (Cisco E2500), which I restarted too.
View 4 Replies
View Related
May 2, 2012
I'd like to use an E2500 as a wireless access point in my network. My computer is connected to the office network through a Netgear 5 port desktop switch. Would it be easier for me to configure the E2500 from the switch? If so, do I just plug it in there and access it via the 192.168.1.1 IP address to set it up? And lastly, what should disable (DHCP) or setup in the router so the internet functions through it?
View 8 Replies
View Related
Dec 20, 2011
I got 5 E2500 routers and the main one has setup to IP address 192.168.1.254 and the rest APs are programmed into the bridge mode with the IP address 192.168.1.245 through 248. The secured wireless network works fine when I roaming between these APs but the only AP that I can get internet access for guest wireless network is the main (192.168.1.254) router; for every other APs, I will get the guest log on screen (prompt for guest access password) and no internet access after I type in the correct access password. Does the E2500 support multiple APs guest or it requires a special way to configure it?
View 5 Replies
View Related
Nov 14, 2012
Is there any way to use the e2500 without having hard wired internet access. I would like to use with my wii fii hot spot so that I could use my old printers that are not wireless enbled
View 1 Replies
View Related
Oct 16, 2012
I have AT&T Uverse which provides Internet for my home. The wireless capability of this router is pretty bad, I don't get good/reliable wireless reception upstairs in my office. The solution was to buy a Cisco E2500 and add it as an access point upstairs.
I have the E2500 LAN port connected to the LAN port of my uverse router downstairs. DHCP is turned off on the E2500. I have my office PC wired into the E2500. The home PC works fine, its getting DHCP from the uverse router downstairs and connects and good speeds. The problem comes with my wireless devices trying to connect to the E2500.
I should mention that yesterday when i bought this, all worked fine. This morning when I came into my office none of the wireless devices would connect to the E2500 at all. But as soon as I remove the cable that connects the E2500 to the uverse router downstairs they will connect via wireless but of course not get an IP address since that is disabled.
I have factory reset the E2500 and uverse router several times and am getting no where. what could be causing the wireless devices to not connect at all?
View 8 Replies
View Related
Jul 19, 2012
I am using an E2500 as an access point, which is working fine. I have an Ethernet cable on one of the LAN ports of the E2500 connected to a LAN port on my gateway router. The LAN address of the E2500 is 192.168.7.3 and the LAN address of the gateway router is 192.168.7.1. Clients on the E2500 wireless network have no problems getting to the Internet through the gateway router. Clients on the E2500 wireless network can reach the E2500 local management port at 192.168.7.3 on port 80. On the gateway router I am forwarding WAN port 8083 to LAN address 192.168.7.3 at port 80. But I cannot access the E2500 local management interface via the gateway router. The E2500 should see the request as from 192.168.3.1 due to NAT in the gateway router, right? I can reach any of my actual access points this way, just not a router being used as an access point. Security/design limitation of the router?
View 2 Replies
View Related
Jan 18, 2012
I am looking form accesspoint for home network. I do not need router and usb functionality, I have this already in my linux server. I need only wifi accesspoint with 2 bands and 300Mbps bandwith. Is there a big difference between E4200 or E3200 or E2500? I know that E4200 supports 450Mbps, but I am not planning to buy new devices which could go faster than 300Mbps. Beside of technical parameters in technical specyfication is there a difference in wifi bandwith or tranmission between wifi and cable network?
View 9 Replies
View Related
Nov 11, 2012
is it possible to eliminate the the guest login screen from being displayed/required to acess router from an added device(like a smart tv with a web browser)?router is an e2500,approx.
View 4 Replies
View Related
Oct 20, 2012
Just installed Linksys E2500 router connected to my Desktop and Cable Modem and access the internet fine. My kindle accesses it and the internet fine. My laptop running Vista connects nicely but only has local access. I find the network and connection area where it sees a network with local only access. I have no clue how to go about changing that. I have the correct password because my Kindle asked me. My laptop does not ask for the password.
View 3 Replies
View Related
Jan 4, 2012
I have a Cisco Linksys E2500 modem and I cannot access Zoneminder which is essentially a Linux Security video DVR software package. It is running on a Ubuntu Linux server.
I have HTTP port 80 forwarded to the the static IP address of the Ubuntu server but I repeatedly get a error indicating that the connection timed out whenever I try to access Zoneminder remotely as in remotely accessing it from a coffee shop.
I have absolutely no problem accessing Zoneminder when I on my home local LAN.
I can access other software from remote locations on port 4369 with a TCP preferred protocol setting. That is, port 4369 is forwarded to another Windows workstation with an assigned static IP address. Absolutely no problems with port forwarding of 4369.
Also, I've tested port 80 on the YouGetSignal website which is used for testing port forwarding. The website indicates that port 80 is closed. But when I test port 4369, the website reports that the port is open. Zoneminder which uses port 80 is fully operational when I test port 80 via YouGetsignal.
My ISP has told me that they do not block any ports including port 80.
View 7 Replies
View Related
Dec 7, 2011
I have Verizon FiOs and their provided wireless router does not cover my entire house. There are plenty of dead spots throughout the house (house is 3500sq. ft.)
The FiOS comes into the basement so currently I have their router is set up in the basement. I wanted to shut off their FiOS wireless router and use my new E4200 router for wireless coverage. I am pretty sure the E4200 alone will not be able to handle my house. Most of the rooms of the house are already prewired with Ethernet cables. All those wires converge in the same closet in the basement, therefore moving the router is not an option. I was thinking of putting whichever product you experts recommend in my office which is on the 2nd floor on one side of the house. This room does have Ethernet access. However it is currently at 50-60% signal (with FiOS). My bedroom which is on the opposite side of the house is at 10-20% signal (with FiOS).
I am looking to buy something to reach all the deadspots and have WIRED LAN access (if need be in the future). What is my best option? I have researched the RE1000, the WAP610N, and even some of the other routers (E2500 or E3200) for hours. I am not an expert, and frankly after hours of reading, these technical terms of "range expanding" and "access points" are all sounding synonymous to me. I guess what I need is the range expansion on the same WiFi SSID my E4200 will provide (to cover all areas of my house), as well as an access point for connecting TVs, Xbox, or PCs in the future.
1) RE1000
2) WAP610N
3) or a router to use as an access point/range expansion combo? E2500 or E3200?
Naturally, is the range capability better for Routers or the WAP610N or RE1000?
View 1 Replies
View Related
Sep 5, 2011
I'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies
View Related
Oct 4, 2012
I previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
View 4 Replies
View Related
Mar 6, 2012
what user name do I use to access the E2500 configuration panel. I have used the computer name, adm, adim, and the router default password and I canot log on to the configuration panel.
View 1 Replies
View Related
Feb 28, 2013
I am trying to connect to a new VPN using my E2500 router. As soon as I connect, the connection breaks.
View 1 Replies
View Related
Sep 3, 2012
i buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies
View Related
Dec 18, 2012
I want to add my E2500 as a second wireless router to cover my entire house.I have a Motorola Surfboard SBG6580 cable modem (Time-Warner) at one end of the house.I added via powerline Ethernet connection a new E2500 wireless router at the other end of the house.The E2500 set-up with all defaults and has the same SSID and Password as the Surfboard cable modem.It seems to work OK, but I wonder about network confusion/interference.Do I have to configure the E2500 in some manner to allow seamless roaming of my wireless devices (iPad, Cell Phones, Netbook)?I had an RE1000 with just the Surfboard, but it did not quite do the trick, and does not like both routers connected at either end.
View 9 Replies
View Related
Nov 23, 2011
How To Reset E2500 Router
View 1 Replies
View Related
