Cisco Switching/Routing :: 3500XL - Two Routers On One Switch?
Mar 4, 2012Can I have two different routers (different subnets) on one cisco 3500XL switch and still be able to communicate between the two? If so how can I do it?
View 8 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 3500XL - How To Manage Layer 2 Switch
Sep 5, 2012My understanding is that even layer 2 switches like the Cisco 3500XL can have 1 IP address for management. However, I cannot seem to figure out how to configure it to get it working in a router on a stick setup. I can manage the router through SSH, but I cannot SSH to the switch.
View 3 Replies View RelatedCisco Switching/Routing :: 3500XL Switch - Does Not Load Flash Or Boots
Dec 8, 2011Base ethernet MAC Address: 00:0a:b7:07:35:80Xmodem file system is available. The system has been interrupted prior to initializing theflash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init load_helper boot switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4ô
Cisco Switching/Routing :: Catalyst 3500XL Switch - How To Reset Without Password
Feb 23, 2012have a Switch I bought off a guy at work. Just to get into the Switching world of Cisco. He doesnt know the password on it and i cant reset the switch. I would like to mess around with it more but it doesnt load the flash or helper. It just sits there and holds. I have tried the password recovery and everything. Trust me, everything is correct, but it wont work for me. I cant load a new image to it because I dont have access to a server to get it from.
Base ethernet MAC Address: 00:0a:8a:94:58:c0Xmodem file system is available.
The system has been interrupted prior to initializing theflash filesystem. The following commands will initializethe flash filesystem, and finish loading the operatingsystem software:
flash_init load_helper boot
switch: flash_initInitializing Flash...flashfs[0]: 3 files, 1 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 3612672flashfs[0]: Bytes used: 1815040flashfs[0]: Bytes available: 1797632flashfs[0]: flashfs fsck took 3 seconds....done Initializing Flash.Boot Sector Filesystem (bs:) installed, fsid: 3Parameter Block Filesystem (pb:) installed, fsid: 4û
Cisco Switching/Routing :: 3500xl Switch Will Not Load Flash Or Copy From Xmodem?
Dec 7, 2011I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies View RelatedCisco Switching/Routing :: 3500XL - Configuration Switch Port Mode Access
Mar 5, 2013I am trying to configure a 3500XL switch (and I know its old). I get to the int fa 0/1 line and thats where it all stops working.
switch#(config-if)#switch port mode access
switch#copy run start
or
switch#(config-if)#switch port mode access
switch#sh run int fa 0/1
It will show the configuration for port fa 0/1 as if I hadn't entered the "switch port mode access" command. Or any other command for that matter. Why the switch is not holding configuration and seemingly loses it as soon as you exit out of each interface?
Cisco Switching/Routing :: Catalyst 3500XL Cannot Get Into The Flash Dir
Apr 22, 2012I've gotten this out of our storage unit here at work: This was not in use, I've restarted it, I can't get into the flash dir,I've tried to restart the switch via the documents I've gotten on the site.I have the lastest iOS version .bin for this switch, but I can't get this to load: here below is what happens when I try.
View 5 Replies View RelatedCisco Switching/Routing :: 3500XL To Add Ip Address On Vlan 21
Apr 27, 2012I have a POE switch running 12.0(5). I have port 24 connected as a trunk connected to the main switch. I need to add an ip address on vlan 21 which is where the network vlan is. I created it but I can not seem to enable it. I have issued the no shut command several times, but doing "sh ip int brief" it keeps showing up as administively down.
View 13 Replies View RelatedCisco Switching/Routing :: 3500XL / VLAN Interfaces Will Not Come Up
Jan 9, 2013I am using an Old 3500XL and I simply created a
interface VLAN 100
Description ***********
ip address 10.0.1.100 255.255.255.248
no ip directed-broadcast
no ip route-cache
shutdown
no matter what I do i cannot get it to come up, the rest of the switch is default config, I know I am just forgetting something, But I don't know what?
Cisco Switching/Routing :: 3500XL Computer Doesn't Get IP Address
Jul 10, 2012I'm configuring a catalyst 3500XL, but I'm having a problem, when I connect an ip phone it works just fine but if I connect a computer to the pc port in the phone the computer doesn't get an ip address. The switch is configure with two vlans Voice and Data and is connected from fa0/24 to a Catalyst 3560 fa0/46. I did configure both ports as trunk.
View 9 Replies View RelatedCisco Switching/Routing :: Trunking Between 3500XL And 3Com 4800g
Oct 14, 2012I am trying to trunk between a 3Com 4800g and a Cisco 3500xl. I can get the a PC that connects to a vlan 1 port on thecisco switch to connect to the 3com switch and get connectivity. However, I cannot get anthing on the cisco switch that is on vlan 2 to connect and get dhcp. I am not a 3com guy, so I am not familiar with the command and configs.We have 2 vlans on both switches: Vlan 1 is Admin and Vlan 2 is Student.
View 17 Replies View RelatedCisco Switching/Routing :: 3500XL Can Use Fiber Ports To Connect To PC
Mar 7, 2012I have an old Cisco 3500XL I am using for my home lab, but was wondering can I use the fiber ports to connect to my PC. I have to correct NIC interfaces but no link indication. I did make sure the port was no down, but sill not link.
View 8 Replies View RelatedCisco Switching/Routing :: 3500XL / DCHP Requests Blocked Inside VLAN?
Jul 7, 2012i have several cisco 3500XL switches with trunking. I created a VLAN lets say 20 which purpose is for wireless clients. I installed wireless controller with 4 APs and controllers sees all 4 APs. Controller is also DCHP server. When wireless client authenticates it's DCHP requests in not getting to DHCP server (controller). If i connect all equipment in non managed switch everything works.
View 10 Replies View RelatedCisco Switching/Routing :: 3500XL - Same DHCP Server Serving Requests For 2 VLANs
Jul 18, 2012I have several Cata 3500XL switches connected to one 1 HP L3 switch which is connected Sonicwall router. Vlan1 has subnet of 10.10.0.0/24 and Microsoft DCHP server lays inside VLAN1.
Now i want to add VLAN11 (192.168.10.0/24) as second data VLAN but DHCP requests should go to microsoft DCHP server.
This is what i did:
Configured VLAN11 IP on each cisco switch
IP default gateway with IP from other subnet (i guess this is bad since maybe it should be IP of VLAN11 on HP L3 switch?)
Trunk ports are configured to pass everything on cisco switches
On VLAN11 i configured IPhelper IP to be MS DHCP server on each Cisco switch
I haven't tested this yet but i have problem in process.I can't ping VLAN11 IPs between switches (i configured VLAN1 and VLAN11 with IP). When client plugs computer to a port that belongs to VLAN11 will i be sure that client will get IP from the 192.168 range or there is possiblity that he gets IP from the management VLAN range?
Cisco WAN :: 3500XL Cannot Enable The Switch
Mar 31, 2013I was trying to upgrade IOS on my 3500XL series switch (24 port) Before doing this I connected my switch and deleted all the configs and flash. When I reconnect my switch this is the error message I am getting.
View 7 Replies View RelatedCisco Switching/Routing :: 3560E Switch 10 Gigbit Uplink For The Switch
Apr 23, 2012I need 10gigbit uplink for this switch. What are the other devices that i need order along with this device.And what is the diff between X2-10GB-LR= and CVR-X2-SFP.if i take CVR-X2-SFP, in future how can i upgrade from one gig to 10 gig?for current use i need 10gig support required. so what are all the other devices that i need to order.Fiber multimode and distance 15Mt only.
View 2 Replies View RelatedCisco Switching/Routing :: 3750 / 3800 - Configure Trunk Between Switch And Extreme Switch
Nov 2, 2011i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View RelatedCisco Switching/Routing :: What Is The Use Of No Switch Port Command In L3 Switch
Dec 28, 2008what is the use of no switch port command in L3 switch?
View 7 Replies View RelatedCisco Switching/Routing :: 3750-X Stacking Switch By Switch
Nov 18, 2012I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 4006 / Quickly Copy Configuration From Production Switch To Spare Switch?
Nov 20, 2009I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedCisco Switching/Routing :: Cat 3560 No Switchport Command Test Out Routing With Switch
Dec 8, 2011The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
Cisco Switching/Routing :: Inter-VLan Routing On Catalyst 3750 Switch
Dec 17, 2011I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
Cisco Switching/Routing :: 3825 / Replacing Routing Function With 3750 Switch?
Jul 27, 2012I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
Cisco Switching/Routing :: Inter-VLAN Routing Using 877 And SG300-10 Switch
Feb 5, 2012I recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
Cisco Switching/Routing :: 3560 VLAN Routing Between Switch And Router
May 8, 2012I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
Cisco Switching/Routing :: About Intervlan Routing On Catalyst 3750 Switch
Apr 16, 2012I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedCisco Switching/Routing :: Routing Secondary Network On 3560 Switch
Jun 4, 2013I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
Cisco Switching/Routing :: Cannot Reach Gateway Through Routing Switch (3750)
Mar 11, 2012I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
Cisco Switching/Routing :: 2960 / SG 300 Switch - VoIP Setup - Asymmetric Routing Not Working
May 21, 2013I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
Cisco Switching/Routing :: Static Routing With C2960G Switch
May 28, 2013Two Cisco C2960G Switches connected with each other using an EtherChannel Trunk Ports.IOS Image has been upgraded to c2960-lanbasek9-mz. 122- 58.SE2.bin.The global command "sdm prefer lanbase-routing" has been executed to set the default template to "lanbase-routing".The global command "ip routing" has been executed to enable the ip routing.An IP route has been configured in each switch to point to each other for the static routing purpose (Please see the 2 attached configuration files) The hosts in VLAN 111 and VLAN 110 are not able to see each other even the ip static routes have been configured.May be I have misconfigured some settings but not sure what's the actual problem.
View 11 Replies View RelatedCisco Switching/Routing :: InterVLAN Routing On Switch 3750X?
May 22, 2013my company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
View 10 Replies View RelatedCisco Switching/Routing :: ME3400 Switch Set To Routing SDM Template
Dec 18, 2012You can set the ME3400 switch set to the Routing SDM template such that it support PBR. That is done in the ASICs, right? Because if it is done in software the switch could quickly become overwhelmed.
View 2 Replies View RelatedCisco Switching/Routing :: 3550 / Layer 3 Switch Not Routing?
Apr 26, 2012I have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....