I have couple C2960G and C3750. Is there any way to filter (on ingress port) type of traffic? I would like to allow IP only, and discard (i.e.) IPX, or other garbage, that any device can produce.I have tried to find something about this, but only thing I have found is feature : protocol filter, which doesn't seems to be working on my hardware.
View 6 RepliesCan the SRP547W be configured to allow traffic on port 25 from an external ip range to an internal address?
View 0 Replies View RelatedAs above, I got a problem with C3750e, ios c3750e-universalk9-mz.122-58.SE1.bin, when send AF41 traffic passing through it. My topolygy is as following
WAN link <----------> G0/0/2.100 - ASR1002 - G0/0/5 <---------> G1/0/1 - C3750e - G1/0/3 <--------> G0/0/1 - ASR1004
On this C3750e, I turned on mls qos, trust dscp on both G1/0/1 and G1/0/3 and no else is configured. ASR1002 G0/0/2.100, i applied the CB shaping fror AF41 traffic.
C3750e#sh mls qos
QoS is enabled
QoS ip packet dscp rewrite is enabled
C3750e#sh mls qos int g1/0/3
GigabitEthernet1/0/3
trust state: trust dscp
[code]....
Then, from ASR1004, i send ICMP traffic with TOS set to AF41 (136) and i found out that
1. The traffic is dropped on c3750e
sh mls qos int g1/0/3 statistics
GigabitEthernet1/0/3 (All statistics are in packets)
30 - 34 : 63 63 48 86 1534
2. The traffic never get hit into AF41 class in ASR1002 ? Why C3750e dropped this AF41 traffic? and what can I do to fix it?
I am facing port speed issue on WS-C2960G-48TC-L series switch.This switch gig0/X ports connected to onother switches (Cisco and HP both switches are also gigbit ports and directly connected ).but interface is giving only 100mb/s output.ios on WS-C2960G-48TC-L is 12.2(44)SE6
View 15 Replies View RelatedWe have a lot of IPX traffic flowing through a switched network and we are being asked to filter it from a network standpoint. At one point they were using IPX in their network, but no longer need to, so they still have a lot of machines spewing out IPX traffic. We have removed the IPX routing commands from our distribution switches, (Cisco 6500), but after running a short 10 minute Wireshark capture I'm still getting a good bit of IPX traffic from a lot of different devices.
View 2 Replies View RelatedI have a ASA 5585 and a Nexus 5596, and i need a sugestion to configure this cenário:
My users in the Vlan 10 need access on the network in the Vlan 20, but this traffic must be filtered for firewall. In the firewall a received a trunk port for Nexus 5596, and i created subinterfaces to receive the Vlans for this trunk.
The gateway for my users is the address for the ASA subinterfaces.
What i do to filter the traffic between the Vlans?
I have stacked WS-C3750E-24PD with Ten Gigabit Ethernet ports configured under ether-channel. It has c3750e-universalk9-mz.122-55.SE1.bin IOS installed on it. One of the Ten Gigabit Ethernet ports, goes to err-disable mode with following errors on that specific ports.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm.
%SFF8472-5-THRESHOLD_VIOLATION: Te1/0/2: Tx power low alarm; Operating value: -31.0 dBm, Threshold value: -9.0 dBm. (DROmx-1-1)
I have gone through some of CSC forums like {URL}. The workaround is to "Remove the X2 or SFP from the inactive up link port" which is not in my case.
We want to filter IP traffic by MAC address on Catalyst 4500. Since we are using bonding (active-backup mode) we need those mac addresses appear on different ports. Below are solutions that we have tried: ACL but it does not work since mac acls only match non ip traffic (We CAN NOT use ip acl). Use a static mac address-table entry to ALLOW specific mac addresses. It does not work either since the same MAC address needs to be seen on a different port. Catalyst 4500 does not support auto-learn option (as e.g. Nexus 5000).
View 3 Replies View RelatedIn our company 3nos Cisco 3750 (WS-C3750-48P) access switch in stake mode. All port are assigned with voice and data Vlan also Avaya IP connected with this switches. From last few days tow port 2/0/7 and 2/0/8 is showing amber and status is showing err-disable. At Avaya end it is showing a message “ETHERNET WAITING” in phone dispaly. I try to connect laptop directly with these ports but it is showing "Cross Connectivity". [code]
View 4 Replies View RelatedI'm decommissioning my SonicWall PRO 3060 and upgrading to an ASA5550 (we're increasing our WAN link speed to 1Gig and need the 5550). In any case, I want to copy over the configuration from the PRO to the ASA. I have everything documented and I've started doing the changeover, but in looking at some other network diagrams on the net I'm seeing router symbols between the LAN switches and the ASA and I'm beginning to worry that I might need routers to do this which, of course, would increase cost quite a bit.
So my question is this: If I have a core switch carved into multiple VLANs and I connect each VLAN to a port on the ASA, will I be able to route and filter traffic from VLAN to VLAN through the ASA? If so how, in general, is this accomplished (I'm betting ACLs). I think that the ASA will be able to do this easily, but I just want to be sure before I get too far into the configuration of this unit,.
ASA
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
GigE0/0 GigE0/1 GigE0/2 GigE0/3 GigE1/0 GigE1/1 GigE1/2 GigE1/3
| | | | | | | |
| | | | | | | |
WAN BackupWAN VLAN400 VLAN500 VLAN600 VLAN700
I am having an issue on a Cisco 3750 stack where when the stack master is rebooted, all my lacp port-channels drop and then come back up again. After doing some investigation It seems that it is happening because of lacp using the stack master mac-address as part of the system-id, so when the stack master reboots, the stack mac changes. I see that there is the command: stack-mac persistent timer 0
There is this warning about using this command:
When you configure this feature, a warning message displays the consequences of your configuration. You should use this feature cautiously. Using the old master MAC address elsewhere in the domain could result in lost traffic.
My question are:
Are there any other consequences to using this command (apart from moving the switch/mac to another location in the network)It mentions 'If the entire switch stack reloads, it acquires the MAC address of the master as the stack MAC address' Is this still the case if you have the stack-mac persistent timer to 0? Does using channel-group mode on for the port-channels still use the same mechanism of having a system-id? (Will the channels flap using 'mode on' when rebooting the stack master.
Why I cannot ping vlan when no port connect to switch.
View 3 Replies View RelatedIs there any way to Mirror a CISCO C3750 Switch Port Taffic to a remote Host IP Address?I know Port Mirror (SPAN/RSPAN) can copy one Interface Packet to another Interface. But I am looking for a way to miror Switch Port Packets to a remote Host (having Public IP Address and running Wirehark). Is it possible?
View 9 Replies View RelatedI'm currently configuring per port policing on a 3560 and want to limit inbound traffic to 750mbit:
mls qos
access-list 1 permit any
class SET_IF
match access-group 1
policy-map SET_QOS
class SET_IF
[code].....
When I test the setup with iperf I always get different results when I change the nummber of parallel connections.Isn't there a way to limit the throughput regardless of the number of conns (INGRESS!) like with srr-queue bandwith limit?
I am having an issue with connecting to a Cisco 7201 via the AUX port through a modem. The modem is plugged into the AUX port and I am dialing into the modem, everything seems to be working fine as I get a login prompt and my banner etc but I can't type anytihng. If I type then nothings happens... If I just type a bunch of random characters on the keyboard then when the authentication prompt times out and it goes back to the username, it will show a few of those characters.. I have tried many things, changing speeds etc, I have even tried changing modems and it is doing the exact same thing.Here is my config:
line aux 0 exec-timeout 2 0 modem Dialin transport input all stopbits 1 speed 115200 flowcontrol hardware
I have searched on here and found people having similar problems but no solutions. I have tried this one a Cisco 2821 with the same config and it works with no problem, the only difference is the phone line is different.
If i fully populate all switch port (Cisco 3750 series) with 100 filter list on each port is it recommendable.
View 4 Replies View RelatedI am trying to filter ARP answer arriving on a C6500 trunk port, for a specific vlan.Filtering conditions are:
- packet arrive from vlan ID x on the trunk (on only for this vlan ID)
- source MAC address = xx:xx:xx:xx:xx:xx
Thae aim is that the C6500 with never enter into its CAM table this MAC address.I looked at several methos like service policy or vlan filter, but no solution for the moment.
How does a firewall block or filter traffic on a specific port or IP address?
View 1 Replies View RelatedWe are planning to implement the following policy map for egress traffic on an Nexus 7000:
policy-map type queuing dd-1p3q1t-8e-out-10G class type queuing 1p3q1t-8e-out-pq1 priority level 1 shape percent 10 class type queuing 1p3q1t-8e-out-q2 bandwidth remaining percent 5 class type queuing 1p3q1t-8e-out-q3 bandwidth remaining percent 5 class type queuing 1p3q1t-8e-out-q-default bandwidth remaining percent 90
We are using two N7K's to which is one N5K connected through a vPC. From the N5k we use a port-channel with 4 * 10G. Two of this four ports are connected to on N7K and the other two are connected to the other N7K. On the n/K's we are using vPC.
My question now are:
1. Where i have to connect the policy map? To the port-channel or on each physical interface?
2. When i have to connect this policy to the port-channel, how does i have to set the shape percent, when i would like to reserve 10% from the 40G? Does i have to set the shape value to 5% on each N7K because vPC?
Two Cisco C2960G Switches connected with each other using an EtherChannel Trunk Ports.IOS Image has been upgraded to c2960-lanbasek9-mz. 122- 58.SE2.bin.The global command "sdm prefer lanbase-routing" has been executed to set the default template to "lanbase-routing".The global command "ip routing" has been executed to enable the ip routing.An IP route has been configured in each switch to point to each other for the static routing purpose (Please see the 2 attached configuration files) The hosts in VLAN 111 and VLAN 110 are not able to see each other even the ip static routes have been configured.May be I have misconfigured some settings but not sure what's the actual problem.
View 11 Replies View RelatedI'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
Default Gateway of ISP----> Switch------->Router
From my router, I can ping Gateway, however I cant ping the switch (WS-C2960G-8TC-L) in between.
I managed to upgrade this C2960G-48TC-L from 12.2.35-SE5 to 15.0.2-SE1 and now I can't connect anymore via telnet nor ssh. Console output simply shows
%% Low on memory; try again later
How do I do a factory reset on a Cisco Catalyst WS-C2960G-8TC-L switch?
View 2 Replies View Related[URL]
I'm at task 6
Am I wrong but the only way to filter external routes - type 5 - is with a stub area, and area 0 can't be a stub? As far as I know OSPF can't filter on the route tag, so should I be filtering with a route-map?
Been dealing with a strange problem for several days now. It started out with a problem that I thought was VTP related but ended up being something else. I setup a span port on a 3750 that I am connected to that was mirroring the trunk connection coming into the switch.
Never saw an VTP traffic come across the connection but doing a sh vtp status indicated the traffic was arriving and getting processed. When I found some debug commands (debug sw-lan vtp), I was also able to see the packets go between switches. Seeing this issue concerns me that there is other traffic that isnt showing up during a span session.
I know that doing a span on a switch, especially using a trunk port as a source, isnt a good idea. Since I didnt have a TAP at time, this was my only choice. I have since borrowed a NetOptics TP-CU3 tap from a good friend and was able to confirm the VTP traffic was going across the trunk connection between switches.
All of my 3750's are running 12.2.55.SE.
How do I redirect my port 80 traffic to my Trend Micro IWSVA in my 3550 switch? How do I use PBR? Can I use WCCP in my 3550?
View 3 Replies View RelatedNetworking is not my gig, but it has to be at this very moment. We have an ASA 5505. Let me explain what's going on.
On Tuesday I wanted to be able to use the ASDM since there is less room for error. But we only had a console set up. So I ran the following commands...
in ($config)
http of course didn't do anything incomplete command
http 192.168.1.2 255.255.255.255 didn't anything incomplete command
http 192.168.200.254 255.255.255.255 inside
[Code]....
Everything started working after that. Everything worked fine all of wednesday and thursday. Then this morning it stopped processing again. When I traceroute it gets to the machine that is hooked up to the console and stops. So I'm guessing its actually getting to the ASA router and being swallowed up again...
I am looking to find a command or counter to tell me if a cisco switch port on a 4510 was ever up and passed traffic. I want to shutdown all unused switchports on our access switches. But before I do that I need to make sure device is just not off or the person is away on vacation. If I do sh int interface, is there a counter I can reference.
View 4 Replies View RelatedWe would like to setup a link to our DR site that is separate from our main network traffic. This link will be used by an EMC VNX SAN for replication traffic. The SAN will be plugged into a fiber port on a 3750 switch and going out from the same switch (going in as multimode, going out as single mode) into a patch panel that runs over to the DR site (about a mile away). At the DR site it will go from the fiber panel into another 3750 switch which ends up going back out of that switch into our DR SAN.
I'm wondering what the best way would be to configure the fiber ports to accomplish this. I'm affraid that the replication traffic will find it's way over through another route and congest our main network unless configured appropriately.
I want to know what is the best way to black traffic inside the same VLAN, this VLAN is a user VLAN, it means that I am talking about access layer.I wanted to use private vlan, but C2960S doesn't support this feature. Any other way to prevent any to any traffic in the user vlan, this vlan only have to speak at the Layer 3.
View 2 Replies View RelatedHow do I limit broadcast/mulitcast traffic on a switchport to e.g. 5000 pps ? I don't want the port to shut down, just block or drop broadcast traffic that exceeds 5000 pps.
View 19 Replies View RelatedSo I took a laptop with wireshark and plugged it into a nexus 5000 port that is configured as a trunk with 3 vlans allowed on it. The laptop was seeing all kinds of traffic on the wire, most of it was not involving my laptop.
For example: Server A VLAN 10= 10.10.10.1 Server B VLAN 20= 10.20.20.1 and wireshark laptop is plugged into a trunk port which is allowing those vlan's. The vlan's are routable.
10.10.10.3 is seeing the entire conversation when 10.10.10.1 backs up 10.20.20.1 even though it has no reason to see it. It is as if the trunk is spanning traffic to the laptop port. No span is setup however. It's really weird. This is not just broadcast traffic, but actual tcp taffic between Server A and B. Why would a trunk port see traffic between 2 other servers talking to each other on the vlan.
Trunk port configuration below:
Interface Ethernet 141/1/3
switchport mode trunk
switchport trunk allowed vlan 10, 20